Kuzar K-1 Manuale utente
KUZAR SYSTEMS S.L. Version.14/9
English - User Manual
Español - Manual de Usuario
Deutch - Bedienungsanleitung
English - User Manual
Español - Manual de Usuari
o
Deutch - Bedienungsanleitu
ng
2
K-1
Made in Spain (EU)
125 kg (275.6lb)
3.8 m (12.5’)
KUZAR SYSTEMS S.L.
C/ Ciudad de Ferrol Nº8
Pol.Ind. Fuente del Jarro
46988 Paterna - Valencia (Spain)
Manual de usuario propiedad de KUZAR SYSTEMS S.L. Deposito legal y copyright 2014.
Todos los derechos reservados.
3
1302
1301
1303
4001
1201
2102
2103
1001
7001
Tornillo / Screw
Tuerca / Nut
2104
Tapón tirante/
Strap cap
Tramo 1 Base / Section 1
Tramo 2 / Section 2
Tramo 3 / Section 3
A
B
C
Pata / Leg
Tirante/ Strap
Tapón pata/
Leg cap
Cabrestante / Winch
4
1007
1007
1007 8002
8002
8002 1102
2002
1008
1103
2110
2182
A.1
1012
1006
A.1 - Despiece / Breakdown
8003
7002
A.1
Gatillo / Lock
Tornillo / Screw
Tornillo / Screw
Contera / Bracket
A
5
2105
2109
2107
2101
1002N
7001
Tornillo / Screw
Tuerca / Nut
2106
1004
3001
2001
1010
1101
1005
1005
Soporte fijo tirantes /
Fixed strap support
Tapón superior pata/
Leg upper cap
Pomo soporte patas /
Leg support knob
Soporte patas /
Leg support
Gatillo / Lock
7001
Tuerca / Nut
1001
Tornillo / Screw
C
B
C.1 - Reenvío inferior Tramo 2 (Ref.1302) / Lower pulleys set Section 2
6
9001
2111
4001
1003
8001
Tornillo / Screw
Arandela / Washer
7001 Tuerca / Nut
1009
2003
7002 8004
8003
9001
D.1 - Despiece / Breakdown
D
2131
1006
Tornillo / Screw
Prolongador /
Extension bar
Prisionero cable /
Cable clamp
Cable acero /
Steel cable
Cable
Cabrestante /
Winch
D.1
7
Code/Código Description/Descripción
1001 M8x55 hexagonal screw / Tornillo hexagonal M8x55
1002N M8x25 hexagonal screw / Tornillo Hexagonal M8x25
1003 Allen screw M8x16 / Tornillo allen M8x16
1004 Conic allen screw M5x12 / Tornillo allen cónico M5x12
1005 Conic screw M6x16 / Tornillo cónico M6x16
1006 Allen screw M10x25/ Tornillo allen M10x25
1007 Allen screw M6x20 / Tornillo allen M6x20
1008 Special M10 screw / Tornillo especial M10
1009 Hexagonal screw M10x40 / Tornillo hexagonal M10x40
1010 Conic screw M4x35 / Tornillo cónico M4x35
1012 Allen screw M6x10 / Tornillo allen M6x10
1101 10mm axel plate / Pletina eje 10 mm
1102 Pletina portapolea / Pulley support plate
1103 K-1 threaded pulley cover plate / Pletina roscada portapoleas K-1
1201 Leg K-1 / Pata K-1
1301 Section 3 K-1 / Tramo 3 K-1
1302 Section 2 K-1 / Tramo 2 K-1
1303 Section 1 (Base) K-1 / Tramo 1 (Base) K-1
2001 Pulley Ø 50 / Polea Ø 50
2002 Pulley Ø 40 (Upper pulley support K-1) / Polea Ø 40 (Portapoleas superior K-1)
2003 Pulley Ø 40 (Cable entry) / Polea Ø 40 (Entrada cable)
2101 Upper leg tap / Tapón superior pata
2102 Ground leg tap / Tapón pata suelo
2103 Leg strap / Tirante patas
2104 Strap tap / Tapón tirante
2105 Sliding leg support / Soporte patas deslizante
2106 Fixed strap support / Soporte fijo tirantes
2107 Short lock for sliding leg bracket / Gatillo corto para soporte deslizante patas
2109 Knob for sliding leg bracket / Pomo soporte deslizante patas
2110 35x35 mm Bracket / Contera 35x35 mm
2111 Cable clamp screw Ø4 mm / Prisionero cable Ø4 mm
2131 Extension bar / Barra de extensión
2182 KAT Lock K-1 / Gatillo KAT K-1
3001 10x50 axel / Eje 10x50
4001 450 kg winch / Cabrestante 450 Kg
7001 Auto-block nut M8 / Tuerca autoblocante M8
7002 Auto-block nut M8 / Tuerca autoblocante M8
8001 Flat M8 washer / Arandela plana M8
8002 M6 washer / Arandela M6
8003 Flat M10 washer / Arandela plana M10
8004 M12 washer / Arandela M12
9001 Cable K-1 (Ø4 mm) / Cable K-1 (Ø4 mm)
LISTA DE REPUESTOS / SPARE PARTS LIST
8
K-1
Operating Instructions - ENGLISH
1 - INTRODUCTION.
Dear user. Thank you purchasing your Kuzar K-1 lifter. We hope you will be very satisfied
with it.
