Kramer VM-4HDCPxl Manuale utente

Altri manuali per VM-4HDCPxl

1

Indice

Altri manuali Kramer Amplificatore

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente

VM-4HDCPXL Quick Start

P/N:

2900- 301265QS

Rev:

3

Scan for full manual

VM-4HDCPXL Quick Start Guide

This guide helps you install and use your VM-4HDCPXL for the first time.

Go to www.kramerav.com/downloads/VM-4HDCPXL to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VM-4HDCPXL 1:4 DVI (HDCP) Distribution Amplifier

4 Rubber feet

1 Power cord

1 Quick start guide

Step 2: Get to know your VM-4HDCPXL

#

Feature

Function

1

POWER LED

The green LED is illuminated when the unit is turned ON

2

EDID Buttons

READ

1. To show the EDID status, press READ

2. To acquire the EDID, press the EDID SELECT button, then press READ

3

SELECT

Press to select the EDID mode (One Output, Default or Auto-mix)

4

OUTPUT STATUS LEDs (from

1 to 4)

LEDs illuminate when an output(s) is connected and active;

LEDs flash to indicate the type of EDID acquired or when a non-HDCP display is

connected while HDCP content is provided to the VM-4HDCPxl

5

INPUT DVI Connector

Connects to the DVI source

6

OUTPUT DVI Connectors

Connects to a DVI acceptor (from 1 to 4)

7

FOR PROGRAMMING 9-pin D-

sub Port

For service use only

8

Power Connector with Fuse

AC connector enabling power supply to the unit

9

POWER Switch

Illuminated switch for turning the unit ON or OFF

Step 3: Mount VM-4HDCPXL

To rack mount the machine, attach both rack ears

(by removing the screws from each side of the

machine and replacing those screws through the

rack ears) or place the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your VM-4HDCPXL.

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/VM-4HDCPXL.

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power cord to VM-4HDCPXL and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the

bottom of the unit.