Kia OPTIMA PHEV Manuale utente

Emergency Response

Guide

Version_1

OPTIMA PHEV

(JF PHEV)

1. Identification / Recognition

2. Immobilization / Stabilization / Lifting

3. Disable Direct Hazards / Safety Regulations

4. Access to the

Occupants

5. Stored

Energy / Liquid / Gases / Solids

6. In

Case of Fire

7. In

Case of Submersion

8. Towing / Transportation /

Storage

9. Important

Additional Information

Contents

OPTIMA PHEV

1. Identification /

Recognition

Initial Response: Identify, Immobilize and Disable

Identify

•

The OPTIMA PHEV is an hybrid electric vehicle. Emergency responders should

respond

to emergency scenarios involving the OPTIMA PHEV accordingly, exercising

extreme

care and caution to avoid contact with the high voltage system within the vehicle.

The

following procedures should be used whenever you are dealing with a OPTIMA

PHEV

an emergency scene. However, all operations should be consistent with

your

department's

standard operating procedures, guidelines, and any applicable laws. When

PHEV

is damaged in a crash, the high voltage safety systems may have

been

compromised

and present a potential high voltage electrical shock hazard. Exercise

caution

and

wear appropriate personal protective equipment (PPE) safety gear, including

high

voltage

safety gloves and boots. Remove all metallic jewelry, including watches and rings.

OPTIMA PHEV

WARNING

1. Identification /

Recognition

1.1 Identifying a Kia OPTIMA PHEV

Charging Port

•

The charging port is located on the side of the vehicle.

#Note

: The doors must be un-locked to open the charge port door.

How to open the charging port

Press the unlock door button, depress

the brake pedal and apply the Electric

Parking Brake (EPB).

Turn OFF all switches, put the vehicle in

P(Park)

position and turn off the vehicle.

Open the charging inlet door by pressing rear

center

edge of the charging inlet door

Unlock

charging door in emergency

Orange

Color Cable

Orange color cables run under the floor of the vehicle and under the hood. When opening

the hood, the orange color cable identifies a PHEV.

OPTIMA PHEV

•

If the charging door does not open due to

battery

discharge, open the hood and slightly pull

the

emergency cable as shown left.

•

The charging port door will then open.

1. Identification /

Recognition

1.1 Identifying a Kia OPTIMA PHEV

VIN Label

The

VIN (Vehicle Identification Number) identifies the Plug-in hybrid with a “D”

displayed

the 8th position, as shown in the below drawing.

The VIN can be found:

1) VIN Plate can be seen through the windshield from outside.

2) Underneath the front passenger seat (or driver seat)

On the vehicle certification label attached to the driver’s side center pillar

OPTIMA PHEV

XXXXXXXDXXXXXXXXX

1. Identification /

Recognition

1.1 Identifying a Kia OPTIMA PHEV

The

OPTIMA plug-in hybrid Cluster Instrument Panel displays the PHEV specific

features

such

as high voltage battery SOC (State of Charge) in the highlighted part.

OPTIMA PHEV Cluster Instrument Panel

OPTIMA PHEV

1. Identification /

Recognition

1.1 Identifying a Kia OPTIMA PHEV

Charge Status Indicator

The

High Voltage battery Charge Status Indicator is visible from outside the vehicle. It

seen

through the windshield at the center of the crash pad and is illuminated when

the

vehicle

is plugged-in and charging.

OPTIMA PHEV

2. Immobilization / Stabilization / Lifting

Chock the wheels

Set the Electronic Parking

Brake (EPB)

Put the vehicle

in P (Park) position

2.2 Vehicle Stabilization

Use standard stabilization (lift) points, as

shown beside. Always be sure to connect to a

structural component of the vehicle and avoid

placing cribbing under high voltage cables,

and other areas not normally considered

acceptable.

2.1 Immobilization

The next step is to immobilize the vehicle to prevent any accidental movement that can

endanger response personnel or civilians. When the OPTIMA PHEV is damaged in a crash, the

vehicle may appear to be shut off, even when it actually is not, due to a lack of engine sounds.

When the "READY" mode light is illuminated on the Instrument Panel, the vehicle can move

silently using the electric motor. Responders should approach the vehicle from the sides and

stay away from the front or rear as they are potential paths for vehicle movement. Be sure to

immobilize the vehicle in the following manner.

OPTIMA PHEV

•

When installing a block or jack, avoid high voltage cable, battery and fuel system.

•

If high voltage components or cables are exposed, do not place any support on them.

WARNING

Disable Direct Hazards / Safety Regulations

The

final step in the initial response process, conducted after immobilizing the vehicle, is

disable

the vehicle, its SRS components and the high voltage electrical system. To

prevent

current

flow through the system, use one of the following procedures to disable the vehicle

3.1 Disabling the System – Smart Key System and “POWER”

START/STOP Button

Confirm the status of the READY light

the instrument panel. If the

READY

light is illuminated, the vehicle is ON.

“POWER” START/STOP Button

If the READY light is

NOT

illuminated,

the vehicle is off. Do

not

push

the “POWER”

START/STOP

button

because the vehicle may

start

(go

into READY mode).

To turn OFF the system, put the vehicle in ‘P' (Park) position, and press the

POWER

button

Case I

Power

Off

12V battery

disconnection

High voltage

shut off

Case II*

12V battery

disconnection

Fuse removal

(Fuse box)

High voltage

shut off

OPTIMA PHEV

*In case of emergency

Disable Direct Hazards / Safety Regulations

If necessary, lower the windows, unlock the doors and open the trunk as

required,

before

disconnecting the 12V battery. Once the 12V battery is disconnected,

power

controls

will not operate. (Refer to below “4. –b” for 12V battery disconnection)

Before disconnecting the 12V battery, remove the Smart Key at least 2 meters

away

from

the vehicle to prevent accidental restart.

While depressing the brake pedal

Pressing POWER

button

POWER button

LED color Vehicle condition

One time Off Ready to drive

Without depressing

the brake pedal

Pressing

POWER button

LED color Vehicle condition

One time Amber Electrical accessories are operational.

Two times Reddish orange The warning lights can be checked

before the vehicle is started.

Three times Off Off

OPTIMA PHEV

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Kia Automobile

Manuali Automobile popolari di altre marche

Toyota

Toyota 2000 Tundra Manuale utente

CITROËN

CITROËN DS4 DSign Manuale utente

Lexus

Lexus 2015 CT 200h Manuale utente

Cadillac

Cadillac CTS 2008 Manuale utente

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Manuale utente

Porsche

Porsche Boxster S Manuale utente

GMC

GMC 2010 Savana 1500 Cargo Manuale utente

KIAM

KIAM SPORTAGE 2014 Manuale elenco delle parti

GMC

GMC 2013 Terrain Istruzioni per il montaggio

GMC

GMC T-Series 1999 Manuale utente

Mercury

Mercury 1998 Mystique Manuale utente

Mercury

Mercury 2007 Mariner Manuale utente

Mazda

Mazda 2007 Mazdaspeed 3 Guida

Mazda

Mazda 2014 CX-5 Manuale utente

GMC

GMC Chevrolet Express 2022 Manuale utente

GMC

GMC 1997 Jimmy Manuale utente

Chevrolet

Chevrolet 2012 Malibu Manuale utente

Cadillac

Cadillac 2010 Escalade Manuale utente