Kramer AFM-20DSP-AEC Manuale utente

AFM-20DSP-AEC Quick Start

P/N:

2900- 301486QS

Rev:

Scan for full manual

AFM-20DSP-AEC Quick Start Guide

This guide helps you install and use your AFM-20DSP-AEC for the first time.

Go to www.kramerav.com/downloads/AFM-20DSP-AEC to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

AFM-20DSP-AEC 20 Port Audio Matrix

1 Set of rack ears

1 Quick Start guide

1 Power cord

4 Rubber feet

Step 2: Get to know your AFM-20DSP-AEC

Feature

Function

STATUS LED

Indicates the system’s status:

•3 cycles of red/blue/off/green LEDs

that flash in sequence for 30 seconds

when the system starts up, and the

application has not been launched.

•Flashes green when the application starts.

•Stays green when system is ready for use.

PORTS LEDs (1 to 20)

Indicate the port’s status:

•Green when an input signal is

detected, and the port is defined as

line in.

•White when defined as line out.

•Blue when defined as mic in.

•Red when in clipping state.

•Yellow when in limiting state.

•Off when there is no signal on the input.

IN OUT Dante™LEDs

(1 to 4)

Indicate the Dante’s signal status:

•Green when a signal is detected.

•Red when clipping occurs.

•Yellow when in limiting state.

•Off when no signal is detected.

HDMI™ LEDs

EMBED

Turns green when an analog audio signal is associated with the HDMI OUT signal.

Otherwise, it stays OFF.

DE-EMBED

Turns green when the HDMI IN audio signal is detected. Otherwise, it stays OFF.

IN OUT USB or S/PDIF LEDs

Indicate the USB or S/PDIF’s status:

•Green when a signal is detected.

•Off when no signal is detected.

If a signal is detected on one channel, either left only or right only, the status LED is

green.

CH 1(L)/CH 2(R) AMPLIFIER

LEDs

Indicate the amplifier’s signal status:

•Green when a signal is detected.

•Off when no signal is detected.

On the web page, CH1 and CH2 are referred to as AMP 1 and AMP 2, respectively.

Feature

Function

PORTS 3-pin Terminal Block

Connectors (1 to 20)

Interchangeable balanced mono-audio ports. Connect to an audio source or acceptor in 1

of 8 selectable I/O configurations: 16x4, 14x6, 12x8, 12x8 AEC ,10x10, 8x12, 6x14, 4x16.

Define each port as line in, mic in, mic + 48V in, or line out.

USB

AFM-20DSP-AEC can process the USB audio as a stereo speaker or operate as an audio

line-in or microphone for an audio recorder application or call conferencing.

When the AFM-20DSP-AEC is connected to a computer via USB-B:

•In the computer’s Settings > Manage sound devices > Output devices, the AFM-

20DSP-AEC USB shows as “Speaker USB AUDIO CODEC”.

•In a computer recoding application, the audio input settings for AFM-20DSP-AEC

show as “Line USB AUDIO CODEC”.

Important:

•The computer’s “Output” device (such as speakers) shows in the AFM-20DSP-AEC

embedded web pages as a USB Digital “Input”.

•The computer’s “Input” device (such as a microphone) shows in the AFM-20DSP-

AEC embedded web pages as a USB Digital “Output”.

HDMI™ OUT Connector

Connect to an HDMI acceptor to embed an audio signal from the matrix.

HDMI™IN Connector

Connect to an HDMI source to de-embed the audio signal (the video signal is passed

through to the output).

S/PDIF OUT RCA Connector

Connect to a digital stereo audio acceptor.

S/PDIF IN RCA Connector

Connect to a digital stereo audio source.

SPEAKER OUT

Outputs two selected audio signals in two channels.

•For Lo-Z: connect stereo output to Lo-Z speakers: L+ and L- to the left speaker;

R+R- to the right speaker.

•For Hi-Z (70V or 100V): connect Hi-Z and COM to mono Hi-Z speakers.

Dante PoE RJ-45 Port

Connect to Dante audio through the network. Provides 4 Tx channels and 4 Rx channels.

By default, DHCP is enabled.

RS-232 3-pin Terminal Block

Connector

Connect to a PC/serial controller to control the device.

ETHERNET RJ-45 Connector

Connect to a PC via a LAN to control the device and for firmware upgrades.

Micro USB PROG. PORT

Connect to your PC to control the device.

RESET Recessed Button

Press and hold for 5 seconds, to reset the configuration to its default parameters.

Mains Power Connector and

Fuse

Plug in for the power cord.

POWER Illuminated Power

Switch

Turns the device on and off.

Step 3: Mount AFM-20DSP-AEC

To rack mount the machine, attach both rack ears

(remove the screws from each side of the machine

and replace screws through the rack ears) or place

the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always turn off the power on each device before it is connected to the AFM-20DSP-AEC device.

For optimum range and performance, use the recommended Kramer cables available at

www.kramerav.com/product/AFM-20DSP-AEC. The use of third-party cables may cause damage!

Step 5: Connect the power

Connect the power cord to AFM-20DSP-AEC and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Operate AFM-20DSP-AEC

To operate AFM-20DSP-AEC, use:

•Embedded web pages via the

Ethernet.

•RS-232 serial commands

transmitted by a touch screen

system, PC, or other serial

controller.

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example: (adjust the amplified audio from analog audio 1 to -10dB):

#x-aud-lvl out.amplified_audio.1.audio.1,-10

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.0.0

TCP Port #:

5000

Gateway:

192.168.0.1

Username/Password

Admin/Admin

Factory Reset

Recessed Button

Press and hold for 5 seconds to reset the configuration to its

default parameters.

Protocol 3000:

“#factory” command.

Web Pages:

In the Settings page, click Factory Reset.

Altri manuali Kramer Commutatore a matrice

Kramer

Kramer AFM-20DSP-LE Manuale utente

Kramer

Kramer MTX3-34-M Manuale utente

Kramer

Kramer VP-725DS Manuale utente

Kramer

Kramer VP-16x18AK Manuale utente

Kramer

Kramer VP-747 Manuale utente

Kramer

Kramer 3232D Manuale utente

Kramer

Kramer Sierra Video 3216SXL Manuale utente

Kramer

Kramer Sierra Video 1208V3S Manuale utente

Kramer

Kramer Sierra Pro XL 1204V5 Manuale utente

Kramer

Kramer VS-5x5 Manuale utente

Kramer

Kramer 88DEE Manuale utente

Kramer

Kramer VS-606xl Manuale utente

Kramer

Kramer VP-773A Manuale utente

Kramer

Kramer VS-8 Series Manuale utente

Kramer

Kramer VS-84HN Manuale utente

Kramer

Kramer VS-88H2 Manuale utente

Kramer

Kramer VP-32x1 Manuale utente

Kramer

Kramer VS-1616DN-EM Manuale utente

Kramer

Kramer VP-88 Manuale utente

Kramer

Kramer VS-44H2A Manuale utente

Kramer

Kramer Sierra Video 3216V5 Manuale utente

Kramer

Kramer 84V5S Manuale utente

Kramer

Kramer Sierra Pro XL 1616V5S Manuale utente

Kramer

Kramer VSM-4x4A Manuale utente

Manuali Commutatore a matrice popolari di altre marche

Broadcast Tools

Broadcast Tools SS 8.2 Manuale utente

Altimium

Altimium MATF32 Manuale utente

ALFAtron

ALFAtron ALF-MUK44N Manuale utente

Monoprice

Monoprice Blackbird 15377 Manuale utente

PTN

PTN FMX12 Manuale utente

CYP

CYP nT15GX01 Manuale utente

TESmart

TESmart HMA0402A40 Manuale utente

Octava

Octava HD4XSTPMX Manuale utente

Intelix

Intelix FLX-88 Istruzioni operative

Roland

Roland XS-1HD Manuale utente

Atlona

Atlona AT-HDMI-22M Manuale utente

Link

Link HD8X8 Manuale utente

AMX

AMX AVS-OP-2020-117 Istruzioni e ricette

Lindy

Lindy 38042 Manuale utente

Extron electronics

Extron electronics MTPX Plus Series Manuale utente

Key Digital

Key Digital Champion KD-16x16CS Manuale utente

Shinybow USA

Shinybow USA SB-8811 Manuale utente

Optimus

Optimus Compact Manuale utente