Klipsch ON-EAR Manuale utente
ON-EAR
BLUETOOTH
® OWNER’S MANUAL
INSIDE
CONTENU
CONTENIDO
INHALT
CONTENUTO
CONTEÚDO
目录
IMPORTANT SAFETY INFORMATION
1.
READ these instructions.
2.
KEEP these instructions.
3.
HEED all warnings.
4.
FOLLOW all these instructions.
5.
DO NOT use this apparatus near water
or moisture.
6.
If you hear ringing or experience pain
or discomfort in your ears during or
after using any in-ear audio product,
that is a sign you are listening too
loud.
When your ears are exposed to high
volumes (in excess of 85dB) for over
an hour, you may be permanently
damaging your hearing.
7.
Turn down your listening device’s
volume to zero before you insert the
Klipsch headphones and turn on the
device. Once you have the headphones
on, gradually increase the volume to a
comfortable, moderate volume.
8.
Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9. ONLY USE attachments/accessories
specified by the manufacturer.
10.
REFER all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in
any way, such as power-supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
11.
NEVER operate a motor vehicle
while listening to or wearing your
headphones. Not only dangerous,
it is illegal in many places.
12.
NEVER operate heavy machinery
while listening to or wearing your
headphones.
13.
We don’t recommend you use the
headphones while riding a bicycle,
running,or walking in heavy traffic
areas.
WARNING:
Except in case of emergency, Klipsch
recommends you do not use these
headphones or headsets (headphones plus
microphone) as aviation communication
equipment as they are not engineered
for many environmental conditions
common in commercial or non-commercial
aircraft (including, but not limited to:
altitude, temperature, noise conditions,
unpressurized aircraft, etc.) resulting
in possible interference to critical
communications.
The Occupational Safety Health
Administration (OSHA) has issued
headphone usage recommendations
for maximum daily exposure and sound
pressure levels (measured in decibels (dB)).
A decibel is a unit of measure of sound, and
decibels increase exponentially as sound
gets louder. For example, conversational
speech is typically around 60dB, and a rock
concert in a stadium is often about 110dB.
OSHA GUIDELINES FOR NOISE EXPOSURE
LIMITS
Sound
Pressure
Level
Recommended
Maximum Exposure
Per Day
90dB 8 Hours
92dB 6 Hours
95dB 4 Hours
97dB 3 Hours
100dB 2 Hours
102dB 1.5 Hours
105dB 1 Hours
110dB 30 Minutes
115dB 15 Minutes or less
120dB Avoid as damage may
occur
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms
to European Union Low Voltage Directive
2006/95/EC; European Union EMC Directive
2004/108/EC; European Union RoHS
Directive 2002/95/EC; European Union WEEE
Directive 2002/96/EC; European Union
Registration, Evaluation, Authorization and
Restriction of Chemicals (REACH) Directive
2006/121/EC.
WEEE NOTICE
Note: This mark applies only to
countries within the European
Union (EU) and Norway.
This appliance is labeled in
accordance with European Directive
2002/96/EC concerning waste electrical
and electronic equipment (WEEE). This label
indicates that this product should not be
disposed of with household waste. It should
be deposited at an appropriate facility to
enable recovery and recycling.
FCC AND CANADA EMC COMPLIANCE
INFORMATION
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not in-stalled and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Approved under the verification provision of FCC
Part 15 as a Class B Digital Device.
Caution: Changes or modifications not expressly
approved by the manufacturer could void the
user’s authority to operate this device.
Caution: To comply with the limits of the Class
B digital device, pursuant to Part 15 of the FCC
rules, this device is to comply with Class B limits.
all peripherals must be shielded and grounded.
Operation with non-certified peripherals or
non-shielded cables my result in interference to
radio or reception.
This Class B digital apparatus complies with
Canadian ICES-003.
WIRELESS TRANSMITTER COMPLIANCE
INFORMATION
The term “IC:” before the radio certification
number only signifies that Industry Canada
technical specifications were met.
This device complies with part 15 of the FCC
rules and the applicable Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
PRODUCT REGISTRATION
Register your product online at www.klipsch.
com/register
• Klipsch will keep you up-to-date on new
products and promotions.
• Your personal information will never be
resold.
• This registration information is not used
for warranty purposes. Please retain your
receipt for warranty claims.
POWER/PAIR
CHARGING
JACK
HEADPHONE
JACK
STATUS
INDICATOR
HOLD
2 SECONDS
HOLD
2 SECONDS
GETTING STARTED
1. Turn on the headset by pressing the Power/Pair button for 2 sec-
onds. The headset will automatically go to pairing mode and the
status indicator will begin pulsing BLUE.
2. Connect to “Klipsch On-Ear BT” from your device.
3. Once connected, the headset will periodically blink BLUE.
Note: The headset will automatically pair to the last device connected to it
when turned on.
TURNING OFF
Press the Power/Pair button for 5 seconds to turn the headset off.
CHARGING
Use the included Micro-USB cable to charge the headset from your
computer or USB wall adapter (not included). The status indicator will
glow RED until the headset is charged, at which point it will turn off.
Altri manuali per ON-EAR
3
Indice
Lingue:
Altri manuali Klipsch Auricolare Bluetooth
