Kidde P4010ACLEDSCOCA-2 Manuale utente

Model

P4010ACLEDSCOCA2

Hardwire Photoelectric Smoke &

Carbon Monoxide Alarm with

LED Strobe and Voice

User Guide

LED STROBE

120 V HARDWIRE

INTERCONNECT

10YEAR BATTERY BACKUP

VOICE ALARM

COMBINATION ALARM

P/N: 2562-7203-01

Thank You for Purchasing this Kidde Alarm

Hardwired for 120 V AC, this model features a non-replaceable, sealed-in battery backup. It also contains

an LED Strobe, a voice message system and Hush®Control to temporarily silence nuisance alarms.

NOTE: Battery backup supplies power to the smoke and carbon monoxide alarm portions only. Strobe

will not work without AC power.

Teach children how to respond to the alarm and that they should never play with the unit. This alarm is a

multi-criteria device designed to detect both smoke and carbon monoxide from any source of combustion in

a residential environment. It is not designed for use in a recreational vehicle (RV) or boat.

NOTE: Please take a few minutes to thoroughly read this user guide which should be saved for future

reference and passed on to any subsequent owner.

The National Fire Protection Association (NFPA) and the manufacturer recommend replacing this alarm ten

years from the date code on back of alarm.

Date Code (on back): ___________________

Date of Purchase: ___________________

Where Purchased: ___________________

Date to Replace: ___________________

Product Support: 1-800-880-6788

Please write down the below information

and have this at hand when you call.

Contents

1. Smoke Alarm: What To Do When The Alarm Sounds . . . . . . . . . . 4

2. Carbon Monoxide Alarm: What To Do When The Alarm Sounds . . . . . . 5

3. Other Alarm Visual And Audible Indicators . . . . . . . . . . . . . .6

4. Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . 7

5. Introduction, Product Features & Specifications . . . . . . . . . . . . 8

6. Limitations Of Smoke And Carbon Monoxide Alarms . . . . . . . . . . 10

7. Recommended Locations . . . . . . . . . . . . . . . . . . . . 12

8. Locations To Avoid . . . . . . . . . . . . . . . . . . . . . . .15

9. Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . 16

10. Operation And Testing . . . . . . . . . . . . . . . . . . . . . 19

11. Recognizing Nuisance Alarms . . . . . . . . . . . . . . . . . . 21

12. Battery Back Up . . . . . . . . . . . . . . . . . . . . . . . . 22

13. Permanently Disable Alarm / Discharge Battery . . . . . . . . . . . . 23

14. General Carbon Monoxide (CO) Information . . . . . . . . . . . . . 24

15. Cleaning Your Alarm . . . . . . . . . . . . . . . . . . . . . .27

16. Good Safety Habits . . . . . . . . . . . . . . . . . . . . . . 28

17. Service And Warranty . . . . . . . . . . . . . . . . . . . . . 32

1. Smoke Alarm: What To Do When the Alarm Sounds

Smoke alarm pattern is three long beeps with voice “Fire!,” a 1.5 second pause, and three long beeps repeating.

The red LED blinks in time with alarm pattern, and the Strobe flashes every second.

The smoke alarm takes precedence when both smoke and carbon monoxide are present.

•Alert small children in the home as well as anyone else that might have difficulty recognizing the

importance of the alarm sounding or that might have difficulty leaving the area without help.

•Leave immediately by your escape plan. Every second counts, so don’t waste time getting dressed or

picking up valuables.

•In leaving, don’t open any inside door without first feeling its surface. If hot, or if you see smoke seeping

through cracks, don’t open that door! Instead, use your alternate exit. If the inside of the door is cool,

place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke rush in.

•If the escape route requires you to go through smoke, stay close to the floor where the air is cleaner.

Crawl if necessary, and breathe shallowly through a cloth, wet if possible.

•Once outside, go to your selected meeting place and make sure everyone is there.

•Call the fire department from your cell phone outside, or from your neighbour’s home—not from yours!

•Don’t return to your home until the fire officials say that it is all right to do so.

•There are situations where a smoke alarm may not be effective to protect against fire as stated in the

NFPA Standard 72. For instance:

a) smoking in bed

b) leaving children home alone

c) cleaning with flammable liquids, such as gasoline

NOTE: See Section 11. RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Carbon Monoxide Alarm: What To Do When the Alarm Sounds

Carbon monoxide (CO) alarm pattern is four quick beeps with voice “Warning! Carbon Monoxide” repeating

every 5 seconds. The red LED blinks in time with alarm pattern. The Strobe will flash 4 times every 5 seconds.

warning: Carbon monoxide alarm aCtivation indiCates the presenCe

of Carbon monoxide (Co) at high ConCentrations whiCh Can kill you.

1. Immediately move to fresh air – outdoors or by an open door/window. Do a head count to check that

all persons are accounted for. Do not re-enter the premises or move away from the open door/window

until the emergency services responders have arrived, the premises have been aired out, and your

alarm remains in its normal condition.

2. Call your local emergency service.

(fire department or 911)

Never restart the source of a CO problem until it has been corrected. Never ignore the activation of the

alarm!

