Klearbar Mini Manuale di istruzioni

KLEARBAR hot/cold countertop filter water dispenser

INSTALLATION/USER MANUAL

Overview & Diagram

----------------------------------------------------------------------------------------------

Touch screen instructions/user guide

1. Touchscreen operation panel

2. Front panel indicator light:

Blue - COLD water

Red - HOT water

Purple - ENERGY SAVE mode (Energy

save mode will start after 4 hours of

non-use. Touch any key to bring

system to normal operation

condition)

3. Faucet

4. Removable drip tray

1. Tank refill activation icon

2. Hot water activation icon

3. UV light activation icon (Mini2 only)

4. Cold water activation icon

For HOT water dispense touch and release #5,

then touch and hold #6

For COLD water dispense touch and hold #7

5. Removable top panel

6. On/Off cold water compressor and

delivery pump

7. On/Off hot water tank

8. Water overflow line outlet

9. Water line inlet (inset included 1/4

stem elbow here)

Installation & Maintenance

Your Klearbar Mini comes standard with virtually everything you need for a simple water line

connection:

Installation/User manual

15 feet of food grade, 1/4 polyethylene tubing

45 psi pressure reducer (pre-installed inside water dispenser)

Angle stop valve (mains connector)

1/4 union tee (install if using existing ice maker water line connection)

1/4 stem elbow (install at water line inlet)

You may also need the following items to assist your installation:

Adjustable wrench to install angle stop valve

Teflon plumbers tape (use when installing angle stop valve)

Plastic tubing cutter or scissors

3/8 inch drill bit and drill (if needed to drill hole in cabinetry to hide water line)

ALWAYS PLUG KLEARBAR MINI ELECTRICAL CORD INTO A GFCI PROTECTED POWER OUTLET

There are multiple ways to connect your Klearbar Mini but regardless of your choice it is recommended

to follow local plumbing codes or consider hiring a licensed plumber. But should you decide to DIY (do it

yourself) we have provided a basic blueprint to get you on your way.

Perhaps the easiest connection is to an existing water line already provided by your refrigerator ice

maker. Use a 1/4 union tee for this connection.

Connect To Existing Refrigerator Ice Maker Water Line—use the included 1/4 union tee when

connecting to a 1/4 water mains connection or, use a brass compression union tee if desired (always use

a plastic compression ferrule when connecting polyethylene tubing using a brass union—a brass

compression ferrule may cut into the plastic tubing and cause a leak).

1. BEFORE PLUGGING IN TO ELECTRICITY turn off water line supply to refrigerator ice maker.

2. Using a plastic tube or copper line cutter, make a square cut of the existing ice maker water line

no closer than 12 inches from where the water line originates from the floor or wall, and insert

the 1/4 union tee here. It may be good to have a large towel nearby as a small amount of

residual water may spray and drain out once the line is cut. Connect the included 1/4

polyethylene water line (tubing) to the union tee.

3. Place the Klearbar Mini within a few feet of an available GFCI electrical socket and connect the

included 1/4 stem elbow into the water inlet port on the back of the unit (be careful not to

connect to the optional overflow port). Now connect the remaining 1/4 polyethylene water line

into the 1/4 elbow behind the Klearbar Mini. Trim off extra water line as needed for a

professional look.

4. Consider installing an optional 1/4 turn ball valve (not included; available at most hardware

stores) about 12 inches from the 1/4 stem elbow enabling easy water on/off access without

having to pull the refrigerator away from the wall. This is very convenient should you ever need

to remove the Klearbar Mini for cleaning or should you discover a leak.

5. Position the Klearbar no closer than three inches from the wall to allow sufficient air flow.

6. BEFORE TURNING ON WATER LIFT RESERVOIR COVER THEN

FROM INSIDE RESERVOIR.

7. BEFORE TURNING ON WATER PLACE HOT WATER SWITCH TO OFF POSITION and then plug the

Klearbar Mini into a GFCI receptacle. Open the water connection and allow to completely fill.

Once full prime the water pump by dispensing 10 ounces of water from the cold and hot tanks.

Only after priming is it now safe to turn on the cold and hot water switches on the rear of the

equipment.

Connect To Main beneath a Sink

1. Turn off COLD water supply line.

2. Use a wrench and disconnect the copper or braided riser tube generally connected to a 3/8

vertical thread as part of an on/off valve threaded or soldered to the water main.

3. Thread the included angle stop valve (mains connector) by first wrapping Teflon tape (not

included) around the vertical mains thread. Hand-tighten then snugly tighten using wrench.

Then apply Teflon tape to downstream thread and reconnect the riser tube.

4. Use the included 1/4 polyethylene tubing and connect using the compression fittings on the

included mains connector.

5. Next drill a 3/8 hole through sink or countertop near the final resting place of the Klearbar Mini.

Be extremely careful if drilling through a porcelain/cast iron sink or granite countertop as

damage may result. Consult a professional if unsure with this procedure.

6. Place the Klearbar Mini within a few feet of an available GFCI electrical socket and connect the

included 1/4 stem elbow into the water inlet port on the back of the unit (be careful not to

connect to the optional overflow port). Now pull the 1/4 water line through the drilled hole and

connect into the 1/4 stem elbow.

7. Install an optional 1/4 turn ball valve (not included; available at most hardware stores) about 12

inches from the 1/4 stem elbow enabling easy on/off access. This is very convenient should you

ever need to remove the Klearbar Mini for cleaning or should you discover a leak.

8. Turn on mains valve, check for leaks then plug the Klearbar Mini into a GFCI receptacle allowing

to completely fill. Once full the Klearbar Mini will automatically stop filling with water. MAKE

SURE THE HOT WATER SWITCH IS IN THE OFF POSITION BEFORE PLUGGING IN. Once the

Klearbar Mini has filled and water is no longer flowing in, it is now safe to turn on the hot and

cold water tanks.

Optional tee adaptor connection

User Maintenance

It is recommended to flush and sanitize your Klearbar Mini upon installation and after a filter change

approximately every six months or as needed to assure the freshest drinking water possible.

Use a 5-quart, pre-mixed solution of hot tap water and sanitizer (baking soda or citric acid). If using

bleach avoid prolonged periods of use to minimize stress on stainless water tank and optional UV

component. Flush with clean tap water thoroughly after a one hour soak.

New Installation

1. Remove all packing materials before performing procedures below.

2. Make sure both hot and cold switches are in the off position.

3. Pre-mix 5 quarts o very hot or near boiling tap water to the following

a. OPTIONAL Sodium bicarbonate (baking soda) –8 tablespoons (4 oz.)

WARNING: IF USING BLEACH BE MINDFUL OF POTENTIAL STAINING OF CLOTHES IF SPILLED

WARNING: IF USING OPTIONAL SANITIZER WITH KLEARBAR MINI2 ONLY, DISCONNECT UV LAMP

COMPONENT BEFORE ADDING SOLUTION TO PREVENT POTENTIAL OF BAD AFTERTASTE. KLEARBAR

MINI2 WILL NOT LEAK WHEN REMOVING THE UV LAMP. AVOID TOUCHING UV LAMP WITH BARE

FINGERS TO PREVENT NATURAL OIL TRANSFER ONTO LAMP WHICH MAY DECREASE LAMP LIFE.

REINSERT UV LAMP WHEN FLUSHING IS COMPLETE.

4. Plug Mini into GFCI electrical outlet

5. Remove top reservoir cover and slowly pour sanitizing solution into top of empty reservoir

6. Dispense from both hot and cold water sides to fill internal lines with solution

7. Soak for 1-3 hours, dispense ALL water from both sides to flush, fill again with clean tap water,

dispense from both sides to rinse

8. If poor odor/taste exists with new installation, dispense 1-2 full pitchers of cold water. It may be

necessary to repeat 12, 24 and 48 hours after installation. Repeat as needed.

NOTE: ANOTHER DRAINING METHOD IS TO REMOVE SILICON PLUGS FROM BOTTOM OF KLEARBAR

MINI. REMEMBER TO REPLACE BEFORE REFILING.

Between Filter Changes

1. Turn off water supply to the Klearbar Mini

2. Turn off both hot and cold switches

3. Pre-mix 5 quarts o very hot or near boiling tap water to the following

a. OPTIONAL Sodium bicarbonate (baking soda) –8 tablespoons (4 oz.)

WARNING: IF USING BLEACH BE MINDFUL OF POTENTIAL STAINING OF CLOTHES IF SPILLED

WARNING: IF USING OPTIONAL SANITIZER WITH KLEARBAR MINI2 ONLY, DISCONNECT UV LAMP

COMPONENT BEFORE ADDING SOLUTION TO PREVENT POTENTIAL OF BAD AFTERTASTE. KLEARBAR

MINI2 WILL NOT LEAK WHEN REMOVING THE UV LAMP. AVOID TOUCHING UV LAMP WITH BARE

FINGERS TO PREVENT NATURAL OIL TRANSFER ONTO LAMP WHICH MAY DECREASE LAMP LIFE.

REINSERT UV LAMP WHEN FLUSHING IS COMPLETE.

4. Fully drain both hot and cold sides of reservoir

5. Remove top reservoir cover and slowly pour sanitizing solution into top of empty reservoir. Hot

tank will fill before upper part of cold tank reservoir.

6. Dispense from both hot and cold water sides to fill internal lines with solution

7. Soak for 1-3 hours, dispense ALL water from both sides to flush, fill again with clean tap water,

dispense from both sides to rinse

Changing the Water Filter

1. Lift top black cover back to front to remove. Turn off water supply then turn filter in a half turn

counterclockwise and pull up. Insert new filter and turn clockwise to fully engage back into unit.

2. Turn water supply back on and dispense at least three (3) gallons of cold water. This procedure

will drain old water and flush new filter. If you see unflushed carbon fines these may appear as

black specks in the water and are not harmful, but may not present well so consider additional

flushing after inserting the new filter. It is also suggested to sanitize both the hot and cold tanks

similar to the new install procedure every other filter change (12 months) as needed.

