KICK ASS KASMARTBG Manuale utente
®
SMART
BATTERY
GUARD
KASMARTBG V0.8
USER MANUAL
1
ŸTo avoid injury or damage to your vehicle ensure instructions are read carefully.
ŸIf you are unsure about the device installation, consult the supplier or an auto-electrician.
WARNINGS
This manual will give you all of the essential information you need to own and operate your
new KickAss Smart Battery Guard.
Features and benefits of KickAss Smart Battery Guard are:
Bluetooth connectivity - Fully programmable via IOS and Android Bluetooth Application, view live
battery voltage and control the relay status ON/OFF from the Bluetooth Application.
Programmable Voltage Sense Relay (VSR) - Fully configurable VSR to isolate the starter battery
from the auxiliary battery when no charge is detected from the isolator.
Programmable Low Voltage Disconnect (LVD) - Fully configurable LVD to protect your vehicles
battery system from over-discharge when connected to auxiliary loads.
Remote Override Switch - Remote override switch with quick connect / disconnect connector to
control the KickAss Battery Guard relay status. Fitted with a 2.8m cable for remote operation.
Heaps of Hardware - All the installation hardware required provided in the box
KickAss Battery Guard Functional Description
Automatic VSR Function overview: Voltage Sensing Relay
The VSR provides automatic protection of the starter battery from over discharge for a basic dual-
battery system without a DCDC charger. The KickAss Smart Battery Guard (KASMARTBG) comes
pre-configured with automatic cut-in and cut-out voltages to protect the vehicle starter battery from
accidental over discharge. When configured as a VSR, the KASMARTBG will isolate the starter
battery from the auxiliary battery to disable any charge transfer between the batteries after the
engine has been switched off.
Automatic LVD Function overview: Low Voltage Disconnect
The LVD provides automatic protection for an auxiliary battery from over discharge when
connected to system loads. The KASMARTBG pre-configured with recommended automatic cut-
out and cut-in voltages to protect the auxillary battery from over discharge.
Note: The KA SBG can only be configured as an LVD device through the Bluetooth Application.
Manual Function overview:
The manual override function, controlled either through the LED Button on the KASMARTBG or the
Bluetooth Application can be used to override the configured automatic cut-in and cut-out settings
to either reconnect or disconnect the system batteries, regardless of the starter battery voltage.
Note: Jump starting from the auxiliary battery should only performed with suitable battery types.
Remote Override Switch overview:
With its own set of functions, the switch can also be used to override the automatic configurations.
Easy to install using the peel off sticky backing and quick connect plug, remotely engage the
KASMATBG to facilitate jump starting from the vehicle cab when needed.
For more further technical details and specifications, please visit kickassproducts.com.au
2
SPECIFICATIONS
INPUT VOLTAGE:
MIN STANDBY CURRENT:
MAX CONTINOUS CURRENT:
CRANKING CURRENT:
OPERATING TEMP RANGE:
CONNECTION:
BLUETOOTH:
UNIT WEIGHT:
UNIT DIMENSIONS:
PACKAGE WEIGHT:
PACKAGED DIMENSIONS:
8 -18V (12V BATTERY SYSTEM ONLY)
1MA
100A
250 - 300A FOR LESS THAN 10 SEC
-20°C TO120°C
M8 PLUS POSITIVE
TERMINAL POST CLAMP
BLE4.2
0.34KG
81 X 76 X 21MM
0.4 KG
200 X 140 X 40MM
SMART BATTERY GUARD CONFIGURATIONS
LVD
CONFIGURATION
VSR
CONFIGURATION
3
PRODUCT OVERVIEW
BAT+ Positive Post
M8 x16 SS Bolt & Washer
KASMARTBG Module
Button/Indicator LED
Remote Override Switch 2.8M
Note: KASMARTGB will be delivered with all hardware depicted above.
BAT+ Positive Clamp
LOAD+ Terminal
M8 Thread Insert
Switch plug
Negative
Terminal
Wire
4
INSTALLATION GUIDE
KASMARTBG VSR Connection with Aux Battery
KickAss Smart Battery Guard VSR Installation Under Bonnet with Auxiliary Battery.
VSR Function overview: Protection for starter battery over discharge with basic dual battery
system. KASMARTBG will be delivered by default as a VSR.
Default VSR Settings: Cut-in voltage - 13.2V | Cut-out voltage: 12.25V
Recommend VSR Settings (AGM/GEL/WET/CAL): Cut-in voltage - 13.2V | Cut-out voltage: 12.6V
Typical Starter Battery Connections
Chassis
Ground
Vehicle
Positive
Battery Positive Post
Remote Override Switch
Load Positive
AUX Battery
Chassis Ground
Starter
Battery
AUX Positive
Chassis Ground
Vehicle Positive
Starter Battery
Vehicle Positive Clamp
Battery Positive Post
Negative Terminal Wire
KASMARTBG
5
KASMARTBG installed to Start Battery
1. Remove vehicle positive
clamp from battery post.
2. Fit vehicle positive clamp to
KASMARTBG positive post.
3. Fit KASMARTBG clamp to
battery post.
4. Tighten both clamps
carefully.
5. Connect remote override
switch if needed and run to
cab dash.
6. Remove M8 bolt from
LOAD+ terminal and fit all
load positive cables.
7. Secure KASMARTBG
Negative Terminal wire to
battery negative.
6
KickAss Smart Battery Guide LVD Installation Under Bonnet with Auxiliary Battery
LVD Function Overview: Protection for Aux battery over discharge with system loads. To
configure the KASMARTBG as a LVD, connect via the Bluetooth Application and configure Cut-in
and Cut-out Voltage.
Recommend Settings (AGM/GEL/WET/CAL): Cut-out voltage: 10.5V | Cut-in voltage - 11.5V
Typical Aux battery connections with NO LVD
KASMARTBG Installed with Aux battery loads
Aux Battery
Charger
Positives
Load
Positives
Load
Negatives
Aux Battery
Charger
Positives
Load Positives
Load
Negatives
KASMARTBG Module
Remote
Override
Swith
Negative Terminal Wire
7
KASMARTBG install to Aux Battery
1.Remove M8 bolt from auxillary battery positive terminal, fit KASMARTBG BAT+ to
auxillary battery positive terminal, add charging positive connections here also, then
screw down bolt.
2.Remove M8 bolt from KASMARTBG LOAD+ terminal, fit auxillary load connections and
screw down bolt.
3.Secure KASMARTBG Negative Terminal wire to battery negative.
8
CONNECTING VIA THE BLUETOOTH APPLICATION
Use the QR codes to download the KA Smart Battery Guard Bluetooth application
Connecting to the KASMARTBG:
ŸEnsure Bluetooth is enabled on the
mobile device.
ŸThe Bluetooth application will begin to
search for any available KASMARTBG
devices when the application is started.
ŸOnce the Bluetooth application can see
the KASMARTBG, the device and
received signal strength will be
displayed.
ŸClick on the device icon to connect.
IOS Android
Registering the KASMARTBG on the
mobile device:
ŸTo register the KASMARTBG with the
mobile device, select OK when
prompted.
9
Verifying the mobile device with
the KASMARTBG:
ŸTo verify the mobile device with the
KASMARTBG, press the LED Button on
the KASMARTBG.
KASMARTBG parameters
and date:
ŸCurrent Starter Battery- Voltage is
displayed at he top of the application.
ŸMode - Indicates the current operation
mode, either automatic or manual.
ŸRelay - Indicates the current state of the
relay.
ŸCut out voltage - Configurable
parameter at which the KASMARTBG
will disengage the relay once the starter
battery voltage drops the below set
voltage.
ŸCut out timeout - Configurable
parameter of time which the
KASMARTBG will wait before
disengaging the relay once the starter
battery voltage drops below the cut-out
voltage
ŸCut in voltage - Configurable parameter
at which the KASMARTBG will engage
the relay once the starter battery Voltage
rises above the set voltage.
ŸCut in timeout - Configurable parameter
of time which the KASMARTBG will wait
once the starter battery voltage rises
above the cut-in voltage
Indice
Altri manuali KICK ASS Accessori per fotocamere
