Kinpo A200A Manuale utente
Kinpo Electronics, Inc.
Apollo 2 ADSL Network Modem
Model No.: A200A(A2)
Installation Manual
Version : E1
Date : Oct. 22, 1999
Software: Itex
1
CONTENTS
ABOUT THIS GUIDE
1. INTRODUCTION....................................................................................................................................2
2. INSTALLING THE ADSL NETWORK MODEM BOARD...............................................................5
3. INSTALLING THE APOLLO 2 DEVICE DRIVERS AND DIAGNOSTIC (ITEX ADSL A2
TEST APPLICATION)..........................................................................................................................6
3.1 WINDOWS 98........................................................................................................................................6
3.2 INSTALLING THE APOLLO 2 MODEM ICON UTILITY............................................................10
4. VERIFYING THE DRIVER INSTALLATION.................................................................................10
5. CONFIGURING THE ADSL NETWORK FOR RFC1483...............................................................11
6. CONFIGURING THE ADSL NETWORK FOR RFC1577...............................................................15
7. CONFIGURING THE ADSL NETWORK FOR PPP OVER ATM.................................................19
7.1 SETTING UP PPP OVER ATM........................................................................................................19
7.2 ESTABLISHING A PPP OVER ATM CONNECTION...................................................................19
8. ACTIVATING THE APOLLO 2 ADSL NETWORK MODEM.......................................................20
9. MONITORING THE APOLLO 2 ADSL NETWORK MODEM.....................................................20
10. UNINSTALLING THE APOLLO 2 ADSL NETWORK MODEM AND TEST APPLICATION20
11. SPECIFICATIONS...............................................................................................................................21
Preliminary
2
1. INTRODUCTION
ADSL Network
This is a diagram showing how an ADSL network looks.
Teleco
Public switch
Telephone
Telephone
The Internet
PC
Laptop computer
Fax
Telephone
SOHO
SOHO
Simutanious Voice, Video, Data and Image
Simutanious Voice, Video, Data and Image
3
System Requirement
The following equipment and information is required (at a minimum) to
setup your ADSL network modem.
[PC system requirement]
1. IBM PC and it’s compatibles with Pentium 100MHz CPU speed
2. 32Mbyte main memory and 10 Mbytes hard disk space
3. Microsoft Windows 98 (installation CD ready)
[ADSL network]
1. Subscribe to an ADSL service from your local telephone company or
have access to an ADSL DSLAM.
2. An IP address, gateway and DNS numbers from your telephone
company (for ADSL network configuration) or network administrator.
3. A VCI and VPI values from your telephone company (for ADSL network
configuration) or network administrator.
4
Before you start:
(Step 1) Insert
ADSL Network
Modem Card
(NMC)
(Step 2) Connect
NMC to ADSL
Network
(Step 3) Installing
Device Driver and
Diagnostic
Program
(Step 5)
Verifying the
Device Driver
Installation
Yes
(Step 4) Reboot
(Step 6)
Configuring the
ADSL Network
(1)TCP/IP
(2) Gateway
(3) DNS
(Step 7) Reboot
ITeX ADSL Network Modem
Installation and Configuration Flow Chart
Troubleshooting
(TBS xx.xx) No
Step 8
Activating the
Apollo 2 ADSL
Network Modem
(Step 9)
Monitoring the
Apollo 2 ADSL
Network Modem
End
5
2. INSTALLING THE ADSL NETWORK MODEM BOARD
Before installing the ITeX ADSL Network Modem board, please make sure that
the following minimum system requirements are met.
Minimum System Requirement
[PC System Requirement]
1. IBM PC and its compatibles with Pentium 100MHz CPU speed
2. 32MB main memory and 10MB hard disk space
3. Microsoft Windows 98 (Installation CD)
[ADSL Network Subscription]
1. Subscribe to an ADSL service from your local telephone company or service
provider or have access to an ADSL DSLAM.
2. An IP address, gateway and DNS numbers from the telephone company (for
ADSL network configuration) or from your network administrator.
3. A VCI and VPI value from your telephone company (for ADSL network
configuration) or network administrator.
Before installing the ITeX ADSL Network Modem, please make sure that the
power to the computer is turned off. Remove the cover of the personal computer.
Insert the ITeX ADSL Network Modem into one of the free PCI slots available.
Consult your computer's manual for instructions on where to find the PCI slot.
Make sure that the network modem is securely fastened into the computer.
Connect the ADSL phone line directly to the RJ-11 connector marked "L". If
there is no marking, then connect the ADSL phone line to the top connector of
the modem. Also, since the ITeX ADSL Network Modem comes equipped with
an inline filter, you can attach a phone directly to the second RJ-11 jack.
6
3. INSTALLING THE APOLLO 2 DEVICE DRIVERS AND DIAGNOSTIC (ITeX
ADSL A2 Test Application)
Please have the following information available in order to complete the
installation and setup of the ITeX Apollo 2 ADSL Network Modem.
1. TCP/IP properties, this includes the PVC values (VPI and VCI), IP address,
the gateway, and the domain name server. You will need this information to
complete the configuration of the network modem card. Please contact your
MIS manager for more information regarding the TCP/IP settings.
2. Windows 98 CD.
3.1 Windows 98
This installation guide will walk the user through the installation of the ITeX Apollo
2 ADSL Network Modem software drivers and help to configure the modem.
Windows will find the ITeX ADSL Network Modem and will search for a device
driver for the card. Click Next.
7
The Add New Hardware Wizard window will appear. When prompted, select
"search for the best driver for your device. (Recommended). Click "Next".
Insert the Apollo 2 ADSL Software Drivers CD into your CD-ROM drive and
select the "Specify a location" option from the menu and type “Drive:\win95_98 or
win98sec_2000 or nt4” (where drive is your CD-ROM drive). Click "Next".
8
Windows should find the NETITEX.INF file in the floppy disk drive. Click "Next"
to continue.
Windows will start to copy the drivers. Make sure that the Windows 98 CD is in
the CD-ROM or that it is easily accessible.
9
For RFC1483, the default PVC values are 8 and 35 for VPI and VCI respectively.
If necessary, these values can be changed at this time.
Windows has finished installing all the ITeX ADSL Network Modem drivers. Click
"Finish" to complete the installation.
Altri manuali per A200A
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Kinpo Modem
