Knightsbridge KIT4B Manuale di istruzioni

INSTALLATION & MAINTENANCE MANUAL

KIT4B / KIT4W

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following products:

KIT4B / KIT4W

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

• Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is ﬁtted) does not exceed

the rating of the circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• This product is intended to be installed into decking or similar

• This product is Class II

• This product is IP44 rated

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please

conﬁrm with the manufacturer of the sensors that they are compatible with LED luminaires.

• A suitable 230V 50Hz IP rated socket outlet is required at the point of installation (refer

to BS7671 for correct cabling methods). Suitable IP rated junction boxes should be used

where required

• The power source connections should be local and accessible

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring

not to infringe with any joists, gas/water pipes or electrical cables

Fig. 1

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

KIT4B / KIT4W

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of

the circuit cable, fuse, or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•This product is intended to be installed into decking or similar

•This product is Class II

•This product is IP44 rated

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires.

•A suitable 230V 50Hz IP rated socket outlet is required at the point of installation (refer to BS7671 for

correct cabling methods). Suitable IP rated junction boxes should be used where required

•The power source connections should be local and accessible

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas/water pipes or electrical cables

38mm

Fig. 1

•We recommend not installing in areas where there is a high risk of flooding or areas where water may

sit on top of the fitting

•Feed the cable of each fitting through the holes and connect the pre-installed plugs into the splitter

box (see Fig. 2)

Fig. 2

• We recommend not installing in areas where there is a high risk of ﬂooding or areas

where water may sit on top of the ﬁtting

• Feed the cable of each ﬁtting through the holes and connect the pre-installed plugs into

the splitter box (see Fig. 2)

•A 45mm minimum void beneath the luminaire is recommended

•When installing into decking, ensure there is enough clearance beneath, and that the

cable and splitter box are not laying in water

•Secure the luminaires into the mounting surface

•Plug the 13A plug adaptor into a suitable socket outlet

•Switch on and check for correct operation

Fig. 2

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

KIT4B / KIT4W

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of

the circuit cable, fuse, or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•This product is intended to be installed into decking or similar

•This product is Class II

•This product is IP44 rated

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires.

•A suitable 230V 50Hz IP rated socket outlet is required at the point of installation (refer to BS7671 for

correct cabling methods). Suitable IP rated junction boxes should be used where required

•The power source connections should be local and accessible

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas/water pipes or electrical cables

38mm

Fig. 1

•We recommend not installing in areas where there is a high risk of flooding or areas where water may

sit on top of the fitting

•Feed the cable of each fitting through the holes and connect the pre-installed plugs into the splitter

box (see Fig. 2)

Fig. 2

GENERAL

WARNING

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm

water only, do not use aggressive cleaning products or solvents which may damage the

product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

A light ﬁlm of acid-free oil is recommended after installation and maintained periodically

(2-3 times a year) to aid corrosion prevention.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

This product must be disconnected from the circuit if subjected to any high voltage or

insulation resistance testing. Irreparable damage will occur to the lamp if this instruction is

not followed.

This product is not suitable for installation in or near a coastal or marine environment.

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

DOCT21_V4

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

35°C

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Knightsbridge Attrezzatura di illuminazione

Knightsbridge

Knightsbridge BATC Series Manuale di istruzioni

Knightsbridge

Knightsbridge LED Series Manuale di istruzioni

Knightsbridge

Knightsbridge EMSWING Manuale di istruzioni

Knightsbridge

Knightsbridge OS002 Manuale di istruzioni

Knightsbridge

Knightsbridge TRLED 1 Series Manuale di istruzioni

Knightsbridge

Knightsbridge SPIKEGUBK Manuale di istruzioni

Knightsbridge

Knightsbridge TNXQUADEMW Manuale di istruzioni

Knightsbridge

Knightsbridge 24DCIP60 Manuale di istruzioni

Knightsbridge

Knightsbridge 12DC36 Manuale di istruzioni

Knightsbridge

Knightsbridge HBN Series Manuale di istruzioni

Knightsbridge

Knightsbridge LEDFIPCCT Manuale di istruzioni

Knightsbridge

Knightsbridge SHE P Series Manuale di istruzioni

Knightsbridge

Knightsbridge LFX512WW Manuale di istruzioni

Knightsbridge

Knightsbridge KIT16 Manuale di istruzioni

Knightsbridge

Knightsbridge LWALL1A Manuale di istruzioni

Knightsbridge

Knightsbridge BLED5BW Manuale di istruzioni

Knightsbridge

Knightsbridge TNXQUADMWSTW Manuale di istruzioni

Knightsbridge

Knightsbridge HBLR Manuale di istruzioni

Knightsbridge

Knightsbridge RWL Series Manuale di istruzioni

Knightsbridge

Knightsbridge TNXQUADMWEMW Manuale di istruzioni

Knightsbridge

Knightsbridge BT9EMS Manuale di istruzioni

Knightsbridge

Knightsbridge OS009 Manuale di istruzioni

Knightsbridge

Knightsbridge LEDM06 Series Manuale di istruzioni

Knightsbridge

Knightsbridge TNXQUADSTW Manuale di istruzioni

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente