KingKong FPVEGG PRO Manuale utente
Instruction Manual
Feature
* FPVEGG PRO used CCD600 camera(1/3 SONY CCD)
* The structure uses 4.0mm thick carbon fiber and 7075 aviation aluminum
alloy material, light weight, high strength.
* Product performance and wheelbase for indoor through the special design.
* BLheliS 4in1 20A ESC ,support MULTISHOT,ONESHOT and DSHOT provedes
a better user experience.
* Modular design, KK TOWER FC(F4+OSD), with the betaflight firmware.
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 1
FPVEGG PRO Configuration
FPVEGG PRO Package list
PNP*1 3050 Prop*10Pairs Battery*1
Rubber*2
Instruction manual*1
mackintosh*4 Tie*5
Wheelbase:138mm
Input voltage:3~4S Lipo
KK TOWER(2 Layer) 20*20:
F4+OSD
4in1 20A BLheliS
VTX:Q100 VTX(25mW/100mW 16CH)
Camera:CCD600 (600TVL CCD 160 NTSC)
Motor:XT1406-3600KV
Prop:3050
Battery:11.1V 850mAh 45C
Weight:129.5g(without receiver and battery)
FPVEGG PRO(with buzzer and LED)
The package includes 3S lipo,If you want to fly more powerful, you need buy 4S lipo (650-850mAh) on your own.
The package not includes receiver,you need buy high quality receiver(S.BUS/PPM/DSM2) on your own.
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 2
FC
Front Back
ESC
VTX
Motor
M4(CW) M2(CCW)
M3(CCW) M1(CW)
+-
Power 2~4S
M1
M2
M3
M4
4.0V VIN GND VIDEO
25mW
100mW
-+
-
+VIN 2S-4S Lipo
7V-18V
GND
LED Frequency table
Click the key change frequency point
Please attention ventilation cooling
Antenna Q100-Mini 25mW/100mW 16CH VTX (2S-4S Lipo 7V-18V)
L=28mm,W=11mm,Weight=2.5g(Without camera and wire)
Note:pay attention to the direction of rotation of the motor
when installing the prop
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 3
Receiver
3V3 RC IN GND5V+
VIDEO
VTX
Connect these 3
pads to VTX when
use 2L tower(FC+ESC)
GND5V+
3V3 RC IN GND
RC IN GND5V+
DSMX
S.BUS/PPM
LED+Buzzer
5V(BUZZER+) LED(S) GNDBUZZER-
Camera
5V+ GND VIDEO AUDIO
USB
BOOT
USB
Receiver
XM Receiver example
FS-RX2A Receiver example
XM bind (default S.BUS),example(FRSKY X9D)
1. Open remote control, set D16 mode.
2. Hold receiver bind button to power, loosen until red and green light constant lighting.
3. Open remote control Bind, press “Enter” and wait a few seconds, then stop Bind when red light flash and green light
constant lighting.
4. Disconnect receiver power and power-on again, green light constant lighting means bind success.
.
.
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 4
FM800 Receiver example
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 5
Please select MULT
Product and Part code
Name
FPVEGG PRO PNP
FPVEGG PRO KIT
3050 Prop
Battery 11.1V 850mAh 45C
Carbon fiber plate(FPVEGG PRO part)
Q100 VTX
PLASTIC CARRYING CASE
KK TOWER WIRE
Factory Code
PNP.FPVEGG PRO
KIT.FPVEGG PRO
PROP.3050.3
BAT.11.1V 850MAH 45C
VTX.Q100
PART.PLASTIC CARRYING CASE
PART.KK TOWER WIRE
Factory Code
MOTOR.XT1406-3600KV
FLYTOWER.KK TOWER(2 LAYER) 20A
ESC.KK TOWER 20A
FC.KK TOWER(F4+OSD)
PART.FPV EGG 7075 ALUMINUM FRAME
CAM.CCD600
PART.KK TOWER SCREW(2 LAYER)
Name
XT1406-3600KV
KK TOWER(2 LAYER) 20A
KK TOWER ESC(20A)
KK TOWER FC(F4+OSD)
FPV EGG 7075
Aluminum frame
CCD600 Camera
KK TOWER SCREW(2 LAYER)
PART.BOTTOM PLATE.FPVEGG PRO
DSM2 Receiver example
LDARC FPVEGG PRO Instruction M anual 2017-11-27 8 Pages-Page 6
OMNIBUSF4SD
3.2.1- OMNIBUSF4SD -18-10-2017 03:31(stable)
6.PID Default setting
Connect
BETAFLIGHT firmware allready flash before leave the factory,user just need
connect PC to adjust the parameter.
1.Open betaflight configurator ,then click ,select FW version
2.Click , then click to download FW to FC,
click after FW updating finish into settings menu.
5.Default setting of receiver is 5th channel ARM,6th channel mode switching.
Firmware update
3.Setting,select , select ESC/Motor Feature,then select DSHT600，then open
(LED_STRIP,OSD,DYNAMIC_FILTER).
4.Buzzer setting,select ，then open VBAT
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 7
After sale service
1.Provide free reparation service when find the product defect after purchase.
2.Provide pay-needed reparation service when product damage because improper operation.
3.China customers please contact with the after-sales service,overseas client please contact the dealer.
PNP/RTF Test report ID :
Flight test
Transmitter functions properly
Flying in good condition
Camera OK
VTX OK
QC:
Package check
PNP
RTF
Frame
Transmitter
ID is the same
All parts of the installation
Insulating sleeves have been installed manual
Complete accessories,total packages
QC:
LDARC FPVEGG PRO Instruction Manual 2017-11-27 8 Pages-Page 8
Altri manuali KingKong Quadricottero
