KP Electronic Systems BSR100D Manuale utente
ISRAEL Office:
Email: info@kpsystems.com
P.O. Box 42, Tefen Industrial Park, Tefen 24959
Tel: 972-4-987-3066 / Fax: 972-4-987-3692
USA Office: KP ELECTRONICS INC.
Email: [email protected]
109 Tudor Drive, North Wales, PA 19454
Tel: (215) 542-7460 / Fax: (215) 542-7461
Web Site: www.kpsystems.com
P.N: Book 087 Rev: New
Approved: Moshe Z. 22/05/03
BSR100D™
Wireless VHF / UHF
Radio Modem
User Manual
BSR100D™ Wireless Radio Modem Page 2 User Manual
Table of Contents
1 GENERAL DESCRIPTION
............................................................................................
4
1.1 BSR100D
F
UNCTIONS
...............................................................................................
4
1.2 F
RONT
P
ANEL
D
ISPLAY
.............................................................................................
4
1.3 R
EAR
P
ANEL
D
ISPLAY
...............................................................................................
5
2 RADIO MODULE DESCRIPTION
.............................................................................
6
3 MODEM MODULE DESCRIPTION
..........................................................................
7
3.1 D
ATA
P
ORT
I
NTERFACE
............................................................................................
7
4 PREPARING FOR OPERATION
..............................................................................
10
4.1 RF
EXPOSURE STATEMENT
.......................................................................................
1
0
4.2 C
ONNECTING
A
SSEMBLY
C
ABLES
..........................................................................
10
4.3 C
ONNECTING
PC/DTE
TO
M
ODEM
M
ODULE
......................................................
10
4.4 C
ONNECTING
P
OWER
S
UPPLY
...............................................................................
11
4.5 P
ERFORMING A
S
ELF
T
EST
.....................................................................................
11
5 SETTING COMMUNICATION PARAMETERS
...............................................
13
5.1 BSR100D™
R
ADIO
P
ROGRAMMING
G
UIDE
U
SING
GUP10™
....................
1
3
5.1.1 Operating Instructions
.....................................................
1
3
5.1.2 Connecting BSR100D to Gup10
...................................
1
3
5.1.3 Loading Parameter Values
.............................................
1
4
5.1.4 Changing Parameter Values
..........................................
1
4
BSR100D™ Wireless Radio Modem Page 3 User Manual
5.1.5 Updating Parameter Value Changes
..........................
1
4
5.1.6 Confirming Parameter Changes
...................................
1
4
5.1.7 Activating Self Test
...........................................................
1
6
5.1.8 On-Screen HELP
...............................................................
1
6
5.2 BSR100D
M
ODEM
P
ROGRAMMING
G
UIDE
U
SING
DATARADIO™
F
IELD
P
ROGRAMMING
(DFP)
S
OFTWARE
...................
16
5.2.1 Preparing Programming
.................................................
1
7
5.2.2 COM Port Settings
............................................................
1
7
5.2.3 COM Port Parameters
.....................................................
1
7
5.2.4 Primary and Secondary Port Settings Communications Modes
.....
19
5.2.5 Port Statistics
.....................................................................
20
6 TECHNICAL SPECIFICATIONS
.............................................................................
22
BSR100D™ Wireless Radio Modem Page 4 User Manual
1 General Description
The BSR100D is a data radio modem unit designed for high performance, long-
range SCADA (Supervisory Control and Data Acquisition) and telemetry
applications. The BSR100D offers the advantage of distanced communications
using long-range VHF and UHF frequencies with data modem.
1.1 BSR100D Functions
BSR100D functions include the following:
• Receives and transmits DRCMSK (Differential Raise Cosine Minimum
Shift Keying) and DF (Direct Frequency) modulation
• Performs receiving and transmitting frequency programming changes
• RSSI output
• Visual control
• Channel monitor control
• PTT control
• On/Off indicator
• Data speeds of 4800 to 19200 bps (9600bps maximum in half channels)
using a standard RS-232 interface
• Power output of 10 watt
• Half duplex or simplex operations
• Transmit control via Request-to-Send (RTS)
• Online diagnostic monitoring
• Offline local and remote diagnostics
1.2 Front Panel Display
The front panel includes three large LED indicators for radio operations, three
smaller LED indicators for modem operations and a 15-pin data port (see
Figure 1: Front Panel Display and Table 1: Front Panel LED Indication for
full explanation).
Figure 1: Front Panel Display
BSR100D™ Wireless Radio Modem Page 5 User Manual
Table 1: Front Panel LED Indication
Functionality Indicates LED Description
Push to talk (PTT) Red/Off Radio transmit/receive
mode
Channel Monitor
(CM)
Green/Red Monitors channel activity
Radio
Power Green/Red DC power
Receive (RX) Yellow Unit is receiving signal
Transmit (TX) Red Unit is transmitting signal
Modem
Power (PWR) Green DC power is applied
1.3 Rear Panel Display
The back panel includes cable connection for Tx/Rx mode with an optional
Rx plug, a 15-pin control connector and power outlet.
Figure 2: Rear Panel Display
BSR100D™ Wireless Radio Modem Page 6 User Manual
2 Radio Module Description
The BSR100D has a built in radio module that acts as a VHF/UHF transceiver
and operates as a two-way base station in half duplex mode at remote central
stations and repeaters.
The BSR100D™ has four sets of radio connectors in the rear of the unit: J1,
J2, J3, J6 (see Figure 3: Radio Connectors J1, J2, J3 & J6 and Table 2: Radio
Connector Description for full explanation).
Figure 3: Radio Connectors J1, J2, J3 & J6
Table 2: Radio Connector Description
The J6 is a D-type 15-pin panel connector that connects the following:
Table 3: J6 Pin Description
Connector Pin
PTT1 1
GND 2, 5, 7, 11, 13, 15
RS232 IN 3
RS232 OUT 4
+VB 6
METER OUT 8
NC 9, 10
AUDIO IN 12
DATA OUT 14
Connector Function
J1 BNC connector for TX/RX antenna
J2 Additional RX plug for antenna
J3 12.5 VDC power supply
J6 15-pin control connector
BSR100D™ Wireless Radio Modem Page 7 User Manual
3 Modem Module Description
The BSR100D has a built-in wireless modem that provides a high-speed data link
suitable for a wide variety of applications with system security for diagnostics
reporting.
3.1 Data Port Interface
The BSR100D modem component is equipped with a J4 15-pin data port
interface. The J4 is used for connection between the radio modem and PC for
set-up and data communications (see Figure 4: Data Port Interface).
Figure 4: Data Port Interface
Set-up and data communications require two separate cables to be used. Each
cable is labeled SET-UP or PC DATA cable and is equipped with a male 15-
pin cable connection to connect directly to the J4 interface, and a
corresponding female 9-pin COM port connector to connect to the PC.
Figure 5: Data Port Connector Diagram
Following is a detailed pin description and data port cable description:
Table 4: J4 Pin Description
BSR100D™ Wireless Radio Modem Page 8 User Manual
Figure 6: Data Port Cable Description
Table 5: Interface Signal Description
Name Description
B+ Power (input) 10 to 16 VDC (13.3V nominal maximum) 2.5A (Not
Applicable)
RX Data Receive data from BSR100D to DTE
TX Data Transmit data from DTE to BSR100D
CTS Asserted when the BSR100D is ready to accept TX data
RTS Causes the BSR100D to transmit when asserted by the DTE
DCD Asserted by the BSR100D when a data signal is being
received
Pin Name Pin Name Pin Name
1 Ground 6 Ground 11 CS 0
2 Rx Data 7 Clear to Send
(CTS)
12 CS 1
3 Tx Data 8 Request to Send
(RTS)
13 CS 2
4 Test Audio 9 Data Carrier
Detect (DCD)
14 Received Signal
Strength Indicator
(RSSI)
5 B+ Power 10 B+ Power 15 DTR
Programming
BSR100D™ Wireless Radio Modem Page 9 User Manual
DTR Data Terminal Ready. Asserted by the BSR100D Field
Programming Software to select set-up mode (Don’t connect
to this pin for user application)
Test Audio Output signal used during adjustment and testing
RSSI Output signal used during testing
BSR100D™ Wireless Radio Modem Page 10 User Manual
4 Preparing for Operation
Before installing the BSR100D™, it is suggested that the following preparations are
performed:
• Connecting assembly cables
• Connecting PC to Modem Module DTE
• Connecting power supply
• Performing a self test
4.1 RF exposure statement
Power listed is Conducted. For mobile operation, the antenna used for this
transmitter must not exceed 2 dBi and must be installed to provide a separation
distance of at least 80 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter. Installers and end-users must
be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
For Fixed Base operation, the antenna(s) used for this transmitter must not exceed 6
dBi and must be installed to provide a separation distance of at least 1.25 m from all
persons and must not be co-located or operating in conjunction with any other
antenna or transmitter. Installers and end-users must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
4.2 Connecting Assembly Cables
To connect the assembly cables:
1. Connect one end of the ρ=50 Ohm cable to J1, the Rx/Tx BNC connector.
2. Connect the other end of the ρ=50 Ohm cable to the 50 Ohm load, according
to its application wiring diagram
4.3 Connecting PC/DTE to Modem Module
To connect the assembly cables:
1. Connect the cable labeled PC DATA to the 15-pin J4 DTE connector on the
front panel of the BSR100D’s modem module (see Figure 7).
2. Connect the other end of the PC DATA cable to the 9-pin serial COM port at
the rear of the computer.
Indice
