King Industrial KC-60FX Manuale utente
6’’ WOODWORKING
JOINTER
INSTRUCTION MANUAL
MODEL: KC-60FX
COPYRIGHT 2000 BY KING CANADA TOOLS INC.
GENERAL SAFETY RULES
W
WA
AR
RN
NI
IN
NG
G:
:Do not attempt to operate until you have read thouroughly
and have understood all instructions, rules ect. contained in this manual.
Failure to comply can result in accidents involving fire, electric shock,
or personal injury. Keep owners manual and review frequently for
continuous safe operation.
1. KNOW YOUR MACHINE.
For your own safety, read the owner’s manual cafefully. Learn its application and limitations
as well as specific potential hazards pertinent to this machine.
2. GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT
WITH GROUNED SURFACES.
3. REMOVE ADJUSTING KEYS AND WRENCHES.
Form a habit of checking to see that keys and wrenches are removed from
the machine before turning it on.
4. KEEP WORK AREA CLEAN.
Cluttered areas invite accidents.
5. DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp or wet locations, or expose them to rain. Keep work
areas well illuminated.
6. KEEP CHILDREN AWAY.
All visitors should be kept at a safe distance from work area.
7. MAKE WORKSHOP CHILDPROOF.
With padlocks, master switches, or by removing starter keys.
8. DO NOT FORCE THE MACHINE.
It will do the job better and be safer at the rate for which it was designed.
9. USE THE RIGHT TOOLS.
Do not force the machine or attachments to do a job for which they were not designed.
10. WEAR PROPER APPAREL.
Avoid loose clothing, gloves, neckties, rings, bracelets, or jewelry which could be
caught in moving parts. Nonslip footwear is recommended. Wear protective hair
covering to contain long hair.
11. ALWAYS WEAR SAFETY GLASSES.
Always use face or dust mask if operation is dusty. Everyday eyeglasses only have
impact resistant lenses. They are NOT safety glasses.
12. SECURE WORK.
Use clamps or a vise to hold work when practical. It is safer than using your hand
and frees both hands to operate the machine.
13. DO NOT OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN MACHINE IN TOP CONDITION.
Keep machine clean for best and safest performance. Follow instructions for
lubricating and changing accessories.
15. DISCONNECT THE MACHINE FROM POWER SOURCE.
Before servicing and when changing accessories, or when mounting and
remounting motor.
16. USE RECOMMENDED ACCESSORIES
Consult the owners manual for recommended accessories.
17. CHECK DAMAGED PARTS.
Before further use of the machine, the guards and other parts should be carefully
inspected to ensure it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, mounting, and any other
condition that may affect its operation. Guards and other parts that are damaged
should be properly repaired or replaced.
18. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
SAFETY RULES FOR JOINTERS
1. KEEP cutterhead sharp and free of all rust and pitch.
2. ALWAYS use a push block when jointing stock that does not give reasonable distance
of safety for your hands.
3. NEVER pass hands directly over the cutterhead.
4. ALWAYS make sure exposed cutterhead behind the fence is guarded, especially
when jointing near the edge.
5. DO NOT perform jointing or planing operations on material shorter than 8 inches,
narrower than 3/4 inch, or thinner than 1/2 inch.
6. MAINTAIN the proper relationship between the infeed and outfeed table surfaces and
cutterhead knife path.
7. SUPPORT the workpiece adequately at all times during operation, maintain
control of the work at all times.
8. DO NOT back the workpiece towards the infeed table.
9. DO NOT attempt to perform abnormal or little-used operations without study and use
of adequate holddown/push blocks, jigs, fixtures, stops, etc..
10. DO NOT make cuts deeper than 1/8’’ in a single pass. On cuts more than 1/2’’ wide,
adjust depth of cut to 1/16’’ or less to avoid wood tearing.
UNPACKING THE MACHINE
1. Cafefully unpack the machine.
2. Check to see if there is any damage which occured to the machine during transportation.
Report to your local distributor if there is damage.
3. Check to see if there are any parts missing. If so, contact your local distributor.
CLEANING THE MACHINE
1. The machine has been coated with a rust protection oil for transportation purposes.
2. Thoroughly remove the oil coating after unpacking the machine.
3. Use kerosene to remove the oil coating. Do not use gasoline or paint thinner to remove
the oil coating, as this may damage the painted surfaces.
LEGEND OF THE MACHINE
1. Outfeed Table Adjustment Handwheel.
2. Outfeed Table.
3. Fence.
4. Fence Movement Fix Lever.
5. Fence Angle Adjustment Lever.
6. Depth Scale.
7. Lever.
8. Cutterhead Guard.
9. Spring Knob.
10. Infeed Table.
11. Infeed Table Adjustment Handwheel.
12. Base.
13. Power Switch.
14. Enclosed Floor Stand.
1
2
3
4
5789
10
11
12
13
14
6
SPECIFICATIONS
Cutting Capacity Width...................................6-1/8’’ (155mm)
Cutting Capacity Depth......................................1/2’’ (12.7mm)
Rabbeting Capacity.............................................1/2’’ (12.7mm)
Cutterhead:
Cutterhead Speed.................................................5,000 R.P.M.
