Koolance GPU-180 Manuale utente
The video card or motherboard should be removed from the chassis in order
to install the chipset cooler. The mounting screws are inserted from the back
side of the board.
CAUTION: Removal of the original heat sink my void your
manufacturer’s hardware warranty. Please consult the manufacturer
if unsure, and keep all original parts in case of a return/RMA.
Koolance does not recommend using a liquid cooler on video cards
or motherboards that lack standard mounting holes, or have heat
sinks that are attached with only an adhesive (rather than screws or
bolts).
Beneath the board, the plastic tabs must be
squeezed together with needle-nose pliers in
order to free the original heat sink. (Some
tabs have locking center pins which must
first be removed from the top.)
Once loosened, remove the original
heat sink. Apply a thin layer of thermal
interface compound onto the chipset if
necessary.
!
Remove the protective tape from the bottom
of the chipset cooler.
To help keep them secure, place rubber
washers over the metal screws from above
the board.
Through the original heat sink
mounting holes, insert both metal
mounting screws from the back of
the board. Make sure the plastic
insulating washers are placed on
each screw.
For ATI Radeon video chipsets, place the
included adhesive foam pad around the chipset
core for a flatter mounting surface.
GPU-180 Installation Guide v 1.1
Place the liquid cooler onto the video or
motherboard chipset and align the mounting
bracket. The bracket is highly-adjustable for
proper alignment.
(NOTE: For some models of GPU-180 coolers,
you may need to re-adjust your nozzles to
provide more clearance for the bracket.)
Use the metal attachment nuts to fasten the
mounting bracket to the chipset. Hand-
tighten all video card components.
It is OK for the chipset cooler to sit
diagonally on the video card or motherboard.
Cooling efficiency will be the same.
Heat sinks are included for attachment to video
memory chips for additional cooling. Depending
on the video card, you may not require all 8 heat
sinks.
Two sets of bracket tabs are included with
the chipset cooler. Use whichever tabs
best align the cooler over the mounting
screws.
short tab long tab
(Chipset Cooler mounted on an ATI
Radeon 9800 Pro) (Chipset Cooler mounted on an
nVidia GeForce FX 5900 Ultra)
Mounting on a P-4 Northbridge Chipset
Many motherboards for P-4 chips feature heat sinks which are “hooked”
rather than bolted to the Northbridge chipset. Use the four attachment springs
included with the GPU-180 cooler to secure the bracket to this type of chipset.
Altri manuali Koolance Hardware per computer
Koolance
Koolance Exos-2 Manuale utente
Koolance
Koolance RP-985 Manuale utente
Koolance
Koolance EX2-755 Manuale utente
Koolance
Koolance ERM-3K4U Manuale utente
Koolance
Koolance CPU-360 Manuale utente
Koolance
Koolance PC4-1000 Manuale utente
Koolance
Koolance EXC-900 Manuale utente
Koolance
Koolance RP-1250 Manuale utente
Koolance
Koolance TMS-100K Manuale utente
Koolance
Koolance ALX Series Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