NOTE: See Section 11. RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

PHONE NUMBER

3. Other Alarm Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal (standby) AC power: Green LED on continuously

during light conditions, or blink every

60 sec during dark conditions.

DC power: Green LED blink approx

every 60 sec.

Test (button press when

no alarm condition is

present)

• 4 patterns of Red/Amber/Green.

• Test: Red LED blinks in time with alarm

pattern. Strobe ashes every second

during smoke alarm, and 4 times every

5 seconds during CO alarm.

• Green LED fade on/o at test complete

• Button press sound

• Voice: "Testing, this is very loud.

Press now to cancel test. 5, 4, 3, 2, 1."

• 3 long beeps, Voice "Fire!",

3 long beeps, 4 quick beeps, Voice

"Warning, Carbon Monoxide,"

4 quick beeps, Voice "Test

Complete," Power on/reset sound.

• Voice "Test Canceled" if button

pushed before test sequence

begins.

Perform Test/Hush button press

once a week to verify proper alarm

operation

* Push/release button before the

countdown ends to cancel test.

Smoke or CO Alarm

Memory (unit has

experienced a smoke or

CO alarm event within the

last hour)

Red and Amber LED alternate on 1 sec,

every 10 sec.

After button push: "Smoke previously

detected" or "Carbon Monoxide

previously detected" only on the

initiating alarm unit.

Push test button to clear Alarm

Memory. NOTE: standard test

sequence will follow. (Push/release

button again to cancel test).

Smoke Alarm Hush Mode,

(Hush®

Control)

Red LED blinks every 2 sec. After button push: "Hush Mode Acti-

vated." Smoke alarm pattern stops.

(If there is too much smoke to allow

Hush: Voice "Too Much Smoke, Alarm

cannot be Hushed" Smoke alarm

pattern continues.)

This feature is to be used only

when a known alarm condition,

such as smoke from cooking,

activates the alarm.

CO alarm reset None After button push: CO alarm pattern

stops.

Unit is conrming if CO is present

or if it experienced a nuisance

situation. Re-alarm means danger.

Move to fresh air and call 911.

Smoke Alarm Hush Mode

Canceled

None Voice message "Hush Mode

Canceled."

When smoke levels drop below the

alarm threshold, the voice message

"Hush Mode Canceled" will occur .

Initiating Alarm,

(Multiple alarms in an

interconnected system)

Green LED blinks once per sec indicating

that this is the unit initiating the alarm

in an interconnected, multiple alarm,

system. Strobe ashes in smoke or CO

alarm pattern.

Unit in either Smoke or CO alarm

mode.

During alarm, the Initiating alarm

green blinks will occur in between

the red blinks.

4. Troubleshooting Guide

Trouble Condition Visual Indications Audible Indications Action:

False Low Battery

(AC power connected

before backup battery

activated)

Amber

LED

blinks

every

seconds

Chirp every 60 sec, voice every 30

sec: "Activate Battery."

Voice stops after 5 mins.

Rotate the alarm onto the mounting bracket to activate

backup battery.

Low Battery Chirp every 60 sec, voice every

30 sec: “Replace alarm.”

Voice stops after 5 mins.

* Remove, discharge, dispose unit, and replace as soon

as possible.

Fault Mode Chirp every 30 sec.

Voice every 30 sec: “Error, see trouble

shooting guide”

After 5 mins: no voice message

* See Cleaning Your Alarm section.

* Push Test/Hush button once to attempt to reset

the unit .

* Red LED will blink out an error code (number of blinks)

when Test/Hush button is push/released once. Report

the number of blinks to customer service if needed.

End of Unit Life Double chirp every 30 sec.

First 5 mins: Voice every 30 sec:

“Replace alarm, press button to

temporarily silence.” Voice stops after

5 mins. After 7 days: Chirps continue.

Voice every 30 sec for 5 mins:

“Replace alarm.”

* Push/release Test/Hush button to temporarily silence

(see End of Unit Life Hush Mode section below)

* Remove, discharge, dispose unit, and replace as soon

as possible.

End of Unit Life Hush

Mode (after push/

release Test/Hush

button during End

of Life)

Voice “Temporarily Silenced.”

End of Unit Life chirps silenced for

24 hrs. (7 days after End of Unit Life

chirps begin, the chirps cannot be

silenced.)

* Remove, discharge, dispose unit, and replace as soon

as possible.

If you require further information please contact Product Support at 1-800-880-6788 or write us at:

Kidde Canada Inc., P.O. Box 40, Apsley, ON K0L 1A0. Our internet address is www.kiddecanada.com.

5. Introduction, Product Features and Specifications

INTRODUCTION

This alarm detects products of combustion using photoelectric technology and carbon monoxide using an

electrochemical cell. Many times throughout this User Guide, we will refer to Carbon Monoxide as “CO.” Ten (10)

years after the unit is installed, this unit will automatically alert you that it is time to replace the unit. This is called

“End of Unit Life” mode. See Troubleshooting Guide. To help identify the date to replace the unit, a label has

been affixed to the side of the alarm. Write in the “Replace by” date (10 years from initial power up) in permanent

marker on the label prior to installing the unit.

NOTE: AC power must be connected to obtain the full 10 year battery and unit life.

PRODUCT FEATURES AND SPECIFICATIONS:

•Temperature: Operating Range: 4.4°C (40°F) to 37.8°C (100°F)

•Humidity: Operating range: 10-95% RH non-condensing

•Audible Alarm: 85+ dB at 10’ 3.0 to 3.5 KHz pulsing alarm, with voice messages

“Fire!” and/or “Warning! Carbon Monoxide.”

•Smoke Sensor: Photoelectric

•CO Sensor: Electrochemical

•LED Strobe

•Voice message system

•Smoke Alarm Hush®Control

•Ambient Light Sensing

•Powered by 120 V AC (60 Hz, 687 mA max) wire-in connector with sealed lithium battery backup.

•Hardwire interconnectable to other compatible alarms.

•One large, user- friendly button. (Strobe dome is the button)

•Applications: Primary Direct or Indirect and Supplementary

•Light Output: 177 Candela minimum (on axis measurement)

Permanently Disable

Alarm / Discharge

Battery

AC Connector

PRODUCT FEATURES AND SPECIFICATIONS:

Test / Hush

Button (dome)

Red Alarm

Light

Green Operate

Light

Alarm Sounder

CEILING

90° 90°

0°

45°45°

SOURCE

LIGHT

CEILING

90° 90°

0°

45°45°

SOURCE

LIGHT

25 90

25 85

30 80

30 75

35 70

35 65

40 60

45 55

55 50

75 30-45

90 5-25

100 0

(LIGHT INTENSITY) (IN DEGREES)

PERCENT ANGLE

25 90

25 85

30 80

30 75

35 70

35 65

40 60

45 55

55 50

75 30-45

90 5-25

100 0

(LIGHT INTENSITY) (IN DEGREES)

PERCENT ANGLE

90° 60 55 50 45 40 35 30

ZERO AXIS

WALL

FLOOR

Front Back

The following diagrams show that the light intensity gradually decreases as the viewing angle is

increased. Use this information to determine the best location for the strobe light.

6. Limitations of Smoke and Carbon Monoxide Alarms

WARNING: PLEASE READ CAREFULLY AND THOROUGHLY

•Life safety from fire in residential occupancies is based primarily on early notification to occupants of the

need to escape, followed by the appropriate egress actions by those occupants.

•Fire warning systems for dwelling units are capable of protecting about half of the occupants in

potentially fatal fires. Victims are often intimate with the fire, too old or young, or physically or mentally

impaired such that they cannot escape even when warned early enough that escape should be possible.

For these people, other strategies such as protection-in-place or assisted escape or rescue are necessary.

•Leading authorities recommend that both ionization and photoelectric smoke alarms be installed to

help insure maximum detection of the various types of fires that can occur within the home. Ionization

sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner than

photoelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated with slow

smoldering fires) sooner than ionization alarms.

•A battery powered alarm must have a battery of the specified type, in good condition and installed

properly (This model has a sealed backup battery).

•Smoke alarms must be tested regularly to make sure the battery and the alarm circuits are in good

operating condition.

•Smoke alarms cannot provide an alarm if smoke does not reach the alarm. Therefore, smoke alarms may

not sense fires starting in chimneys, walls, on roofs, on the other side of a closed door or on a different

floor.

•If the alarm is located outside the bedroom or on a different floor, it may not wake up a sound sleeper.

•The use of alcohol or drugs may also impair one’s ability to hear the smoke alarm. For maximum

protection, a smoke alarm should be installed in each sleeping area on every level of a home.

Indice

Altri manuali Kidde Sistema di sicurezza

Kidde

Kidde KN-COB-B Manuale utente

Kidde

Kidde ZP885 Istruzioni per il montaggio

Kidde

Kidde KF10 Manuale utente

Kidde

Kidde KN-COPE-D Manuale utente

Kidde

Kidde 4MCO Manuale utente

Kidde

Kidde KN-COB-DP-H) Manuale utente

Kidde

Kidde KN-COP-DP-B Manuale utente

Kidde

Kidde 2030-DCR Istruzioni per l’uso

Kidde

Kidde 7CO Manuale utente

Kidde

Kidde KN-COP-DP-10YHCA (900-0284CA) Manuale utente

Kidde

Kidde P4010ACSCOAQ-WF Manuale utente

Kidde

Kidde SLED177iCA Manuale utente

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Manuale utente

Kidde

Kidde KN-COB-IC Manuale utente

Kidde

Kidde KN-COB-IC Manuale utente

Kidde

Kidde KN-COPP-B-LS Manuale utente

Kidde

Kidde P4010ACSCO-WF Manuale utente

Kidde

Kidde 900-CUAR Manuale utente

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Manuale utente

Kidde

Kidde Truesense Combo Manuale utente

Kidde

Kidde SLICK RF-SFTP Manuale utente

Kidde

Kidde WFPCO Manuale utente

Kidde

Kidde KF30 Manuale utente

Kidde

Kidde KN-COB-IC-CA Manuale di istruzioni

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente