Koganei DTY-ELG21 Manuale utente

Catalog No.BK-P048

DTY-ELG21

□Features □Speciﬁ cation

●The product has a 200g light weight body, and designed

for easy holding. 

20% reduction in weight (compared to our products)

●A high-frequency AC method provides high efﬁ ciency of

electrostatic charge removal and outstanding ion

balance.

●Highly ﬂ exible robot cable is used for connection.

●A separate controller is unnecessary because a valve

and ion generator is built in.

●Pulsed air improves energy saving/dust removal

efﬁ ciency by installing a pulse blow unit (sold separately).

Model

Item DTY-ELG21

Input voltageV DC24 ± 5%

Consumption current mA Approx. 100

Output voltage kV Approx. 2.5 (high frequency type)

Display Power Power indicator LED (green)

Alarm Alarm indicator LED (red)

Outer dimensions mm

164.6（L）×25（W）×135.8（H）

(not including protrusions)

Massg200(without cables)

Ion balance *1 V ± 15

Ozone generation amount *2

ppm 0.04 or less

Medium *3 Air (clean air, water vapor and oil removed)

Operating air pressure range

MPa 0.05 〜 0.6

Operating Environment

Indoors: 0 to 40°C/65% or less (non-condensation)

Material Body: PBT, Nozzle: PPS

Accessories AC Adapter, Instruction Manual

*1:Distance 100mm from nozzle port, pressure 0. 6MPa

*2: Distance 200mm from the nozzle port, Pressure 0. 2MPa

*3: Be sure to supply air when using.

Remark 1: Ion balance is measured according to our measurement conditions.

2: Do not use other nozzles other than DTY-ZN1-G21.

Power indicator LED (green)

Alarm indicator LED (red)

Suspensionbracket

canbemanually

rotatedby90°.

Static Electricity Removing Unit Ionizer

Air gun type

●Main unit

DTY-ELG21

Ordercodes

AC adapter (accessory)

Rating

input : AC100〜240V

50/60Hz 0.58A

Output : DC24V 1A

Cable length: 300 mm

DTRY-ZEM-G11

NOTE : For ELG11/21 air gun type only

●Options(soldseparately)

Replacementtungstendischargeneedle(unit:5perset)

Special tool for replacing discharge needle

NOTE: Only bits are for sale.

AC Adapter (300mm)

Replacement nozzle

DTRY-ELB21

DTY-ZN1-G21

6.35 9

φ4.5

Shape of jig for replaceable bit

Main unit

Cable length :3000 mm

Replacement of discharge needle

When replacing the discharging needle, use the dedicated tool DTRY-ELB21 in combination with a torque driver.The dedicated tool is designed not

to damage the discharge needle or the threaded part of the main body. Replacing with another tool may cause damage to the discharge needle and

main body, etc.The tightening torque for replacement should be 15 to 20N·cm.If the discharge needle is replaced without using the dedicated tool

and the discharge needle, main body, etc. are damaged, the warranty will not cover.

NOTE: When replacing the nozzle or take off the nozzle for the maintenance of the discharge needle, tighten the nozzle securely by hand without

using a tool.

■Static charge removal characteristics ■Flow characteristics

0 0.1 0.2 0.3 0.4 0.5 0.6

0.1

0.2

0.3

0.4

0.5

0.6

0.7

Air pressure [MPa]

Static charge removing time [sec]

Measuring distance :50mm

Static charge removing time for supplied air pressure

0.6

0.5

0.4

0.3

0.2

0.1

100

200

300

400

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7

供給エア圧力（MPa）

除電時間（秒）

測定距離：50mm

Air pressure [MPa]

Flow rate [L/min] (ANR)

DTRY-ZPS-G11

Note1：Measuredusinga150mm,20pFchargedplatemonitor.

Note2：Thestaticchargeremovingtimeisthedecaytimefrom

± 1000Vto± 100V.

Note3：Theabovedataareactualmeasurementvalveandare

notguaranteed.

※

Be sure to read the safety precautions (common to the

ionizers) and handling instructions and precautions

(common precautions) on the website prior to using

the product.

※

DReplacement nozzle

only for DTY-ELG21

Main unit

●Do not point the tip of the nozzle at a person.

●Use safety glasses and earplugs because blowing air could blow

objects into peopleʼs eyes or cause hearing loss.

Warning

NOTE: The above data are actual measurements and are not guaranteed.

■Dimensions (mm)

■Pulse blow unit application example

Airgunionizercanbeusedasapulseblowgunsimplybyinstalling

apulseblowunit. Pulse blow unit

PAU-7W

・IN Port size :Rc1/4

・Jack size: φ6

・Non-oil speciﬁ cation (ﬂ uorine-based

quick-drying lubricant is applied)

・Operating air pressure range: 0.35 to

0.7MPa

Pulse blow unit (low pressure type)

PAU-8W

・IN Port size :Rc1/4

・Jack size: φ6

・Non-oil speciﬁ cation (ﬂ uorine-based

quick-drying lubricant is applied)

・Operating air pressure range: 0.2 to

0.5MPa

※ 1:Contact our sales representative for DTY-ELG21 performance when a pulse blow unit is

installed.

※ 2:RefertothePulseBlowSeriesCatalogNo:BK-P393fordetailedspeciﬁcationsofa

pulseblowunit.

※ 3:PulseblowunitMass66g.

DTY-ELG21

13.5

AC adapter

300±50

12.5

Power indicator

LED (green)

Error indicator

LED (red)

Operationlever

Nozzle

φ6quickﬁtting

Power cable

(140.1)

φ2 2

(3000)

24.5

φ20

(Suspension bracket 90°)

Suspension

bracket

(135.8)

24.5

φ2 2

Ionairoutlet

Replacement nozzle

Main unit

PAU-7W

PAU-8W

OUT

When a pulse blow unit is installed

URL http://www.koganei.co.jp

Limited Warranty

KOGANEI CORP. warrants its products to be free from defects

in material and workmanship subject to the following provisions.

The warranty period is 180 days from the date

of delivery.

If a defect in material or workmanship is found

during the warranty period, KOGANEI CORP.

will replace any part proved defective under

normal use free of charge and will provide the

service necessary to replace such a part.

This warranty is in lieu of all other warranties,

expressed or implied, and is limited to the

original cost of the product and shall not

include any transportation fee, the cost of

installation or any liability for direct, indirect

or consequential damage or delay resulting

from the defects.

KOGANEI CORP. shall in no way be liable or responsible for

injuries or damage to persons or property arising out of the

use or operation of the manufacturer’s product.

This warranty shall be void if the engineered safety devices

are removed, made inoperative or not periodically checked for

proper functioning.

Any operation beyond the rated capacity, any improper use or

application, or any improper installation of the product, or any

substitution upon it with parts not furnished or approved by

KOGANEI CORP., shall void this warranty.

This warranty covers only such items supplied by KOGANEI

CORP. The products of other manufacturers are covered only by

such warranties made by those original manufacturers, even

though such items may have been included as the components.

The specifications are subject to change without notice.

Warranty Period

Koganei

Responsibility

Limitations •

•

06/'20

E-mail: [email protected]

OVERSEAS DEPARTMENT

3-11-28, Midori-cho, Koganei City, Tokyo 184-8533, Japan

Tel: 81-42-383-7271 Fax: 81-42-383-7276

KOGANEI International America, Inc.

48860 Milmont Drive, Suite 108C Fremont, CA 94538, U.S.A

TEL: (+1)510-744-1626 FAX: (+1)510-744-1676

SHANGHAI KOGANEI INTERNATIONAL TRADING CORPORATION

RM2606-2607, Tongda Venture Building NO.1 Lane 600, Tianshan Road, Shanghai, China

TEL: (+86)021-6145-7313 FAX: (+86)021-6145-7323

TAIWAN KOGANEI TRADING CO., LTD

Rm.2,16F.,No88,Sec.2,zhongxiao E.Rd.,ZhongZheng Dist.,Taipei City10050,Taiwan(ROC)

TEL: (+886)02-2393-2717 FAX: (+886)02-2393-2719

KOGANEI KOREA CO., LTD

A-3001, Heungdeok IT Valley Bldg., Heungkeok 1-ro, 13, Giheung-gu, Yongin-si, Gyeonggi-do,

446-908, KOREA

TEL: (+82)31-246-0414 FAX: (+82)31-246-0415

KOGANEI(THAILAND) CO., LTD

555 Rasa TowerⅠ, Unit1207,1202, 12th floor, Phaholyothin Road, Chatuchak, Chatuchak,

Bangkok 10900 Thailand

TEL: (+66)02-513-1228 FAX: (+66)02-513-1232

KOGANEI ASIA PTE. LTD.

69 Ubi Road 1, #05-18 Oxley Bizhub Singapore 408731

TEL: (+65)6293-4512 FAX: (+65)6293-4513

Altri manuali Koganei Utensili elettrici

Koganei

Koganei DTY-ELG41 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale