KUHN CONTROLOR Manuale utente

CONTROLOR

9CT504 - GB - 03/2003

INSTRUCTIONS MANUAL

Contents

EQUIPMENT IDENTIFICATION ......................................................................................... 3

SYSTEM DESCRIPTION ....................................................................................................... 4

ASSEMBLY INSTRUCTIONS ................................................................................................ 6

UTILISATION ............................................................................................................................ 8

KEYDESCRIPTION............................................................................................................. 8

STARTINGUPTHE DEVICE: START KEY .......................................................................... 8

PROGRAMMINGTHEDEVICE: PROGRAMMING KEYS .................................................... 8

WORKINGWIDTHKEY 9

PULSES OVER 100 METRES KEY 10

NUMBEROFROWSANDROWPROGRAMMINGKEY 11

NUMBER OF SEEDS / HECTARE KEY 12

OPERATING THECONTROLUNIT ................................................................................... 13

SEEDCOUNTINGOPERATION 13

INFORMATIONKEYS 13

STARTKEY 13

TRIP AREA KEY 13

TOTAL AREA KEY 13

HECTAREOUTPUTKEY 14

TIME KEY 14

DISTANCEKEY 14

MOTIONSPEEDKEY 14

TURBINE AND CELL TEST KEY 14

KEYS FOR MODIFYINGTHE NUMBER OFROWS WHILE WORKING 15

EXAMPLE OF USE OF THE CONTROLOR CONTROL UNIT ................................... 16

STARTINGUPTHECONTROLORCONTROLUNIT............................................................ 16

PROGRAMMINGTHEWORKINGWIDTH.......................................................................... 16

PROGRAMMINGTHE NUMBEROF PULSES OVER100 METRES. ................................ 16

PROGRAMMINGTHENUMBER OFSEEDS / HECTARES............................................... 17

PROGRAMMINGTHE NUMBEROF ROWS. .................................................................... 18

USEOFTHE WHITEINFORMATIONKEYS. ..................................................................... 19

MAINTENANCE ..................................................................................................................... 21

CONTROLUNIT ................................................................................................................. 21

OPTOELECTRONICSENSORS......................................................................................... 21

TROUBLESHOOTING ....................................................................................................... 22

NOTES ...................................................................................................................................... 23

WIRING THE CONTROLOR CELL .................................................................................. 24

CONTROLOR WIRING DIAGRAM................................................................................... 25

STANDARD GUARANTEE CONDITIONS...................................................................27

EQUIPMENT IDENTIFICATION

IMPORTANT

NOTE THE SOFTWARE VERSION OFYOUR DEVICE (DISPLAYED FOR 1 SECOND

ON THE DISPLAY WHEN THE DEVICE IS SWITCHED ON)

IT WILL BE REQUIRED IN ANY CORRESPONDENCE ABOUT THE DEVICE

IMPORTANT: This manual (9ct503 - F ) applies to software versions from 13/08/99.

SYSTEM DESCRIPTION.

Black keys = making changes while working.

White keys = information.

Red keys = data programming.

3 21213

5 41415

7 61617

9 8 18 19

10 11 20 21

1 Display 11 -

2 Off 12 Row control left On/Off

3 On 13 Row control right On/Off

4 Total area 14 Hectares seeded/hr

5 Trip area 15 Number of rows

6 Distance covered 16 Speed

7 Working time 17 Number and programming of rows

8 Working width 18 Pulses over 100 metres

9 Turbine and cell test 19 Number of seeds / Hectares

10 + 20 Enter

21 Control (reset))

INDEX

The seeding controller has two programs:

1 – A seed counting program using optoelectronic sensors for precision seed drills (maximum 12 rows).

2 – A program including counters to count the area, time, distance and speed.

The device is made up of the following:

- A control unit installed in the tractor, which is used to enter data and control the seed drill. The unit generates

audio and visual alarms in the event of problems.

- Cable form connecting the control unit and the sensors.

- Optoelectronic sensors fitted on each seeding element.

- A rotation sensor installed on its support on the seed drill rotating shaft.

1 – Using the controller to count the seed with the optoelectronic sensors

When seed goes past the optoelectronic sensor, a pulse is sent to the computer, which determines and displays the

number of seeds per hectare for each row. If the value is less than 15% of the setting entered by the user, the

controller generates an audio and visual alarm. If the difference is less than 15%, there is no alarm.

While sowing seed with a diameter of less than 3 mm (e.g. rape seed), reduce the alarm limit so that the control unit

only monitors that seed is being delivered (no counting facility in this case).

2 – Using the controller for other counting functions

When the counter is displayed, an arrow is displayed above the corresponding symbol.

Counters are available for the following:

- seeded area and total area with the tool in the working position

- speed

- working time

- output per hectare

- distance.

ASSEMBLY INSTRUCTIONS

- 1 – Computer.

The computer is to be fitted with its support in the field of vision of the driver.

Keep a distance of at least one metre between the computer and transmitters (CB or other) or transmission antennas.

- 2 – 12 volt connection to the battery.

The computer must be connected directly to the battery. No other device may share this connection.

Protect the power supply with a 25-Amp fuse.

- 3 – Colours of connections

BROWN = 12V

BLUE = earth

- 4 – Cable form.

The cable form and sensors are installed in the factory.

For subsequent modifications, see page 25 for the wiring diagram of the unit.

- 5 – Optoelectronic sensors

The optoelectronic sensors are fitted on the seeding elements. The connection is made via a 4-pin connector.

When seen from behind, the row to the far left is row 1.

Wire colours:

WHITE = earth

BROWN = + 12 volts

GREEN = signal

YELLOW = signal for shunt connector

IMPORTANT:

- While modifying a seed drill, make sure to replace any BNN0082 ejectors with the BNB0083 model (different

ejection height) supplied with the control unit cell.

- Make sure that the seal is in place on the connector of the optoelectronic sensor. Keep the cables safe from

friction and other harmful influences.

- Handle the cell support with care. Any deformation would misalign the cells and lead to system

malfunctioning.

Ejector

- 6 – Rotation sensor.

The magnet is fitted on the hexagonal drive bar of the seed drill and must be

opposite the sensor. The sensor must be fitted at a distance of about 5 to 10

mm from the magnet (diagram opposite)

- 7 – Modifying the number of rows.

Proceed as follows to modify the seed drill, say from 8 rows to 6 rows:

- stop the control unit

- disconnect the optoelectronic sensor (4-pin connector) from the rows to

be removed

- replace the connector of the optoelectronic sensor with a shunt connector

(see page 25)

- on the control unit, change the number of rows, working width and

programming.

- 8 – Adding rows to the seed drill.

In order to add rows to an existing seed drill, you can add cells to the form, in accordance with instructions NT0006500

(attached).

PRECAUTIONS:

PRECAUTIONS FOR USE.

This devices is intended for farming machinery only.

Other uses are not covered by the guarantee.

ELECTRICAL PRECAUTIONS.

Before starting to work on the electronic system of the tractor or seed drill, first disconnect the seeding control unit

from the battery.

That is also indispensable during welding work on the tractor or tool.

5 - 10 mm

UTILISATION

KEY DESCRIPTION.

The keys are of three colours:

Red keys: programming

White keys: information (value display)

Black keys: On/Off or modifying the number of rows while working

1 – Starting up the device: Start key

Use keys and to start up the device and switch if off.

When the device is turned on, the software version is displayed briefly. The unit then goes through the set-up procedure

and automatically displays the last function used before the unit was switched off.

If the power supply voltage drops below 9 volts, the device is turned off automatically.

If there is an electronic fault, the unit displays either HALP 00 or HALP 88

In that case, it must be returned for repairs.

2 – Programming the device: Programming keys

Keys “ +/- ”

Used to change the values of the programmed data.

For the electronic control box to calculate the various values displayed, the following data are required.

- pulses over 100 metres

- working width

- number of rows

Working width key

- press the « working width » key

- display the value with keys « + / - »

- press Enter to save or validate

Then check the working width by pressing

« the working width » key once again :

Example:

You have a 6-row drill with 0.45 m spacing, i.e. a working width of 2.70 m,

- press the working width key

- display 2.70 m using key + or -

- press Enter to validate

Pulses over 100 metres key

This key is used to enter the number of pulses the rotation sensor indicates over a distance of 100 metres on the

computer.

There are two ways of entering this information:

1 ) The theoretical value of the pulses over 100 metres is 64 for our seed drills

-press the Pulses over 100 m key

- display the value using keys « + or - »

- press « Enter » to save

2) You want maximum precision in all land (soft, light etc.):

- reset the number of rows to zero (see page 11)

- measure an accurate distance of 100 metres and mark it out.

- place the machine opposite the first marker.

- press the Pulses over 100 mm key and at the same time.

- cover the 100-metre distance at the normal working speed.

- press Enter when you go past the 2nd marker to save the setting.

Indice

Altri manuali KUHN Controllori

KUHN

KUHN TKS Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente