KING Extend KX3000 Manuale utente
KX1000
LTE/CELL SIGNAL BOOSTER
powered by weBoost®
User Manual
EXTEND
Page 2
BEFORE YOU START
Read through this manual before installing
or operating the KING Extend.
If you have any questions,
call KING Customer Service at (952) 345-8147.
! !
CONTENTS
CONTENTS
CONTENTS ................................................................................................. 2
IMPORTANT POINTS ................................................................................. 3
COMPONENT LOCATIONS ....................................................................... 4
OUTSIDE ANTENNA MOUNTING OPTIONS ............................................ 5
INSTALLATION ....................................................................................... 6-7
MEASURING BOOSTER PERFORMANCE ........................................... 8-9
SIGNAL BOOSTER STATUS LIGHT ....................................................... 10
TROUBLESHOOTING .............................................................................. 11
SPECIFICATIONS ............................................................................... 12-13
SAFETY GUIDELINES ............................................................................. 14
WARRANTY .............................................................................................. 15
Page 3
Do not put sharp bends in coax cables.
This can reduce signal strength from the antenna.
IMPORTANT POINTS
The installer is responsible for determining the most appropriate
fasteners to secure the antenna bracket to the roof. Depending on
the roof material, fasteners such as lag screws, well nuts, sheet metal
screws, toggle bolts and T anchors may be used, and should always be
used in combination with a roof-compatible sealant.
The installer is responsible for properly securing the coax cable to the
roof (for example, cable ties and cable tie mounting pads).
heads with roof-compatible sealant.
You will need a drill and drill bit, roof-compatible sealant and appropriate
fasteners to install all components and wiring.
IMPORTANT! The aluminum casing of your signal booster will adjust to the
temperature of its environment, but is designed to protect the signal booster
technology. For example, in the summer, the signal booster case may be
as hot as 150 degrees inside your vehicle. These high temperatures will not
be sure to place your signal booster in a location with adequate ventilation
and away from direct sunlight or moisture.
The signal booster may remain on in vehicles whose 12V DC power sources
do not automatically shut down when the vehicle is turned off. This could
result in discharging the vehicle’s battery in one to two days.
overlap, a condition called oscillation occurs. Oscillation can be thought of as
noise, which causes the booster to shut down to prevent damage. The best
way to keep these spheres of signal from overlapping is to maximize separation
between the booster and the antenna.
Page 4
COMPONENT LOCATIONS
NOTE: It is up to the installer to determine the best component locations.
components in their chosen locations, completing the setup
instructions, and verifying the system works as desired.
(Route the cable through an open door or window for the
soft install.)
TIP
Page 5
OUTSIDE ANTENNA MOUNTING OPTIONS
Page 6
1. Fasten the outside antenna to the mounting bracket with the supplied
screws and washers (see page 5).
2. Connect the separate 20’ cable to the antenna (LARGE CONNECTOR).
will penetrate the roof.
4. Fasten bracket to roof. Make sure fastener holes and fastener heads are
properly sealed.
INSTALLATION
Page 7
If using the included booster
mounting bracket, remove
the booster from the bracket.
Fasten bracket to wall, then
snap booster back into bracket.
TIP
5. Route the cable to where it will enter the vehicle.
6. Drill an appropriately sized hole and feed the cable into the vehicle.
7. Seal the roof hole so it is completely waterproof (inside and outside).
8. Inside, place booster in desired location or install the booster to wall.
Connect cable to booster.
9. Connect inside antenna cable to booster and place inside antenna in
position.
10. Plug booster into power source.
IMPORTANT! Make sure to avoid any cabling, pipes, etc. that may be
damaged by drilling.
Page 8
Note it here:
MEASURING BOOSTER PERFORMANCE
Dial *3001#12345#* then press Call.
1
2 Release the power button.
3 Hold the Home button until your main screen
appears.
If you want to check 3G/1x but your iPhone is picking up
4G/LTE signal , go to Settings>Cellular>Cellular Data
Options>Enable LTE>Select Off.
signal by once again dialing *3001#12345#* then pressing
left corner of your phone.
as placing calls in different locations. For changes/updates
on this issue, periodically go to weboost.com/signalstrength.
Network Type and Strength (exact options/wording depends
on phone model).
iPhone®
iPhone®
IOS 11 - current
Android™
Page 9
All Other Phones and Alternate Methods
• https://www.weboost.com/test-mode-instructions/
All Phones:
• Keep track of the network (3G or 4G) the phone is connected to.
readings from other carriers, you will need phones from each carrier.
by dialing *3001#12345#* and pressing Call. Press the signal strength at
the top left of the screen to toggle between numbers and bars. Press the
Home button to exit Field and Test mode.
Compare Results
Having an accurate measurement of signal strength in decibels (dBm)
is crucial when installing your system. Decibels accurately measure the
signal strength you are receiving.
Did you know a signal increase of just 3dB is 2 times the power of signal
Page 10
SIGNAL BOOSTER STATUS LIGHT
SOLID GREEN
This indicates your booster is functioning properly and there are no issues
with installation.
BLINKING RED, THEN SOLID GREEN
This indicates one or more of the booster bands has reduced power due to
a feedback loop condition called oscillation. This is a built-in safety feature
to prevent harmful interference with a nearby cell tower. If you are already
experiencing the desired signal boost, then no further adjustments are
necessary. If you are not experiencing the desired boost in coverage, then
refer to the troubleshooting section on the next page.
SOLID RED
This is due to a feedback loop condition called oscillation. This is a built-in
safety feature that causes a band to shut off to prevent harmful interference
with a nearby cell tower. Refer to the troubleshooting section on the next
page.
LIGHT OFF
If the signal booster light is off, verify your power supply has power.
NOTE: The signal booster can be reset by disconnecting and reconnecting the
power supply.
then reconnecting power to the signal booster.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali KING Estensione