Replacement filter part # 37MC235

Cleaning Your Klearbar Mini

Using a microfiber or soft cloth dampened with warm water you can wipe your Klearbar Mini’s outer

panels. Do not use harsh detergents or other cleaning aids which can possibly damage the outer

surface. Use only a dry cloth to wipe the touch screen. Do not use water or any other detergent to

clean the back of the machine. Keep dry!

Changing Color Panels

Your Klearbar Mini color side panels are easily changeable with a Phillips head screwdriver.

Remove the top black cover

Locate the two screws on both the front and back top corners of each side panel

Loosen both screws for each panel

Facing either panel, position your thumbs half way down near the edge of both sides (left thumb

on the left side and right thumb on the right side)

Press and slide in a downward motion which should unlatch the panel from the inside allowing

you to remove. Do this for both sides. Install the new panels in reverse and you’re done!

Replacement Color Panels (2 per set)

Red, part # MINIP-RED

Black, part # MINIP-BLK

Silver, part # MINIP-SLV

Cream, part # MINIP-CRM

Blue, part # MINIP-BLU

Green, part # MINIP-GRN

Yellow, part # MINIP-YEL

Orange, part # MINIP-ORG

Safety Instructions

Do not use extension cords or power adaptors to avoid overheating and potential fire hazards.

Only connect the Klearbar Mini to a GFCI grounded power source.

Do not use if there is a defect in either the electrical cable, power source or any other part of

the Klearbar Mini. Call you vendor for assistance on any questions related to these issues.

Do not let children operate the Klearbar Mini unattended by an adult.

The Klearbar Mini can dispense extremely hot water which can cause severe burns if handled

inappropriately.

To avoid water damage and overflowing do not reposition the Klearbar Mini prior to first

shutting off the water inlet and then emptying both internal hot and cold water tanks.

The Klearbar Mini is intended to purifying and filtering drinking water as provided by NSF

standards.

In case there is an official recommendation by the public health authority to boil water prior to

drinking tap water in your area, do not use the Klearbar Mini. The Klearbar Mini is intended for

use with approved potable water only. Replace the filter, sanitize and thoroughly flush the

Klearbar Mini immediately after boil water advisory has lifted.

Leave a minimum two inch space on all sides of the Klearbar Mini for proper venting and

operation of the cooling and heating systems.

If you do not intend to use your Klearbar Mini for several days, for safety purposes, unplug it

and close the incoming water supply line into the machine. When the machine is turned back

on, it is recommended to flush and sanitize both tanks as described above.

Klearbar, Inc. will not be responsible for any internal changes to the Klearbar Mini made by an

unauthorized installer, as well as for any defect, malfunction or damage caused by the use of

non-original replacement parts.

Servicing and repairs should solely be handled by an authorized dealer and any warranty is

limited to original parts from Klearbar or an authorized dealer.

Technical Specifications

Electricity

120v, 60Hz

115 –700w

7.5 Amps

Heating System

53 ounce/1.6 liter capacity dispenses up to 40 cups of hot water an hour (2.2 gallons/8.2 liters)

at an average temperature of 185 F/85 C.

Cooling System

73 ounce/2.2 liter capacity dispenses up to 40 cups of cold water an hour (2.0 gallons/7.6 liters)

at an average temperature of 50 F/10 C.

R134 refrigerant, 1.5873 oz.

32 ounce/1.0 liter ambient water capacity above cold water baffle; 105 ounce/3.1 liter total

main tank capacity

Purification and Filtration Systems

300 gallon, 1 micron carbon block filter

oKlearbar Smart filter part # 37MC235

oNSF 42

oReplace a minimum of every six months

Water Supply

Minimum water pressure 22 psi

Maximum water pressure 87 psi

Product Dimensions

14.75 H x 12.63 W x 15.75 D

29.2 lbs. net weight

Altri manuali per Mini

Indice

Altri manuali Klearbar Distributore d'acqua

Klearbar

Klearbar Mini Manuale di istruzioni

Manuali Distributore d'acqua popolari di altre marche

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE Manuale utente

Haier

Haier HLM-109B Manuale utente

abc

abc Fleck 5600SXT Manuale utente

GE GXOF18G Istruzioni operative

Kenmore

Kenmore 625.385560 UltraFilter 650 Manuale utente

Innova

Innova CEV+ Guida rapida

Aries

Aries Hydra DI Manuale

GE GNCF02H Manuale utente

ProFlo

ProFlo PFB Series Manuale utente

Hydrotech

Hydrotech 89DF HIM Manuale utente

A.O. Smith

A.O. Smith FREZYA 300S Manuale utente

Frakco

Frakco Travelsoft RV 2400HD Manuale utente

GE GXSF30V Istruzioni operative

Avanti

Avanti WD31EC Manuale utente

Avanti

Avanti WD360 Manuale utente

BRIO

BRIO CLCTTL520 Guida utente

3M HCD-1 Manuale utente

Elkay

Elkay EFHFA8_2CJO Manuale di installazione