Cuts per Minute..............................................................15,000
Number of Knives....................................................................3
Diameter................................................................2.4’’ (61mm)
Table:
Dimensions...............................7.3’’ (185mm) X 45’’ (1143mm)
Height................................................................32.3’’(820mm)
Fence:
Dimensions...................................4’’ (102mm) X 28’’ (710mm)
Tilts Right..............................................................................450
Positive Stops................................................................900, 450
Overall Dimensions:
Length.................................................................45’’ (1143mm)
Height............Enclosed Steel Stand.................36.6’’ (930mm)
Net Weight......................................................198 lbs. (90 kgs)
LOOSE PARTS BAG
1. Stand Mounting Screws with Washers................................3 pcs.
2. Open End Wrench...........................8 X10 (1 pc.), 12 X14 (1 pc.)
3. Screwdriver............................................................................1 pc.
4. Belt Guard Lock Screw...................................1/4’’ X 3/4’’ (4 pcs.)
5. Allen Wrench............................................................3mm (1 pc.)
6. Belt Guard..........................................................................1 pc.
6
POWER CONNECTIONS
Set aside an electrical circuit that is used exclusively for tools. It should be at least a #12 wire
and protected with a 15 AMP time lag fuse. Before connecting the motor to the power source,
make sure that the voltage is the same as indicated on the machine, and that the machine is
turned off. Check all connections for good contact. WARNING: If the machine runs on
insufficient voltage, damage to the motor may occur.
GROUNDING
Failure to adequately ground the machine may result in electric shock to the operator. Always
use a three prong extension cord and outlet. If there is any doubt that the outlet is not grounded
properly, have it checked by a certified electrician. Only use three to two adapters temporarily.
EXTENSION CORDS
Check the condition of the extension cord regularly. Use a three wire extension cord with a
three prong plug, and make sure it is plugged into an appropriate three hole receptacle. If you
must use a two prong adapter temporarily, make sure the grounding extension on the adapter
is connected to a permanent ground. Do not bend the grounding plug to fit it into a two hole
receptacle. Remember to use a cord heavy enough to carry the jointer’s current. If the cord
length is under 25 feet for 110V operation, and under 50 feet for 220V operation, use at least
a 14 AWG gauge extension cord. If the cord length is between 25 and 50 feet for 110V
operation, and between 50 and 100 feet for 220V, use at least a 12 AWG gauge extension cord.
Do not use cords longer than 50 feet and 100 feet for 110V and 220V operations respectively.
CHANGING VOLTAGE
This machine is set up at the factory for 110V
use. To change the voltage to 220V, disconnect
the machine from its power source and follow
the electrical diagram as shown below.
SWITCH WIRING DIAGRAM
STARTING AND STOPPING
THE JOINTER
1. The machine switch is located at the right
side of the machine.
2. Press the ‘ON’ switch to start the machine.
3. Press the ‘OFF’ switch to stop the machine.
DEPTH OF CUT
ADJUSTMENT
1. To set the depth of cut, move the infeed table
up and down.
2. The table can be moved by turning the
depth adjustment handwheel (A) under
the table.
3. Loosen the outfeed table position fix lever
before turning the depth adjustment
handwheel (A). Tighten the infeed table
position lock fix lever (B) after the infeed
table is adjusted.
4. The depth of cut adjustment can be read
on the depth scale (C), located at the
front of the infeed table.
DEPTH SCALE (C)
DEPTH ADJUSTMENT HANDWHEEL (A)
FIX LEVER (B)
Indice
Altri manuali King Industrial Utensili elettrici
King Industrial
King Industrial KC-116C Manuale utente
King Industrial
King Industrial KC-366SH Manuale utente
King Industrial
King Industrial KC-70FX Manuale utente
King Industrial
King Industrial KC-32VS Manuale utente
King Industrial
King Industrial KC-119FC-LS Manuale utente
King Industrial
King Industrial KC-70FX Manuale utente
King Industrial
King Industrial KC-117C Manuale utente
King Industrial
King Industrial KC-15HS-VS Manuale utente
King Industrial
King Industrial KC-EB100 Manuale utente
King Industrial
King Industrial KRT-100 Manuale utente
King Industrial
King Industrial KC-118FC Manuale utente
King Industrial
King Industrial 8" Jointer KC-203C Manuale utente
King Industrial
King Industrial KC-6HJC Manuale utente
King Industrial
King Industrial 12" Industrial Jointer KC-125FX Manuale utente
King Industrial
King Industrial KC-12HJPC Manuale utente
King Industrial
King Industrial KC-351S Manuale utente
King Industrial
King Industrial KC-4900S Manuale utente
King Industrial
King Industrial KC-10HJC Manuale utente
King Industrial
King Industrial MA-1050ST Manuale utente
King Industrial
King Industrial KC-122FC Manuale utente
