Kicker 19417164 Manuale utente



19417164

Designed for 2019 and newer

Chevrolet® Silverado/GMC®

Sierra 1500 as well as 2020

and newer 2500/3500 Crew

Cab or Double Cab trucks.

SubwooferHarness

Fuse

AdaptorHarness



SubwooferPowerHarness

WireTies

SubwooferAssembly

19417164-20231006



1. Disconnect negative battery cable.

2. Remove the cover of the battery junction box. Fig. 1

3. Make sure supplied fuse is not installed in fuse holder and connect the subwoofer power wire to

the stud pictured in figure 2. Torque to 4.7Nm (42in-lb)

Route the subwoofer power wire toward the passenger side firewall and secure with supplied wire

ties.

2019-2023 Trucks

4. Find the rubber grommet behind the battery and cut the end of the accessory tube. Feed the

power wires through the grommet tube into the cabin. Fig. 3 Continue to step 9.

Connect one power

harness to each

terminal

Fig. 2 Fig. 1

Fig. 3



2024 and newer Trucks

NOTE: The newer style grommet requires using a fish tape or some type of stiff wire to

penetrate the grommet. There is a provision in the grommet to allow the power

harness to pass through the grommet.

DO NOT TRY TO PENETRATE THE GROMMET ANY OTHER WAY THAN DESCRIBED.

5. Using electrical tape, tape the power harness to the fish tape or stiff wire as shown with one of

the three terminals pointed back along the power harness. Fig. 4

6. Start taping about two inches in front of the power harness and continue about two inches past

the terminal pointing backwards. Applying a thin coat of oil along the electrical tape will aid in

passing through the grommet. Fig. 5



7. Find the rectangular plastic

opening at the 6 o’clock position

of the grommet and insert the fish

tape or wire through it. There will

be some resistance until the

rubber is pierced. Pass the fish

tape into the cabin carefully to

avoid hitting any wires on the

inside of the cabin. You should

now be able to reach up to the

backside of the grommet

underneath the dash and pull the

fish tape and power harness into

the cabin. Fig. 6

Fig. 4 Fig. 5

Fish Tape or

Stiff Wire

Fig. 6



8. Install the white three pin power connector on the subwoofer power wire. Close the retainer.

Fig. 7

9. Connect the subwoofer power wire to the subwoofer harness. Fig. 8



10. If equipped with power seats, adjust the passenger seat as high as possible. Remove the panel

next to the seat. Fig. 9

11. Remove the front kick/sill trim panel as well as the rear sill panel. Fig. 10

12. Connect the ground wire to the ground point

located in the right front kick panel area. Fig.

11 Tighten to 7.5Nm (66in-lb)

Fig. 11

Fig. 8

Fig. 9 Fig. 10

Then close

retainer

Insert terminals first. Any

wire can be in any position.

Fig. 7



13. Remove the four screws securing the front

and rear wire protector and route the

subwoofer harness alongside the factory

harness securing with supplied wire ties.

Replace wire protectors. Fig. 14



Fig. 12

Trucks without Bose® audio system

1. Locate the audio control module next to the

glove compartment and disconnect the two 28

pin connectors. Fig. 12

2. Find the connector with the solid blue and

brown/blue stripe wires and peal back the

cloth sheathing.

3. Connect the green wire of the adapter harness

to the blue wire and the brown wire of the

adapter harness to the brown/blue stripe wire -

See Splicing Technique Section.

4. Connect the adapter harness to the subwoofer

harness.



Fig. 13

Trucks with Bose® audio system

1. Find the harness that runs from the kick panel

area toward the rear of the truck.

2. Using a seam ripper, carefully cut a slit in the

sheathing.

3. Find the twist pair of wires that are yellow and

yellow/black. Connect the green wire of the

adapter harness to the yellow wire and the

brown wire of the adapter harness to the

yellow/black wire. Fig. 13 - See Splicing

Technique Section

4. Connect the adapter harness to the subwoofer

harness.

Fig. 14



14. Remove the two 10mm nuts securing the

jack bracket. Fig. 15

15. Remove the jack tool bag.



NOTE: If equipped with the optional

carpeted storage tray as pictured in

Fig. 12, remove at this time. The

storage tray cannot be used in

conjunction with the subwoofer. The

subwoofer by design provides an

optional storage area once it is

installed.

16. Remove the outer rear seat bolt on the

driver’s side. Fig. 16

17. Make cuts in the carpet according to the

measurement in Fig. 17. Only make cuts

where dotted lines are shown.



Fig. 15

1inch

Fig. 17

Fig. 16



18. Route subwoofer harness from passenger’s

side to driver’s side under carpet.

Subwoofer harness should be routed

behind seat brackets. Routing from one

precut opening to the next will aid in

harness routing. Fig. 18



19. Route the black four pin subwoofer connector out of the hole that was cut near the stud where

the jack tools attach. Route the white amplifier connector behind seat bolts and out of the hole

that was cut near outer seat bolt. Fig. 19



NOTE: Some subwoofers may be

shipped with an additional 12-inch

adaptor harness connected to the

subwoofer amplifier. If so, tuck the

additional harness underneath the

carpet as well while positioning the

subwoofer into location.



20. Make wire harness connections to

subwoofer and amplifier and set subwoofer

in place aligning brackets with the stud and

seat bolt hole. Fig. 17

NOTE: If equipped with the optional

rear rubber floor liner, use the

subwoofer enclosure as a template to

mark the liner around the outside edge

of the subwoofer enclosure. Using a

razor knife or shears, remove the

portion of the rubber floor liner directly

below the subwoofer enclosure.

21. Reinstall the jack tool bag and nut.



NOTE: MAKE SURE WIRE HARNESS IS NOT BEING CRUSHED UNDER JACK

TOOL BAG!

Fig. 19

Fig. 17

Fig. 18



22. Reinstall seat bolt. Torque to 109Nm (80ft/lb)

23. Reinstall all previously removed parts in reverse order.

24. Install supplied fuses into fuse holders.

25. Reconnect negative battery cable. Tighten to 7.5Nm (66in-lb)



SplicingTechnique



Splicing Copper Wire Using Splice Sleeves. Special Tools:

•

EL-38125-10 Splice Sleeve Crimping Tool

•

J-38125-5A Ultra Torch Special Tool

•

J-38125-8 Splice Sleeve Crimping Tool

Note: The DuraSeal splice sleeves have the following 2critical features:

•

A special heat shrink sleeve environmentally seals the splice. The heat shrink sleeve contains a

sealing adhesive inside.

•

A cross hatched (knurled) core crimp provides the necessary low resistance contact integrity for

these sensitive, low energy circuits.



Use DuraSeal splice sleeves where there are special requirements such as moisture sealing. Follow the

instructions below in order to splice copper wire using DuraSeal splice sleeves.

Splice Sleeve Color Crimp Tool Nest Color

W i re G a u g e m m ² / ( A W G )

3 Crimp Nests 4 Crimp Nests 



Salmon (Yellow-Pink) 

19168446

Red (1) or Red/Green (1)

Red (2)

0.5–0.8/(18–20)

Blue 

19168447

Blue (2)

Blue (3)

1.0–2.0/(14–16)

Yellow 

19168448

Yellow (3)

Yellow (4)

3.0–5.0/(10–12)



Note: You must perform the following procedures in the listed order. Repeat the procedure if any wire strands

are damaged. You must obtain a clean strip with all of the wire strands intact.

Opentheharnessbyremovinganytape:



•

Use a sewing seam ripper, available from sewing supply stores, in order to cut open the harness in

order to avoid wire insulation damage.

•

Use the DuraSeal splice sleeves on all types of insulation except Tefzel and coaxial.



Cut as little wire off the harness as possible. You may need the extra length of wire in order to change the

location of a splice.

Adjust splice locations so that each splice is at least 40 mm (1.5 in) away from the other splices, harness

branches, or connectors.



Striptheinsulation:



•

When adding a length of wire to the existing harness, use the same size wire as the original

wire.

•

Perform one of the following items in order to find the correct wire size:

Find the wire on the schematic and convert to regional wiring gauge size.

If you are unsure of the wire size, begin with the largest opening in the wire stripper and work down until

achieving a clean strip of the insulation.

•

Strip approximately 5.0 mm (0.20 in) of insulation from each wire to be spliced.

•

Do not nick or cut any of the strands. Inspect the stripped wire for nicks or cut strands.

•

If the wire is damaged, repeat this procedure after removing the damaged section.



For high temperature wiring, slide a section of high

temperature SCT1 shrink tubing down the length of wire

be spliced. Ensure that the shrink tubing will not interfere

with the splice procedure.

Select the proper DuraSeal splice sleeve according to the

wire size. Refer to the above table at the beginning of the

repair procedure for the color coding of the DuraSeal

splice sleeves and the crimp tool nests.

The EL-38125-10 splice sleeve crimping tool has four crimp

nests. The largest crimp nest (4) is used for crimping 10

and 12 gauge wires. The second largest crimp nest (3) is

used for crimping 14 and 16 gauge

wires. The third

largest crimp nest (2) is used for crimping 18 and 20

gauge wires. The smallest crimp

nest (1) is used for

crimping 22 to 26 gauge wires. The crimp nests are

referenced in the table (farther

above) under the crimp

tool nest color.

Altri manuali Kicker Subwoofer

Kicker

Kicker COMP12D4 Manuale utente

Kicker

Kicker Solo-Baric S15L5 Manuale utente

Kicker

Kicker BassStation PT8 Manuale utente

Kicker

Kicker SF150S09 Manuale utente

Kicker

Kicker CompVR CVR15 Manuale utente

Kicker

Kicker KM10 Manuale utente

Kicker

Kicker COMPVT10 Manuale utente

Kicker

Kicker SSUTAYU15 Manuale utente

Kicker

Kicker TCVR10 Manuale utente

Kicker

Kicker CompR8 Manuale utente

Kicker

Kicker SOLO-BARIC DS12L3 Manuale utente

Kicker

Kicker SOLO-BARIC L7 Series Manuale utente

Kicker

Kicker SOLO-BARIC L7S12 Manuale utente

Kicker

Kicker SOLO-BARIC S10L3 Manuale utente

Kicker

Kicker L7T8 Manuale utente

Kicker

Kicker CompVX CVX10 Manuale utente

Kicker

Kicker KICKER CompVT CVT10 Manuale utente

Kicker

Kicker PTRTP Manuale utente

Kicker

Kicker SoloX S10XSP Manuale utente

Kicker

Kicker SOLOX Manuale utente

Kicker

Kicker SOLO-BARIC S15L7 Manuale utente

Kicker

Kicker CompS10 Manuale utente

Kicker

Kicker Solo-Baric D-Series Manuale utente

Kicker

Kicker SOLO-BARIC SERIES Manuale utente

Manuali Subwoofer popolari di altre marche

Sony

Sony XS-AW8 Manuale utente

Sony

Sony XS-L836 Manuale utente

B&C Speakers

B&C Speakers 15 HPL 76W Manuale utente

Velodyne

Velodyne DD-18+ Manuale utente

Sonance

Sonance Cinema Series SUB 10-150 Manuale utente

Hifonics

Hifonics HW-12 Guida rapida

Magnat Audio

Magnat Audio ADR 130 BP Manuale utente

Blitz

Blitz BZP106 Manuale utente

Technics

Technics SB-AS500 Manuale utente

Lyngdorf

Lyngdorf BW-2 Manuale utente

Lyngdorf

Lyngdorf BW-3 Manuale utente

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manuale utente

REL Acoustics

REL Acoustics Q Series Manuale utente

Pioneer

Pioneer Elite S-W1EX Manuale utente

L-Acoustics

L-Acoustics KIVA SB15M Guida rapida

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manuale utente

KEF

KEF KUBE 200 Manuale utente

Yamaha

Yamaha SW500 Manuale utente