La Crosse Technology WT-5442 Manuale utente

QUICK SET-UP GUIDE

1) Insert two AA batteries into the remote transmitter.

2) Insert three AA batteries into the projection alarm and/or plug into wall.

Note: When starting or restarting your projection alarm the remote transmitter

must be started first and then your alarm. After power is supplied (either battery

or AC) ensure that no buttons are pressed for 10 minutes. This will allow time for

the projection alarm to communicate with the remote transmitter as well as

receive the WWVB signal.

Note: When using the AC adaptor, plug into the projection alarm first and then

into the electrical outlet (this will help avoid pressing any buttons inadvertently).

3) Wait 10 minutes for WWVB reception and remote temperature.

4) If there is no WWVB reception, manually set the time and date (instructions

in the Program Mode).

5) Program the settings.

6) Mount the WT-5442 in a suitable location, where WWVB and transmitter

signals can be received.

7) Mount the transmitter where remote temperature measurement is desired (on

the North side of a house for example).

Note: The remote transmitter is weather resistant but not water proof. High

humidity and mist will not damage the transmitter but direct rain will. The

maximum range between the transmitter and projection alarm is 80ft. open air (no

obstructions). Any resistance (i.e. walls, furniture, etc) between the two will

decrease the effective operating range.

8) The projector will activate and remain on if the alarm clock is plugged in. If

only batteries are used, the projector will only be activated when a button is

pressed.

9) See the “Features” section III. for instructions on projection direction, etc.

WT-5442

433 MHz

Radio Controlled Projection Alarm

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

About WWVB 3

Quick Set-Up Guide 4

Detailed Set-Up Guide

Battery Installation 5

Program Mode

Programming Sequence 6

Function Buttons 6

Time Zone Setting 7

DST (Daylight Saving Time) Setting 7

Adjustable Snooze 8

Time Setting 8

Date Setting 8

12/24-Hour Setting 9

Selecting °F or °C 9

Features & Operations

Features 10

Radio-Controlled Time 10

Projection 11

EL Backlight 11

Indoor Temperature 11-12

Remote Temperature 12

Time Alarm 12-13

Changing Display Mode (viewing seconds) 13

Weather Forecast 14

Mounting 15

Maintenance & Care 15

Troubleshooting 16

Specifications 17

Warranty and Contact Information 18

INVENTORY OF CONTENTS

1) WT-5442 Alarm Clock

2) TX6U Remote temperature sensor

3) AC adapter/transformer

4) Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1) Three fresh 1.5V AA batteries (optional for alarm clock)

2) Two fresh 1.5V AA batteries (for remote sensor)

Note: Alkaline batteries are recommended for use in both pieces.

FEATURES OF PROJECTION ALARM

Operation of these features are in section III.

1. Radio-controlled time and date

2. Projection of time and/or remote temperature

3. EL backlight

4. Six modes of date/seconds/temperature display

5. Indoor temperature

6. Remote outdoor temperature

7. Dual alarms

1) Adjustable snooze

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits

the exact time signal continuously throughout the United States at 60 kHz. The

signal can be received up to 2,000 miles away through the internal antenna in the

Projection alarm. However, due to the nature of the Earth’s Ionosphere,

reception is very limited during daylight hours. The Projection alarm will search

for a signal every night when reception is best.

The WWVB radio station receives the time data from the NIST Atomic clock in

Boulder, Colorado. A team of atomic physicists is continually measuring every

second, of every day, to an accuracy of ten billionths of a second per day. These

physicists have created an international standard, measuring a second as

9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For more detail,

visit http://www.boulder.nist.gov/timefreq.htm. To listen to the NIST time, call

(303)499-7111. This number will connect you to an automated time, announced

at the top of the minute in “Coordinated Universal Time”, which is also known as

Greenwich Mean Time (GMT). This time does not follow Daylight Saving Time

changes. After the top of the minute, a tone will sound for every second. It is

possible that your Projection Alarm may not be exactly on the second due to the

variance in the quartz. However, the clock will adjust the quartz timing over the

course of several days to be very accurate; under 0.10 seconds per day.

QUICK SET-UP GUIDE

1) Insert two AA batteries into the remote sensor.

2) Insert three AA batteries into the projection alarm and/or plug into

wall.

Note: When starting or restarting your projection alarm the remote

sensor must be started first and then your alarm. After power is supplied

(either battery or AC) ensure that no buttons are pressed for 10 minutes.

