Konica Minolta SD-511 Manuale utente

E-1

INSTALLATION MANUAL

A3ER-9550-00

SD-511 Saddle Stitcher

Caution:

Lifting the machine in an awkward position or

transporting it in a poorly balanced position could

result in personal injury. When transporting the

machine, assign an adequate number of persons

to the job and ensure that each person can take a

good position of not being excessively loaded.

(mass: approx. 23 kg (50-11/16))

I. Accessory parts

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly different

in shape from yours. In that case, instead of the

illustrations, use the appearance of your machine to

follow the installation procedure. This does not

cause any significant change or problem with the

procedure.

No. Name Shape Q’ty

1. Exit tray

2. Exit tray cover

3. Exit lever

4. Guide plate

5. Rail (Right)

without hook

6. Rail (Left)

with hooks

7. Screw 6

A3ERIXC001DA

A3ERIXC002DA

A3ERIXC003DA

A3ERIXC004DA

A3ERIXC005DA

A3ERIXC006DA

9654

8. Installation

manual

set

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

No. Name Shape Q’ty

4980IXC019DA

Applied Machine: FS-534

E-2

II. Installation procedures

Note:

When mounting the saddle stitcher, mount it

before mounting the finisher to the machine.

1. Turn off the machine and unplug the power cord

from the power outlet.

2. Remove the saddle unit and all other accessories

from the shipping carton and remove the protec-

tive tape and protective materials.

3. Remove the pin from the supplied exit lever.

4. Using the pin removed in step 3, attach the exit

lever to the supplied exit tray cover.

Note:

Make sure that the pin is fully inserted into the

holder.

5. If the finisher is mounted on the machine, remove

the finisher.

Note:

For the finisher removal procedure, see installa-

tion manual for finisher (FS-534).

6. Open the front door of the finisher.

7. Remove the front cover of the finisher (six

screws).

A3ERIXC032DA

A3ERIXC007DA

A3ERIXC008DA

Holder

A3ERIXC009DA

E-3

8. If the stapler unit is positioned toward the front of

the finisher, move it to the rear turning the dial

shown in the illustration.

9. Remove the C-clip from the supplied guide plate.

10. Attach the guide plate to the finisher.

Note:

Insert the two projections located at the end of the

guide plate into the holes on the plate inside the

finisher.

11. Open the guide plate and attach the C-clip

removed in step 9.

12. Remove seven screws that hold the cover

shown in the illustration on the left side of the fin-

isher.

Note:

A connector is connected to the cover.

13. Tilt the cover and remove the connector.

Remove the cover.

A3ERIXC010DA

Dial

A3ERIXC011DA

C-clip

A3ERIXC012DA

A3ERIXC013DA

A3ERIXC014DA

A3ERIXC015DA

E-4

14. Attach the supplied left and right rails. (two supplied screws each)

Note:

• Align the end of the rail with the front end of the plate of the finisher.

• Put the rail along downward to screw.

15. Plug in the two connectors and attach the exit tray cover to the finisher.

(Seven screws removed in step 12)

< Right >< Left >

A3ERIXC016DA

With hooks

A3ERIXC016DA

A3ERIXC018DA

E-5

16. Pull the left rail out completely from the finisher.

17. Hold the area of the saddle unit shown in the illustration with one of your hands and lift it. Hold the left rail

with your other hand. Fasten the saddle unit to the left rail by fitting the tab on the rail into the slot located

on the rear side of the saddle unit and then the other tab into the slot on the front side by slightly bending

the front side of the rail.

Note:

• Make sure that the guide plate described in step 11 is opened.

• Put the saddle unit close to the rail and move the saddle unit parallel to the rail. Be careful so that the

saddle unit does not come into contact with the finisher in the area A.

• When fitting the tabs on the rail into the slots, be careful not to slide the rail back into the finisher.

Caution:

• Be careful not to drop the saddle unit or hurt your fingers by the rails.

• When fastening the saddle unit to the rail, be careful not to topple the finisher.

A3ERIXC021DA

Front Rear

E-6

18. Pull the right rail out completely and fit the boss

of the saddle unit into the positioning hole on the

rail.

Caution:

Be careful not to hurt yourself while pulling the rail

out.

19. Attach the saddle unit to the rails. (one supplied

screw each for left and right)

20. Remove the screw shown in the illustration from

the front of the saddle unit.

21. Remove the screw shown in the illustration from

the back of the saddle unit.

22. Insert the three pantograph hooks of the saddle

unit into the holes on the rear inside the finisher.

A3ERIXC022DA

Boss

A3ERIXC023DA

A3ERIXC024DA

A3ERIXC019DA

A3ERIXC020DA

A3ERIXC025DA

Hook

Pantograph

E-7

23. Secure the pantograph. (one screw removed in

step 21)

24. Connect the three pantograph connectors to the

finisher.

25. Close the guide plate opened in step 11.

26. Close the front door of the finisher opened in

step 6.

27. Place the supplied exit tray on the finisher.

28. Mount the finisher to the machine.

Note:

For the finisher mounting procedures, see installa-

tion manual for finisher (FS-534).

29. Plug the power cord into the power outlet and

turn on the machine.

III. Adjustments

1. Select Finishing →Fold/Bind.

2. Make copies in finisher mode and check the sta-

tus of the Half-Fold, Center Staple & Fold and Tri-

fold.

Note:

When copying in the Center Staple & Fold mode, 5

originals need to be set on the document feeding

tray.

<Half-fold skew adjustment>

1. Unfold the paper that exits the machine and lay

the paper with the ridge facing up.

A3ERIXC026DA

A3ERIXC027DA

A3ERIXC028DA

If each mode are out of specifications,

make the following adjustments.

Exit direction

A3ERIXC033DA

<Half-Fold/

Center Staple & Fold> <Tri-fold>

Exit direction

A10DIXC049DA

E-8

2. Check the crease for deviation

(Measure width A1 and A2).

Reference: A1 - A2 = 0 ± 1.0 mm

3. Loose the two screws at the right side of the sad-

dle unit as shown in the illustration below.

4. Loose the two screws at the left side of the saddle

unit as shown in the illustration below.

5. Incline the guide plate assy shown in the illustra-

tion and adjust the skew.

Note:

Incline the guide plate assy forward or backward

according to the deviation of the crease.

[If the staple positions deviate as shown below]

Incline the guide plate assy backward.

[If the staple positions deviate as shown below]

Incline the guide plate assy forward.

6. Tighten the four screws loosen in step 3 and 4.

A10DIXC034DB

Crease

A3ERIXC029DA

A3ERIXC030DA

Screw

A3ERIXC031DB

Guide plate assy

Crease

A10DIXC039DB

A10DIXC040DB

Crease

E-9

<Half-fold position adjustment>

1. Unfold the paper that exits the machine and lay

the paper with the ridge facing up.

2. Fold the paper shown in step 1 in half and unfold

it again.

3. Check the crease for deviation

(Measure width A).

Reference: 0 ± 1.0 mm

4. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the Service Manual.)

5. Touch “Finisher.”

6. Touch “FS-FN adjustment.”

7. Touch “Half-Fold Position.”

8. Check that “ALL” is displayed in reversed.

[If the crease deviates as shown below]

Using the key, set the numeric value and

touch “OK.”

[If the crease deviates as shown below]

Using the key, set the numeric value and

touch “OK.”

9. Touch “OK.”

10. Touch “Exit” on the Service Mode screen.

11. Make copies again and check the crease posi-

tions deviate.

Exit direction

A10DIXC049DA

A10DIXC050DA

A10DIXC052DA

Crease produced in step 2

Crease

A10DIXC052DA

A10DIXC053DA

E-10

1. Unfold the paper that exits the machine and lay

the paper with the ridge facing up.

2. Check the staple position for deviation from the

crease (Measure width A).

Reference: 0 ± 1.0 mm

3. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the Service Manual.)

4. Touch “Finisher.”

5. Touch “FS-FN adjustment.”

6. Touch “Center Staple Position.”

7. Check that “ALL” is displayed in reversed.

[If the Staple positions deviate as shown below]

Using the key, set the numeric value and

touch “OK.”

[If the Staple positions deviate as shown below]

Using the key, set the numeric value and

touch “OK.”

8. Touch “OK.”

9. Touch “Exit” on the Service Mode screen.

10. Make copies again and check the staple posi-

tions deviate.

Exit direction

A10DIXC051DA

A10DIXC054DA

AStaple position

A10DIXC054DA

A10DIXC055DA

Indice

Altri manuali Konica Minolta Finisher

Konica Minolta

Konica Minolta FS-533 Manuale utente

Konica Minolta

Konica Minolta FS-518 Manuale utente

Konica Minolta

Konica Minolta Magicolor 5550 Manuale utente

Konica Minolta

Konica Minolta FS-501 Manuale utente

Konica Minolta

Konica Minolta SD-505 Manuale utente

Konica Minolta

Konica Minolta FS-523 Manuale utente

Konica Minolta

Konica Minolta FS-511 Manuale utente

Konica Minolta

Konica Minolta FS-534 Manuale utente

Konica Minolta

Konica Minolta FS-528 Manuale utente

Manuali Finisher popolari di altre marche

AGCO

AGCO Glencoe SF4800 Manuale utente

Sankosha

Sankosha DF-100E-V3 Manuale utente

Ricoh

Ricoh DDP70 Manuale utente

Canon

Canon Perfect Binder D1 Manuale utente

Canon

Canon Inner Finisher-J1 Manuale utente

Canon

Canon Inner Finisher-L1 Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Dynapac

Dynapac F1200C Guida alla risoluzione dei problemi

Lexmark

Lexmark W820 Manuale utente

Itsumi

Itsumi BT-100 Manuale utente

Fayat Group

Fayat Group DYNAPAC SC2500WS Manuale utente

Minuteman

Minuteman Orbit 20 Pro Plus Manuale utente

Dumor

Dumor Aerocard-Strike Manuale utente

SUHNER

SUHNER UTG 8-R Manuale tecnico

Kyocera

Kyocera DF-650 Manuale utente

Atlas Copco

Atlas Copco Dynapac F1800W Guida alla risoluzione dei problemi

Kyocera

Kyocera KM-3530 Manuale utente

Craftsman

Craftsman 71-24539 Manuale utente