Koukaam NETIO-230B Manuale utente
Warning
Unauthorized modification of this device can cause its damage!
•The manufacturer is not responsible for possible damage caused by improper usage or usage in
unsuitable environment.
•Device has been designed for indoor use only.
•Do not use the device during the strong vibrations.
•If your device does not work properly, please contact your local dealer.
Contents
1 Introduction 3
1.1 Features.............................................. 3
1.2 Specifications........................................... 3
1.3 Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Interface Description 4
2.1 SideView............................................. 4
2.2 FrontView............................................. 4
3 Installation 5
3.1 Hardware connection of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Initial Configuration 5
5 Operation and Settings 7
5.1 Outputcontrolandsettings ................................... 7
5.1.1 Outputcontrol ...................................... 7
5.1.2 Output status and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 Systemconfiguration....................................... 10
5.2.1 Configuration of network parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.2 E-mailconfiguration ................................... 11
5.2.3 Dateandtimesettings.................................. 12
5.2.4 Manageusers ...................................... 13
5.2.5 Firmwareupdate..................................... 14
5.3 Serial Port, Telnet/CGI command control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3.1 Securelogin ....................................... 14
5.3.2 Communication via KSHELL interface . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3.3 List of commands for control via KSHELL . . . . . . . . . . . . . . . . . . . . . . . 16
5.3.4 CGIcommands...................................... 19
5.4 Manualcontrol .......................................... 20
5.5 LEDstatusindicators ...................................... 20
5.6 Troubleshooting.......................................... 20
5.6.1 Reset to factory defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.6.2 Firmware upgrade problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.6.3 Fusereplacement .................................... 21
6 Liability 21
2
1 Introduction
NETIO-230B is a power controller device that can be controlled remotely via Internet browser, Telnet, or
CGI commands. Thanks to the network management technology based on the IP protocol the user can
easily control or check power status of his devices (appliances) using the computer connected to local
network or the Internet. Because of web-based management, there is no need to install any special
additional software. Telnet interface could be used for convenient automatic control by an external
device.
Imagine you are traveling abroad and you can still control your electronic appliances like computers,
servers, routers, electric entrance gates, security/surveillance systems or any other 230V appliance
directly or using the timer.
1.1 Features
•Built-in web server
•Supports wide range of Internet browsers:
•Internet Explorer
•Mozilla Firefox
•Opera
•Google Chrome
•Four switched power outputs (ports)
•Four manual control buttons
•Supported protocols: HTTP, SMTP, SNTP, DHCP, DNS and Telnet
•CGI commands control
•Secure login
•Three levels of user access
•LED indicators for actual status of each outlet
•Safe design prevents from electric current injury, fireproof materials
•Timer for scheduled output control
•Settings for power-up status of each output (on/off)
•Manual output control using buttons
•Watchdog feature for restart of unresponsive network devices
•E-mail notification
1.2 Specifications
•Input power: 230 V AC
•Max switched current: 10 A
•Latency: maximum 10 ms
3
•Latency: 300x60x90 mm (WxHxL)
•Network interface:10/100 Mbit/s
1.3 Minimum System Requirements
Computer with installed Internet browser (Microsoft Internet Explorer, Opera, Mozilla Firefox, . . . )
2 Interface Description
2.1 Side View
Figure 1: side view
1. Fuse housing for main fuse
2. Device ON/OFF switch
3. RJ-45 connector – network interface for connection to Ethernet / Internet.
2.2 Front View
1. Switched power outputs
2. Four LED indicators
4
Figure 2: front view
3. Buttons for manual output control
4. Power supply 230 V AC
3 Installation
Before the first use, please make sure that: the power supply is 230 V AC.
3.1 Hardware connection of the device
1. Connect your NETIO-230B to the computer network (switch, router) using the Ethernet cable with
RJ-45 connectors. Use cross cable when the device is directly connected to the PC.
2. Connect the power cable to power outlet.
3. Connect devices that you want to control to OUT1 – OUT4 outputs.
4. Turn on your NETIO-230B using the main switch on the side of the device.
4 Initial Configuration
1. Run file NetioDiscover.exe from the supplied CD.
2. Click on the Discover button. List of all NETIO units present in your network will appear. (figure 3)
5
Figure 3: device set-up
3. Choose the proper device from the list and click Device setup.
Window appears for set-up of network parameters - IP address, Subnet mask and Gateway. (Fig-
ure 4)
Figure 4: set-up of network parameters
After input of requested changes based on your network environment, click Change IP. Changes
are made to the device settings. Utility will update the settings of your NETIO and show device
list with changed parameters. If there is DHCP server in your network and you are not willing
to change the set-up network parameters manually, just skip to the next step. The default
IP address is 192.168.10.100 – if there is no DHCP server in the network. If a DHCP server
exists, the device gets the address from the DHCP.
4. Web management could be opened both by typing the IP address of NETIO into your internet
6
browser or by double clicking on the device name in the NETIO discover utility.
5. The login page appears. Input the User Name,Password into the login page and click OK. You
jump to the device web.
Default user name is admin, password admin
Figure 5: login page
For login to web interface, JavaScript support must run on the browser.
5 Operation and Settings
5.1 Output control and settings
5.1.1 Output control
Click on Manual Control the Menu on the left side. Output Manual control page will show up.(figure 6)
NETIO-230B can control all four outputs at the same time. Choose which ports should be turned
ON/OFF and click Apply. If you would like only to restart the devices connected to the specific ports,
tick Interrupt and then click Apply. Selected ports will interrupt for the time specified in the Status &
configuration page and then will turn on again.
Please note that you can interrupt for a short time only ports, which are turned ON. If you would
like to turn ON/OFF manually or restart, make sure that the correspondingManual checkbox is ticked. If
7
Figure 6: manual control
not, the device does not accept manual output control requests and only scheduled switching and the
Watchdog feature are in operation. PressingAll off button will turn all outputs OFF.
5.1.2 Output status and configuration
On the left side of the window, click Status & configuration, the list of ports and status information
appears in the right window.
To setup specific port select in the column Select and click Modify.
On the new page that will appear you can set up detailed parameters of this specific port. Signifi-
cance of the individual parameters is described in the following text.
Output configuration
•No.: Port number (0 - 3)
•Name: Port (Output) name
•PON state: Default output state after NETIO power on – if you tick the checkbox, the port will be
turned ON after the NETIO start or restart.
•Manual control: If you select this option it will be possible to control the output manually.
•Time control: If you select this option the port will be switched on by timer the configuration of
which is given below.
•Timer mode: Specifies how often the scheduled ON/OFF switching will be performed. Op-
tions:ONCE- event will occur only once, DAILY - event will be triggered everyday or WEEKLY -
8
Figure 7: set-up ports
Figure 8: output configuration
9
Altri manuali per NETIO-230B
1
Indice
