KRUG+PRIESTER EBA Series Manuale utente
EN Operating InstructionsGuillotines
www.eba.de
EBA 5560
- 2 -
Table of Contents
Safety precautions 3
Intended use 4
Installation 8
Startup 9
Operation 12
Operating elements 16
Blade and cutting stick replacement 24
Maintenance and cleaning 35
Annual inspection / Safety test 37
Possible malfunctions 38
Accessories 42
Technical data 43
EC-declaration of conformity 46
- 3 -
Safety precautions
Please read these operating instructions before putting the machine into
operation and observe the safety precautions.
The operating instructions must always be available.
Children must not operate the machine!
Do not reach beneath the blade!
Never leave the blade unattended!
Do not extract or transport the blade without
protection! (See page 27 and 29).
Danger! Risk of injury!
Do not cut hard materials or materials which
may splinter!
- 4 -
Intended use
The machine is designed for cutting stacks of
paper to a specied size.
This machine is constructed for "one-man
operation" only!
Warning! Clips or similar damage the
cutting blade.
Safety precautions / Intended use
Do not use any spray cans with flammable
content near to the cutting machine!
Do not use any flammable cleaning agents.
- 5 -
Disconnect from the mains before starting any
service work or before removing the panels!
Replacement of blade and cutting stick may
be performed only when the main switch is
switched off!
Safety precautions
- 6 -
B
A
B
A
Protect mains cable against heat, oil and
sharp edges!
Standard machines are factory-set as
follows:
• Voltage 230 V (120 V) 1 phase
• Frequency 50 Hz (60 Hz).
All components which could endanger the
operator are covered by a guard (B)!
Do not operate the machine without the
following safety devices:
• Safety beam guard (A)
• Panels, tightly screwed (B).
The cutting action, which is dangerous to the
operator, is protected by a two-handed
control system (B) and safety beam guard
(A).
Safety precautions
- 7 -
When not in use for a longer period switch
off. (Main switch to "0").
Danger!
Blade must always be covered by the
pressing bar.
Clamping Blade
OK
OK
Safety precautions
- 8 -
A
A
B
The machine is mobile on castors. Align the
machine as followes:
• Align machine with water level and adjust
accordingliy.
4 x screws size 19 (A).
• Reference area machine table (B).
Installation
- 9 -
A
The machine is delivered ready for
operation. Side tables (A), left and right are
available as an option. Assembly
instructions are included.
Startup
Plug into socket.
Installation / Startup
- 10 -
B
A
C
DE
STOP
The machine may only be operated, if
the operating instructions and the safety
instructions have been understood.
Before each use, check the safety
equipment for completeness and
functionality.
• All covers have to be mounted (A).
• Safety beam guard must be mounted (B).
• The release for cutting is allowed only if
the two-hand safety device is operated at
the same time (C)
• Safety light beam:
If the test rod (E, tool kit) is held into
the
protectiveeld(D),anactivatedwork
cycle must be stopped immediately.
We recommend you keep a record of your
test results.
Startup
Altri manuali per EBA Series
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali KRUG+PRIESTER Taglierina
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 6655 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 5560 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER EBA 5255 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 5560 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 5255 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 4855 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 4860 ET Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER EBA 4855 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 4705 Manuale utente
KRUG+PRIESTER
KRUG+PRIESTER IDEAL 1138 Manuale utente
