KM SVS2000 Manuale utente
SVS2000
Installation & Operation Manual
IOM
97-1129-01 Rev. D
SVS2000
Installation & Operation Manual
CONTENTS
I. HANDLING AND STORAGE..................................................................................................................... 1
Save These Instructions
Inspection And Handling
Disposal And Recycling
Storage
II. GENERAL SAFETY................................................................................................................................... 2
Authorized Personnel
Use
Misuse
III. PRODUCT DESCRIPTION ....................................................................................................................... 3
Function
IV. MECHANICAL INSTALLATION................................................................................................................. 5
Mounting
V. ELECTRICAL INSTALLATION ................................................................................................................ 11
General Safety
Disconnect Requirements For Permanently Installed Equipment
Installation
Figure 1. Wiring Diagram
Figure 2. Wiring Diagram
Figure 3. Wiring Diagram Current Output Card
Figure 4. Wiring Diagram Isolated Output Card
VI. SET-UP ............................................................................................................................................. 18
Figure 6. Preparing Supplied Plug for Unused Openings
Table 3. Interaction of Format and Countby
Figure 7. High Accuracy Calibration
Figure 8. Calculation by Subtracting a Known Quantity
Figure 9. Manual Calibration
Table 4. Calibration Display
Figure 11. Set Point
Table 5. Available gain settings and corresponding sensor input voltages.
Figure 12. Sensor Display
Figure 13. DSP Filter Parameters
Figure 14. Material and Zero Tracking
Table 6. Microcell Sensitivity Factors
SAFETY SYMBOLS
WARNING:
IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT FOLLOWED, COULD
RESULT IN SERIOUS INJURY. RISK OF ELECTRICAL SHOCK.
CAUTION:
IDENTIFIES CONDITIONS OR PROCEDURES, WHICH IF NOT FOLLOWED, COULD
RESULT IN SERIOUS DAMAGE OR FAILURE OF THE EQUIPMENT.
VIII. TROUBLESHOOTING............................................................................................................................ 75
Hot Keys
SVS Display Tree
Setup Table
Parameter Default
1
www.kistlermorse.com
97-1129-01 Rev. D
SVS2000
Installation & Operation Manual
I. HANDLING AND STORAGE
SAVE THESE INSTRUCTIONS
INSPECTION AND HANDLING
Do not dispose of the carton or packing materials.
Each package should be inspected upon receipt for damage that may have occurred due to mishandling during
shipping. If the unit is received damaged, notify the carrier or the factory for instructions. Failure to do so may
void your warranty. If you have any problems or questions, consult Customer Support at 800-xxx-xxxx.
DISPOSAL AND RECYCLING
This product can be recycled by specialized companies and must not be disposed of in a municipal collection
site. If you do not have the means to dispose of properly, please contact for return and disposal instructions or
options.
STORAGE
If the device is not scheduled for immediate installation following delivery, the following steps should be
1. Following inspection, repackage the unit into its original packaging.
2. Select a clean dry site, free of vibration, shock and impact hazards.
3. If storage will be extended longer than 30 days, the unit must be stored at temperatures between
32º and 104º F (0º to 40° C) in non-condensing atmosphere with humidity less than 85%.
CAUTION: DO NOT STORE A NON-POWERED UNIT OUTDOORS FOR A PROLONGED PERIOD.
297-1129-01 Rev. D
www.kistlermorse.com
II. GENERAL SAFETY
AUTHORIZED PERSONNEL
functions of the device. The required personal protective equipment must always be worn when servicing this
device.
USE
The device is solely intended for use as described in this manual. Reliable operation is ensured only if the
should be mounted in locations where it will not be subject to tampering by unauthorized personnel.
MISUSE
If any questions or problems arise during installation of this equipment, please contact Customer Support at
800-426-9010.
3
www.kistlermorse.com
97-1129-01 Rev. D
III. PRODUCT DESCRIPTION
FUNCTION
The SVS2000 accepts input signals from half- or full-bridge strain gage load cells through a high resolution (up
to 21-bit) analog-to-digital converter. Resolution and gain are adjustable for optimal system performance. Weight
is displayed at the indicator and the data can be serially polled from a master device. Analog and digital outputs
can be generated from the inputs to the SVS2000 to provide auxiliary controls.
QUICK CONFIGURATION
Adjusts system parameters and precalibrates unit without special load cells.
SENTRYTM
Separates mixer and plant vibrations from weight changes. This provides accurate and reliable weight readings.
Performance for demanding applications with up to 21-bit resolution.
Simple, understandable operator messages eliminates special coding/decoding, cryptic setup and
diagnostic messages.
Displays the weight as a bar graph or digital readout.
497-1129-01 Rev. D
www.kistlermorse.com
TECHNICAL SPECIFICATIONS
FUNCTIONAL
Voltage - Operating Range
Operating Temperature -4º to 122º F (-20º to 50º C)
PERFORMANCE
Transducer/Sensor Input All Kistler-Morse half-bridge sensors, full-bridge foil gage
Excitation Programmable between 5 and 13 volts @ 400 mA
Resolution
Selectable 16 bits (1 part in 65,536) to 21 bits (1 part in 2,097,152) in 1 bit increments
Conversion Speed 16 bits = 17 ms, 17 bits = 20 ms, 18 bits = 25 ms, 19 bits = 34 ms,
20 bits = 50 ms, 21 bits = 100 ms
Span
excitation, Gain = 128
Temperature Stability
Common Mode
Rejection
Normal Mode Rejection 100 db min @ 60 Hz
Multi-Vessel Remote Tare
Relay Output
for motors and other large inductive loads, contractors rated for the load are required.
PHYSICAL
Display
or engineering units format
Programming/Parameter
Entry Integral 19-key sealed membrane tactile keypad
Setup Menu-driven prompts
Memory Non-volatile RAM
Enclosure
Humidity 1% to 95% (non-condensing)
Storage -4º to 140º F (-20º to 60º C)
Dimensions
Mounting Hole Pattern
Shipping Weight
OPTIONS
load 600 ohms with internal loop supply
APPROVALS
5
www.kistlermorse.com
97-1129-01 Rev. D
IV. MECHANICAL INSTALLATION
WARNING: REMOVE POWER FROM THE UNIT BEFORE INSTALLING, REMOVING, OR MAKING
ADJUSTMENTS.
MOUNTING
The hardware used to mount the SVS2000 is provided by the customer. (Including suggested torque wrench
CAUTION: ONLY USE SIKAFLEX 1A POLYURETHANE SEALANT OR DOW CORNING RTV 739 OR
RTV 738. OTHER SEALANTS MAY CONTAIN ACETIC ACID, WHICH IS HARMFUL TO SENSORS
AND ELECTRONICS.
removed together.
2. Hold the SVS2000 in the desired location and mark the positions of the mounting holes.
3. Drill the mounting holes.
5. (SS version) Make entry holes in the bottom of the enclosure for cables and conduit. Hole location is
6. (SS version) Re-install baseplate with electronics.
697-1129-01 Rev. D
www.kistlermorse.com
Indice