This manual has been written so that you can understand how to effectively use the lift
and most importantly, so that you can use it safely.
It is important that you fully read the manual and follow the instructions carefully before
using your lift. All Kuzar lifts undergo a very strict quality control process during their
manufacture. So that your lift always works properly please only purchase original Kuzar
parts from an authorized distributor or dealer. The user waives all warranty rights if using
parts other than Kuzar or if the product is manipulated in any way by an unauthorized
third party. When requesting parts, please refer to the diagrams in the back of this ma-
nual and quote the serial number and year of manufacture located on your lifter.
2.- TECHNICAL SPECIFICATIONS.
Kuzar lifter, model K-1 has been designed for vertically lifting lighting, trussing etc in the
Professional sound and light sector. For various Kuzar supports available please refer to
our website www.kuzar.es or catalogue.
2.1 - Max. load: 125 kg (275.6 lb).
2.2 - Min. load: 25 kg (55 lb).
2.3 - Max. height: 3.2 m (10,5’) (with extension bar 3.8m (12,5’))
2.4 - Folded. height: 1.26 m (4,1’)
2.5 - Work surface: 1.50 x 1.50 m (4,90’ x 4,90’)
2.6 - Weight: 21 kg (46 lb)
2.7- Winch: 450 kg certified.
2.8 - Cable: Steel DIN 3060. Tensile strength 180 kg/mm2. Anti-torsion & anti-corrosion
4 mm cable diameter.
2.9 - Construction material: Steel profiles EN 10305.
2.10 - Three-profile telescopic system operated by steel cable driven by pulleys with
metal protected bearing pads. Adaptor Ø35 mm.
2.11 - Antirust protection priming paint bathed black steel, covered with cured polyester
dust.
9
K-1
Operating Instructions - ENGLISH
3 - SAFETY GUIDELINE.
3.1.- Situate the tower on a solid and flat surface.
3.2.- Check that the support system is fixed by the security trigger and that the tower is
in a upright position.
3.3.- Check that the tower is locked in its working position with the safety lock.
3.4.- When used outdoors, place the tower on a hard surface and if necessary secure it
against excess wind force via cable braces.
3.5.- Do not use ladders nor lean them against the lifter.
3.6.- Be careful with any cables, prominent objects etc. placed above the tower.
3.7.- Do not stand underneath the load.
3.8.- Do not move the tower when it is elevated or loaded.
3.9.- Before using the tower, check the condition of the cable. This must be free of cuts
and frays. Never use damaged cables.
3.10.- Never dismount the winch handle or any element of the winch under any circum-
stance.
3.11.- Once the tower is set-up in its working position we recommended the winch handle
is locked to avoid anyone interfering with it.
3.12.- The minimum load for a safe operation of the brake is 25 kg. The brake will not
function without this minimum load.
3.13.- Do not grease or lubricate the brake mechanism of the winch.
3.14.- This lift cannot lift human beings.
3.15.- For transportation it is necessary to retract all profiles and lock them with the co-
rresponding safety lock.
4.- OPERATION.
4.1.- Place the tower on a flat and solid surface where it is going to be used.
4.2.- Unlock the safety lock from the legs support system. Slide the support system
downwards until the lock has reached the required position.
4.3.- Attach the load to the tower using the desired support (the support varies upon the
application), and ensure it is only used to lift loads vertically. The minimum load is 25 kg.
4.4.- Elevation: Extend the tower by turning the winch handle clockwise, lifting the load
to the desired height.
10
K-1
Operating Instructions - ENGLISH
4.5.- Hold: Release the winch handle, it will remain in position by the action of the
winch’s automatic brake. Ensure the KAT lock has introduced in to the profile by turning
the handle slightly anti-clockwise.
4.6.- Continue elevating: Turn the winch handle again clockwise and lift the load until
the second profile is fully extended. Release the handle which will remain fixed by the
winch’s automatic brake and proceed to ensure that the KAT lock has introduced into the
second profile by turning the handle again anti-clockwise. The tower can be stopped in
any desired intermediate position. Simply release the winch handle and secure the tower
by inserting the corresponding KAT lock into the hole which is closest to the required
position.
4.7.- Descent: Descending the load follows the same procedure but in reverse. Firstly
unlock the KAT lock and turn the winch handle anti-clockwise, until the first profile is com-
pletely folded down. Now unlock the next KAT lock and retract the second profile. Just as
when lifting the load, the lift may be stopped at any intermediate position.
4.8.- Transport: When transporting / carrying the lift it is necessary to fold the tower by
retracting all the profiles completely. Then close the sliding support piece and fix it with
the safety lock and tightening the knob.
5.- MAINTENANCE.
5.1.- All cables must be checked regularly. Faulty cables must be replaced immediately.
Do not use the lifter with faulty cables as it is potentially very dangerous. Only use DIN
3060 cables, supplied from an authorised dealer.
5.2.- The lifter is delivered ex factory completely greased. Depending on its mechanical
use though, we recommend that the crown wheel of the winch, the pads & bushings of
the drive shaft, the handle thread and the profiles of the lift are periodically greased.
ATTENTION:
Do not apply oil or grease to the brake mechanism.
The brake discs have been pre-greased with a special heat and pressure resistant grea-
se. To avoid malfunction to the winch brake, no other products must be used except the
original provided by the company. It is not necessary to grease the brake discs.
Altri manuali per K-1
1
Indice
Lingue:
Altri manuali Kuzar Rack e supporto
