KingKutter S-ATV-180-U Manuale utente
PO Box 1200
305 Commerce Drive
Winfield, Alabama 35594
www.kingkutter.com
S-ATV-180-U
OPERATIONAND PARTS
MANUAL
3
TO THE PURCHASER
This manual contains valuable information about your
new King Kutter ATV Spreader. It has been carefully pre-
pared to give you helpful suggestions for operating, adjust-
ing, servicing and ordering repair parts.
Keep this manual in a convenient place for quick and
easy reference. Study it carefully. You have purchased a
dependable and sturdy spreader, but only by proper care
and operation can you expect to receive the service and
long life designed and built into it.
Sometime in the future your spreader may need new
parts to replace those that are worn or broken. If so, go to
your dealer and provide him with the model and part num-
ber.
Customer Information
Name_______________________________________________
PurchasedFrom______________________________________
DatePurchased______________________________________
ModelNo.___________________________________________
SerialNo.___________________________________________
4
It is the purchaser and/or operator’s responsibility to….
zz
zz
zRead and understand the information contained in
this manual.
zz
zz
zOperate, lubricate, assemble and maintain the equip-
ment in accordance with all instructions and safety
procedures in this manual.
zz
zz
zInspect the equipment and replace or repair any parts
that are damaged or worn which under continued op-
eration would cause damage, wear to other parts, or
cause a safety hazard.
zz
zz
zReturn the equipment or parts to the authorized King
Kutter dealer, from where it was purchased, for ser-
vice or replacement of defective parts that are covered
by warranty. (The King Kutter Factory may inspect
equipment or parts before warranty claims are hon-
ored.)
zz
zz
zPayment of all costs incurred by the dealer for travel-
ing to or transporting the equipment for warranty
inspection and or claims.
5
CONTENTS
ITEM PAGE
General Information.................................................6
Technical Data ..........................................................8
Safety Information....................................................9
Operating Instructions...........................................13
Safety Decal's And Locations ...............................14
Spreader Use & Adjustments ................................15
Hopper Loading .....................................................18
General Maintenance .............................................20
Lubrication .............................................................21
Replacement Parts .................................................22
Warranty ..................................................................24
6
INFORMATION ON THE MACHINE
The models in this manual have been designed and made exclusively allowing
the distribution of solid, granular fertilizers and seeds in the field. Their use is
particularly made for gardening and golf courses but can be used in many more
places. These machines are usually used in daylight. If you need to use the
spreader at night or poor visibility, you must use the lighting system of your trac-
tor or some other source to operate safely.
A use different from described above is considered improper. Any modification
made to the machine relieves the manufacturer from any responsibility of dam-
ages or injury that can be caused to operators, third parties, objects or the
spreader.
NAME PLATE
On the hopper of every spreader is a nameplate,which has the model number,
serial number and bar code of your machine. When parts are required, it is nec-
essary to refer to the plate for the model of spreader.
CHARACTERISTICS OF THE SPREADER
The pull type spreader has a fertilizer distributor made of stainless steel, a
spreader disc with (4) adjustable vanes with (4) different settings, in order to
obtain the maximum spreading precision and uniformity in the distribution, de-
pending on the material to be spread.
7
The feeding of the disc is by gravity through an opening located at the bottom of
the hopper, inside of which a mix/agitator is applied, in order to prevent forma-
tion of lumps in the fertilizer. A plate is put in front of the disc to prevent the
speading to the front side of the machine.
The fertilizer delivery is controled by properly opening the shutters in the hopper
bottom, through locking devices operated by levers. The fertilzer spreader and
the agitator are connected through a gearbox with the wheels, so the speed of
the disc is proportionate to the speed of the machine. The switching off and on
of the spreading disc is made by putting or removing the split pin on the axle.
The machine is connected with a ball hitch 1-7/8”.
There is an adjustable tongue so the height
can be adjusted to keep the spreader parallel
with the ground.
The hardness of the steel welded frame, together with the remarkable life of the
hopper, helps to obtain a highest quality level of the pull type spreaders. The
painting is made by an epoxy varnish with successive backing at 150 degrees
celsius with the application of the primer bath, assuring great protection and long
life of the machine.
8
A. REGULATING LEVER
B. HOPPER
C. DISTRIBUTOR VANES
D. SPREADER DISC
E. STEEL FRAME
F. TIRES
G. ROD FOR TONGUE ADJUSTMENT
H. TONGUE
I. 1-7/8” BALL HITCH
TECHNICAL DATA
S-ATV-180
Hopper Capacity
(liters/gallons)
LoadingHeight
(meters/inches)
Weight of the Unit
(kgs/lbs)
Width (wheel-wheel, outside)
(meters/inches)
Length
(meters/inches)
Hopper Width
(meters/inches)
Ball Hitch Diameter
(cms/inches)
Tires
(type/bar)
Spreading Width
(meters/feet)
Ground Cover Per hour
165 / 43,6
1,30 / 51”
80 / 175
1,05 / 41”
1,50 / 59”
0,90 / 35”
4,7625 / 1-7/8”
6,5 / 3,2
8 - 12 / 26’ - 40’
from 27 to 55 ha/h
from 7 to 15 acres/h
9
SIGNAL WORDS:
ThesignalwordsDANGER, WARNING and CAUTION areused withthe
safety messages in this manual and with each safety signs. They are
defined as follows:
DANGER: Indicates an immediate hazardous situation that, if not
avoided, could result in serious injury or death. This signal word is to be
limited to the most extreme situations typically for machine components
that, for functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not
avoided, could result in serious injury or death, and includes hazards
that are exposed when guards are removed. It may also be used to alert
against unsafe practices.
CAUTION: Indicatesapotentiallyhazardoussituationthat,if not avoided,
may result in minor or moderate injury. It may also be used to alert
against unsafe practice.
If you have any questions not answered in this manual or require additional
copies or the manual is damaged, please contact your dealer or King Kutter,
Inc. P.O. Box 1200 Winfield, AL 35594 (205) 487-3202 or www.kingkutter.com
READ AND FOLLOW THE INSTRUC-
TIONS IN THIS MANUAL AND ESPE-
CIALLY IN THE SAFETY SECTION.
FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY OR DEATH.
TAKE NOTE! THIS SAFETY ALERT
SYMBOL FOUND THROUGHOUT
THIS MANUAL IS USED TO CALL
YOUR ATTENTION TO INSTRUC-
TIONS INVOLVING YOUR PERSONAL
SAFETY AND THE SAFETY OF OTH-
ERS.
SAFETY
THISSYMBOLMEANS
ATTENTION!
BECOMEALERT!
YOUR SAFTEY IS INVOLVED
10
EQUIPMENT SAFETY GUIDELINES
zSafety of the operator and by standards is one of the main concerns in designing and
developing a spreader. However, every year accidents occur which could have been
avoided by a few seconds of thought and a more careful approach to handling equip-
ment. You, the operator, can avoid many accidents by observing the following precau-
tions and insist those working with you, or for you, follow them.
zIn order to provide a better view, certain photographs or illustrations in this manual may
show an assembly with a safety shield removed. However, equipment should never be
operated in this condition. Keep all shields in place. If shield removal becomes neces-
sary for repairs, replace the shield prior to use.
zReplace any safety sign that is not readable or is missing. Copies of such safety signs is
shown in this manual.
zNever use alcoholic beverages or drugs that can hinder alertness or coordination while
operating this equipment. Consult your doctor about operating this machine while taking
prescription medications.
zz
zz
zUnder no circumstances should children under the age of 18 be allowed to work
with this equipment. Do not allow persons to operate or assemble this unit until
they have read this manual and have developed a thorough understanding of
the safety precautions and of how it works. Review the safety instructions with all
usersannually.
zThis equipment is dangerous to children and persons unfamiliar with its operation. The
operator should be a responsible, properly trained and physically able person familiar
with farm machinery and trained in this equipment’s operations. If the elderly are assist-
ing with farm work, their physical limitations need to be recognized and accommodated.
zUse a tractor equipped with a Roll Over Protective System and seat belts. (ROPS)
zNever exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely,
is in question- DON’T TRY IT.
zDo not modify the equipment in any way. Unauthorized modification could result in seri-
ous injury or death and may impair the function and life of the equipment.
zIn addition to the design and the confirmation of this implement, including safety signs
and safety equipment, hazard control and accident prevention are dependent upon the
awareness, concern, prudence, and proper training of personnel involved in the opera-
tion, transport, maintenance, and storage of the machine. Refer also to safety messages
and operation instruction in each of the appropriate sections of the tractor and seeder/
spreader manuals. Pay close attention to the safety signs affixed to the tractor and the
seeder.
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Spargitore popolari di altre marche
Fisher
Fisher POLY-CASTER 78601 Manuale utente
TurfEx
TurfEx RS7200 Manuale del proprietario
Ferris
Ferris Pathfinder Series Manuale utente
Fayat Group
Fayat Group DYNAPAC S100 Guida alla risoluzione dei problemi
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manuale di installazione e funzionamento
EASTMAN
EASTMAN CR 500 Manuale utente
