Kraus KPF-1622 Manuale utente

Single Lever Pull-Out

Kitchen Mixer

KPF-1622

INSTALLATION GUIDE

Congratulations on the purchase of your new

Kraus plumbing xture!

Please keep teh box and packaging materials until your product is

completely installed. If you have any questions, require technical

assistance, or have any problems with your product:

Please contact our Customer Service Team

1-800-775-0703 / customerser[email protected]

Have the model number available, and retain a copy of your receipt

with purchase date for reference.

If for any reason this product does not meet your expectations,

please be sure to repack this product in the original box and

packaging material to avoid damage during transit.

DO NOT RETURN TO STORE

PRIOR TO INSTALLATION

• Make sure you have all necessary parts by checking the diagram and parts

list. If any part is missing or damaged, please contact Kraus Customer

Service at 800-775-0703 for a replacement

• Turn o the hot and cold water supply at the angle stops and turn on the

old faucet to release any built up pressure. Remove existing faucet. Clean

sink or countertop to remove any debris, plumber’s putty, or silicone

• Place bucket under angle stops. Turn on to ush any debris prior to

installing new plumbing. Shut o angle stops

• Pre-drilled hole size requirement: 1-3/8”

• Max countertop thickness without deck plate: 1-3/8”

Tools Required

For technical assistance or replacement parts, please contact Kraus

Customer Service and one of our representatives will be happy to help:

Toll-Free: 800-775-0703 or Customerservice@kraususa.com

Adjustable Wrench

6 5/8”

5 4/5”

3/8”

(10mm)

7/8”

19.7º(22mm)

8 5/16”

1 1/4-18UNF-2A

(21mm)

10 1/8”

(257mm)

1 3/8”

(35mm)

3 3/4”

(168mm)

(147.3mm)

(96mm)

∅ 1 3/4”

(∅ 45mm)

∅ 1 15/16”

(∅ 50mm)

9/16”-18UNEF

27mm ~ 41.3mm

1 1/16” ~ 1 5/8”

∅ 1 15/16”

(∅ 50mm)

12 7/16”

(316mm)

1 5/8”

(42.5 mm Max)

Silicone Sealant

6 5/8”

5 4/5”

3/8”

(10mm)

7/8”

19.7º(22mm)

8 5/16”

1 1/4-18UNF-2A

(21mm)

10 1/8”

(257mm)

1 3/8”

(35mm)

3 3/4”

(168mm)

(147.3mm)

(96mm)

∅ 1 3/4”

(∅ 45mm)

∅ 1 15/16”

(∅ 50mm)

9/16”-18UNEF

27mm ~ 41.3mm

1 1/16” ~ 1 5/8”

∅ 1 15/16”

(∅ 50mm)

12 7/16”

(316mm)

1 5/8”

(42.5 mm Max)

Phillips Screwdriver Safety Goggles Bucket

Diagram and Parts List

A. Faucet Body

B. Aerator Head

C. Base

D. Base O-Ring

E. Mounting Hardware Assembly

E1 Rubber& Metal Washer

E2 Mounting Nut

E3 Mounting Screws

F. Weight

G. Hot & Cold Waterlines

H. Spray Hose

I. Spacer

J. Check Valve

Included Parts:

1. Faucet Body

2. Aerator Head

3. Base

4. Base O-Ring

5. Rubber Washer

6. Mounting Nut

7. Mounting Screws

8. Weight

9. Hot & Cold Waterlines

10. Spray Hose

11. Spacer

KPF-1622 Diagram and Parts List

Aerator

Pull Out Hose

14 3/4”

810

Wrench Phillips Screwdriver

Tools you will need:

Aerator

Pull Out Hose

14 3/4”

10 12

Aerator

14 3/4”

10 12

12. Check Valve

Faucet Dimensions

7”

(179 mm)

12°

8 -1/4”

(209 mm)

9 -3/8”

(239 mm)

6 -7/8”

(175 mm)

5-3/8”

(135 mm)

2 -5/8”

(66 mm)

14 -7/8”

(377 mm)

2 -1/8”

(53 mm)

360°

Faucet Dimensions

7”

(179 mm)

12°

8 -1/4”

(209 mm)

9 -3/8”

(239 mm)

6 -7/8”

(175 mm)

5-3/8”

(135 mm)

2 -5/8”

(66 mm)

14 -7/8”

(377 mm)

2 -1/8”

(53 mm)

360°

Faucet Installation Methods

Installation Method 1

Installation Method 2

The minimum distance between

the faucet hole and wall should

be 3.5”

If the distance between the

faucet hole and the wall is less

than 3.5”, position the faucet

lever 30 degrees to 90 degrees

off the wall to allow for full

operation

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

Minimum distance 3.5

Less than

Ø35~Ø38

Ø1 ~Ø1

Step 1

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

Minimum distance 3.5

Less than

Ø35~Ø38

Ø1 ~Ø1

Step 1

Faucet Installation Methods

Installation Method 1

Installation Method 2

The minimum distance between

the faucet hole and wall should

be 3.5”

If the distance between the

faucet hole and the wall is less

than 3.5”, position the faucet

lever 30 degrees to 90 degrees

off the wall to allow for full

operation

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

Minimum distance 3.5

Less than

Ø35~Ø38

Ø1 ~Ø1

Step 1

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

nimum distance 3.5

Less than

Ø35~Ø38

Ø1 ~Ø1

Step 1

Faucet Installation Procedures

Installation Method 1

Installation Method 2 (optional)

The minimum distance between

the faucet hole and the wall should

be 3.5”

If the distance between the faucet

hole and the wall is less than 3.5,”

position the faucet lever 30° to

90° off the wall to allow for full

operation

Step 1

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

Ø35~Ø38

Ø1 ~Ø1

Step 1

Installation Steps

Step 2

Step 1

1. Remove mounting screws (9), mounting nut (8), metal washer (7),

and rubber washer (6) from the faucet body (1).

Ø35~Ø38

Ø1 ~Ø1

Step 1

Installation Steps

Step 2

Remove mounting hardware

assembly (E)

Connect waterlines (G) to hot and

cold copper lines on faucet

Step 6

Hot

Water

Cold

Water

Installer Tip

Hexagon Nut

Hot

Water

Cold

Water

Open Left

Hot Water

Push

25˚ 90˚

Step 5

KPF-1602.indd 9 2016-08-09 3:39 PM

Use two wrenches when

securing waterlines (G) to

copper lines to prevent kinking,

as shown in picture

Step 1

Step 2

t the faucet body (1) into the hole on the deck with the base

(4) and base o-ring (5), and then install the rubber washer (6),

metal washer (7), mounting nut (8) and mounting screws (9) from

underneath the sink.

Step 3

2. Insert the faucet body (1) into the hole on the deck with the base

(4) and base o-ring (5), and then install the rubber washer (6),

metal washer (7), mounting nut (8) and mounting screws (9) from

underneath the sink.

3. After adjusting the direction of the faucet body (1), tighten the

mounting nut (8) until snug and tighten the mounting screws (9) to

Step 4

Step 3

t the faucet body (1) into the hole on the deck with the base

(4) and base o-ring (5), and then install the rubber washer (6),

metal washer (7), mounting nut (8) and mounting screws (9) from

underneath the sink.

Step 3

2. Insert the faucet body (1) into the hole on the deck with the base

(4) and base o-ring (5), and then install the rubber washer (6),

metal washer (7), mounting nut (8) and mounting screws (9) from

underneath the sink.

3. After adjusting the direction of the faucet body (1), tighten the

mounting nut (8) until snug and tighten the mounting screws (9) to

Step 4

Step 3

Insert faucet body (A) into hole

on deck or sink with base (C) and

base o-ring (D) attached. Attach

mounting hardware assembly (E)

Adjust faucet body (A). Secure

mounting hardware (E) with

wrench and Phillips head

screwdriver

Step 6

Hot

Water

Cold

Water

Installer Tip

Hexagon Nut

Hot

Water

Cold

Water

Open Left

Hot Water

Push

25˚ 90˚

Step 5

KPF-1602.indd 9 2016-08-09 3:39 PM

Step 3

Step 4

Connect spray hose (H) to check

valve (J) and tighten with an

adjustable wrench.

Step 6

Hot

Water

Cold

Water

Installer Tip

Hexagon Nut

Hot

Water

Cold

Water

Open Left

Hot Water

Push

25˚ 90˚

Step 5

KPF-1602.indd 9 2016-08-09 3:39 PM

Insert washer

Step 5

Step 6

Step 4

4. Connect the spray h

with a wrench until snug

hose (12). Connect h

and tighten with a wrench, then turn on water supplies and check

leaks.

Attach weight (F) to lowest point

vertically on spray hose (H)

Connect and tighten waterlines (G)

to angle stops. Turn on the angle

stops and check for leaks

(DO NOT TURN FAUCET ON)

Step 5

Step 6

Step 4

4. Connect the spray h

with a wrench until snug

hose (12). Connect h

and tighten with a wrench, then turn on water supplies and check

leaks.

Installer Tip

Remove aerator and turn faucet on

for 60 seconds to flush any debris

Step 5

Step 6

Altri manuali per KPF-1622

Indice

Altri manuali Kraus Miscelatore

Kraus

Kraus KPF-1622 Manuale utente

Manuali Miscelatore popolari di altre marche

Bosch

Bosch GRW 9 Manuale utente

MULTIQUIP

MULTIQUIP Whiteman WM45E Guida

KitchenAid

KitchenAid KSM7581BZ0 Guida rapida

Jay-Lor

Jay-Lor 5050 Manuale utente

Sunbeam

Sunbeam FPSBSM210X Manuale utente

MULTIQUIP

MULTIQUIP Whiteman MC94S Guida

Thinky

Thinky ARE-250 Manuale utente

Midas

Midas XL4 Manuale utente

bianco

bianco PURO 4 Manuale utente

Paso

Paso DAG9200 Manuale utente

Sima

Sima SFX-9A Manuale utente

better chef

better chef IM-815WC Istruzioni per l'installazione

ALLEN & HEATH

ALLEN & HEATH GR1 Manuale utente

Lacor

Lacor 69083 Scheda tecnica

M-Audio

M-Audio Midiman SAM Manuale utente

Buffalo

Buffalo CP921 Manuale utente

Pentair

Pentair HYPRO Cleanload 3376-0870 Istruzioni operative

Cuisinart

Cuisinart SM50WHE Manuale utente