Kompernass KH 5010 Manuale utente
TELEPHONE AMPLIFIER
A
KH 5010
KOMPERNASS GMBH · BURGSTRASSE 21 ·
D-44867 BOCHUM
www.kompernass.com
ID-Nr.: KH5010-12/2008-V3
TELEPHONE AMPLIFIER
Operating instructions
WZMACNIACZ SŁYSZALNOŚCI
DLA TELEFONU
Instrukcja obsługi
TELEFON HANGERŐSÍTŐ
Használati utasítás
CV_KH5010_JOE42327_LB4A 02.02.2009 9:35 Uhr Seite 1
KH 5010
6
12
3
4
5
7
9 8
0
CV_KH5010_JOE42327_LB4A 02.02.2009 9:35 Uhr Seite 5
- 1 -
Index Page
Intended use 2
Safety instructions 2
Technical data 6
Description of the device 7
Items supplied 7
Unpacking 7
Connection to the telephone 8
Establishing the power supply 8
Operation 10
Automatic switch-off 11
Troubleshooting 11
Cleaning and storage 12
Disposal 12
Warranty and service 13
Importer 15
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 1
TELEPHONE AMPLIFIER KH 5010
Read these operating instructions carefully before using the
device for the first time and preserve this booklet for later re-
ference. Pass this booklet on to whoever might acquire the
device at a future date.
Intended use
This telephone amplifier is intended for the amplification of in-
coming telephone audio signals in conjunction with a telephone.
This device is not suitable for utilisation with cordless telephones.
This device is intended for domestic use only and may not be
used for commercial or industrial applications.
Safety instructions
Risk of personal injury!
• This device is not intended for use by individuals (including
children) with restricted physical, physiological or intellectual
abilities or deficiences in experience and/or knowledge
unless they are supervised by a person responsible for their
safety or receive from this person instruction in how the de-
vice is to be used.
- 2 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 2
• Children should be supervised to ensure that they do not
play with the device.
• Turn the sound volume level down before placing the receiver
against your ear. Then increase the sound volume level as
required. Avoid a continuous or unnecessary exposure to
high sound volume levels. This could lead to hearing da-
mage.
Risk of electric shock
• Connect the power adapter only to correctly installed and
earthed mains power sockets. Check that the electricity
type and mains voltage matches the information given on
the power adapter type plate.
• Use a stabilised power adapter with an output voltage of
7 V supplying at least100 mA. When connecting a
power adapter, ensure that the polarity of the barrel con-
nector concurs with that at the jack socket.
• Do not operate the device if the mains adapter possibly
being used, the adapter's power cable or the device itself is
damaged. To avoid potential risks, arrange for the device
to be checked and, if necessary, repaired by a qualified
specialist.
• Do not expose the device to rain and never use it in a humid
or wet environment.
• ALWAYS grasp the mains adapter directly when removing it
from a mains power socket. Do NOT pull on the cable.
- 3 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 3
- 4 -
• Do NOT place any objects on the cable of the power adapter
and ensure that it cannot become snagged or trapped.
• NEVER make a knot in the power cable and do NOT bind it
together with other cables. Lay the power cable such that no
one can step on or stumble over it.
Damage to the device!
• Do not place the device on slanting surfaces, otherwise it
could slide off and become damaged in the resulting fall.
• Do not place the device at locations exposed to direct sun-
light. If you do, it may overheat and become irreparably
damaged.
Interaction with batteries
Risk of explosion!
Do not throw batteries into a fire. Do not recharge the batteries.
• Never open batteries, never solder or weld batteries.
Never short-circuit batteries. The risk of explosions and in-
juries exists!
• Remove the batteries if you do not intend to use the device
for an extended period of time.
• Regularly check the condition of the battery. Leaking batteries
can cause damage to the device.
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 4
• Always replace batteries with ones of the same type.
• Wear protective gloves in the event of having to remove a
leaking battery. Clean the battery compartment and the
battery contacts with a dry cloth.
• Keep batteries away from children. Children can put batteries
into their mouths and swallow them. If a battery is swallowed
IMMEDIATELY seek medical assistance.
Note:
Take note that the rubber pads on the device could leave traces
on painted, sensitive or treated surfaces. If possible place an
anti-slip material under the pads of the device.
- 5 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 5
Technical data
This device satisfies the fundamental requirements and other
relevant regulations of the EMC Directive 2004/108/EC.
Power supply:
Battery operation: 9V Block battery, 6F22/6LR61
(not supplied)
Operation with power adapter (stabilised):
Input voltage: 230 V ~/ 50 Hz
Output voltage: 7 V , 100 mA /
(not supplied)
Signal amplification: max. 30 dB
Plug type: 4P4C, RJ-9
Dimensions (L x D x H): 105 x 65 x 25 mm
Weight: 73 g
RJ Connectors describes the designs of plugs and sockets, as
well as their contact configurations, for telecommunication
cable installations. Most RJ Connectors are based on modular
connections, and are also designated colloquially as Western
plugs resp. sockets. A further form of designation is that of the
number of possible contact positions (“P” for Positions) and the
actually fitted contacts (“C” for Contacts).
- 6 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 6
Description of the device
1Button Tone H/L
2Sound volume LEDs
3Button Volume -/+
4Operation LED
5Socket To Handset
6Button MEM
7Battery compartment cover
8Connection socket for power adapter 7V , 100 mA/
9Socket To Phone
04P4C/RJ-9 Connector cable
Items supplied
• Telephone amplifier
• 4P4C/RJ-9 Connector cable
• Operating Instructions
Unpacking
Take the telephone amplifier from its packaging.
Remove all transport restraints and packaging materials.
- 7 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 7
Connection to the telephone
Note:
Connect the telephone amplifier with the telephone BEFORE
effecting a connection to the power source. Ensure that you
FIRST connect the receiver to the telephone amplifier and
THEN the telephone amplifier to the telephone!
1. Remove the plug of the receiver cable from the receiver
socket on your telephone.
2. Insert the plug of the receiver cable into the socket To
Handset 5 on the telephone amplifier.
3. Insert one end of the 4P4C/RJ-9 connection cable 0into
the socket To Phone 9 on the telephone amplifier and
connect the other end with the receiver socket on the
telephone.
Establishing the power supply
Battery operation
You can operate the device with a battery (not supplied).
1. Open the cover of the battery compartment 7on the
underside of the telephone amplifier.
- 8 -
IB_KH5010_JOE42327_LB4A 04.02.2009 9:41 Uhr Seite 8
Altri manuali per KH 5010
2
Indice
Lingue:
Altri manuali Kompernass Amplificatore
