KI S4SWB Manuale utente
MADE IN USA
INSTRUCTION
MANUAL
S4SWB BELT SANDER
1
WARRANTY
All products are guaranteed for a period of one year to the original purchaser, against defects in material work workmanship,
under normal use
Electric motors are warranted by the manufacturer and will be repaired by the nearest repair station or replaced. Defective
motors are not be returned to Kalamazoo Industries. Please call for instructions (269) 382-2050. Written authorization must be
obtained before returning merchandise.
RETURN POLICY
• Authorization must be obtained before returning merchandise. Please call our Customer Service Department to receive a
return authorization number (269) 382-2050.
• Please include with your return a copy of your invoice or packing slip.
• All returns will be subject to a 10% restocking fee.
• Customer is responsible for paying for return freight.
• No returns will be accepted after one year of invoice date.
BELT SANDER SAFETY
• READ THE OPERATING INSTRUCTIONS BEFORE RUNNING MACHINE.
• ALWAYS WEAR SAFETY GLASSES OR A FULL FACE SHIELD FOR PROTECTION.
• KEEP HANDS CLEAR OF THE SANDING AREA.
• NEVER WEAR GLOVES OR LOOSE FITTING CLOTHES WHEN OPERATING THIS MACHINE.
• ALWAYS KEEP HAIR TIED BACK AND COVERED.
• LET MACHINE ROTATION COME TO A FULL STOP BEFORE CHANGING BELT.
• KEEP SAFETY GUARDS IN PLACE. DO NOT ALTER GUARDS OR MACHINE IN ANY WAY. ANY
ALTERATIONS TO GUARDS AND MACHINE COULD CAUSE SERIOUS INJURY AND WILL VOID MACHINE
WARRANTY.
• ALL BELT SANDERS SHOULD BE OPERATED IN A WELL-VENTILATED AREA. THE DUST CREATED
WHEN SOME MATERIALS ARE SANDED CAN BE HARMFUL. DUST MASKS/RESPIRATORS ARE
RECOMMENDED AS A PRACTICAL MEANS OF MINIMIZING DUST INHALATION. FUMES FROM OTHER
SOURCES CAN ALSO CAUSE FIRES WHEN IN CONTACT WITH SANDING SPARKS.
• NEVER MIX MATERIALS.
• SPARKS CREATED BY SANDING SHOULD BE DIRECTED DOWNWARD AND AWAY FROM THE FACE
AND BODY. DO NOT GRIND NEAR FLAMMABLE MATERIALS.
• ELECTRICAL SANDING MACHINES ARE NOT INTENDED FOR USE IN OR NEAR WATER. THIS
INCLUDES AN OPERATOR STANDING ON A WET FLOOR OR WORKING AROUND CONTAINERS OF
WATER OR OTHER CONDUCTIVE LIQUIDS.
KALAMAZOO INDUSTRIES, INC.
6856 E K AVENUE
KALAMAZOO, MI 49048
PHONE: (269) 382-2050
FAX: (269) 382-0790
WWW.KALAMAZOOIND.COM KI
MADE IN USA
2
BASIC OPERATION
Inspection: If these goods are damaged in transit, the DELIVERING TRANSPORTATION
COMPANY is required by law to make notation of damages on the freight bill. If in your opinion,
there may be concealed damage, they are required to make an inspection after goods are unpacked.
Transportation rates are made in proportion to damage. Therefore, there carrier and NOT the
shipper should be charged with any lose of damage. Any claim should be led with the delivering
Transportation Company. PLEASE DON NOT RETURN GOODS TO US WITHOUT OUR
RGA NUMBER AND SHIPPING INSTRUCTIONS. See front page for Return Policy and
Warranty.
Model: S4SWB is a 4” x 36” wet bench top belt sander, belt speed 3600 SFPM, integral cabinet and
coolant tank, submersible pump, 1/2HP 1PH 115V.
Coolant: Use a rust inhibiting coolant. Consult your dealer for coolant specications.
Work area: The usable belt work are is 4” wide x 6” long. Sanding belt grits vary from course to very
ne. The higher the grit number the ner the sand paper. Consult your dealer for abrasive sanding
belts. Belt size: 4” x 36” wet belt.
Belt tracking: See tracking pictures. Use tracking bolt (B, #11 on parts sheet) to twist upper yoke
(#7) to track sanding belt left or right. Both the aluminum drive pulley (located on the motor) is
crowned along with upper idler pulley (located on the yoke #7). This keeps the belt centered or
“tracked”. The opposing spring (#10) and bolt (#11) on the opposite side of the yoke (#7) keeps the
yoke position.
Belt changing: See tracking sheet pictures. With power OFF, squeeze the sanding belt with your
hand to compress the belt tension spring (#10). With the other hand line up the cam (A, #15) on the
tension shaft to maintain compression of the spring (#10). Remove the sanding belt and replace with
a new belt. Repeat the squeezing of the belt and reposition the cam 90 degree to the tension shaft
(#6) to allow re-tensioning of the belt. Jog the on/off switch to see that the belt is tracking (centered
on the pulleys). You are now ready to run.
Maintenance: Keep the units integral coolant tank cleaned out. To clean out the tank, direct the
coolant line away from the machine into a bucket/bowl, etc.. Wipe out the swarf in the bottom of the
tank. Vary your sanding area on the sanding frame to spread out the “wear” on the sanding frame.
Dishing of the cast frame from wear will cause belt breaking.
Tracking problem: If the sanding belt is not tracking or “centered” more than likely the “crown” on
the drive pulley is worn down at and the belt cannot seek the “high” spot. Replace the drive. The
only bearings that may fail over time would be the idler pulley bearings on the idler pulley. Replace
the idler pulley
Safety: See safety sheet.
Replacement parts: Are available online or over the phone for purchase.
3
4
KALAMAZOO INDUSTRIES
S4SWB 4” X 36” BELT SANDER
PARTS LIST
Indice