This will allow time for the projection alarm to communicate with the

remote sensor as well as receive the WWVB signal.

Note: When using the AC adaptor, plug into the projection alarm first

and then into the electrical outlet (this will help avoid pressing any

buttons inadvertently).

3) Wait 10 minutes for WWVB reception and remote temperature.

4) If there is no WWVB reception, manually set the time and date

(instructions in the Program Mode).

5) Program the settings.

6) Mount the WT-5442 in a suitable location, where WWVB and sensor

signals can be received.

7) Mount the sensor where remote temperature measurement is

desired (on the North side of a house for example).

Note: The remote sensor is weather resistant but not waterproof. High

humidity and mist will not damage the sensor but direct rain will. The

maximum range between the sensor and projection alarm is 80ft. open

air (no obstructions). Any resistance (i.e. walls, furniture, etc) between

the two will decrease the effective operating range.

8) The projector will activate and remain on if the alarm clock is plugged

in. If only batteries are used, the projector will only be activated when

a button is pressed.

9) See the “Features” section III. for instructions on projection direction,

etc.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE TEMPERATURE SENSOR

1. Remove the battery cover.

Observing the correct polarity,

install 2 AA batteries. The

batteries will fit tightly (to avoid

start-up problems make sure that they do not spring free during

installation).

2. Replace the battery cover.

B. PROJECTION ALARM

1. Remove the battery

cover.

2. Observe the correct

polarity, and install 3 AA

batteries.

3. In addition or instead of

inserting batteries, the

AC adapter can be used. Simply plug the adapter into the receptacle

on the underneath of the alarm clock and then plug the adapter into

the outlet.

4. Replace the battery cover.

5. The projector will activate and remain on if the alarm clock is plugged

in. If only batteries are used, the projector will only be activated when

a button is pressed. The projection is a red light, not harmful under

normal usage, although care should be taken to not look directly into

the light.

Note: After power has been supplied (battery or AC) a tone will

sound, and the LCD (Liquid Crystal Display) will activate. The indoor

temperature and the remote temperature will be displayed (within

three to six minutes). Also, the time will appear as “-:--”. The WWVB

search is automatically initiated, and a tower icon appears and

flashes with the time colon (no tower icon will appear if the WWVB is

too weak to be detected, which is typical during daylight hours and

the time display will remain on “-:--”). While the WWVB search is

being conducted various numbers will appear in the time display.

After 10 minutes, the Projection Alarm will either display the WWVB

time, or discontinue the search if the time is not found. If the search

is cancelled “-:--” will remain in the time LCD. The Projection Alarm

will conduct a WWVB search every hour until the first signal is found.

Once the WWVB time is found, a search is automatically conducted

nightly at midnight. If the signal is found at midnight, the tower icon

will remain, if not, another search will take place every hour (until

6:00 am) until the signal is found successfully. If no signal is found

during this period, the tower icon will not appear and the clock will

search again at 12:00 am the next night.

II. PROGRAM MODE

To enter the Program Mode hold down the “SET” button for 1 second, until

the time zone (“-5” default) flashes in the lower left. The Program Mode

Guide is laid out in a manner that allows you to program each function

separately, or you can follow the instructions entirely to program the

Projection alarm. Complete programming is usually done for the initial

set-up, and will require you to skip step 1 of programming sections “D”

through “H”.Press the “SNOOZE” button at any time to exit the Program

Mode, or wait approximately 15 seconds for the Projection Alarm to

automatically return to normal operation.

A. PROGRAMMING SEQUENCE

Default (Factory) Setting

1. Time Zone Setting -5 (eastern standard time)

2. Daylight Saving Time ON/OFF ON

3. Adjustable Snooze 10 Minutes

4. Hour Setting 12: AM

5. Minute Setting :00

6. Year Setting 01 (2001)

7. Month Setting 1 (January)

8. Date Setting 1

9. Day Setting MO (Monday)

10. 12/24-hour Mode 12-hour

B. FUNCTION BUTTONS

There are 8 function buttons;

three on the front, four on the

back and one on the top of

the projection alarm. The

function buttons are labeled:

ALM1/HOUR, ALM2/MIN,

light intensity icon, DISPL,

light direction icon, SET,

MODE/+, and SNOOZE (the

top bar).

C. TIME ZONE SETTING

1. Hold down the “SET” button for 1 second, the time zone (“-5” default)

will flash in the Date LCD.

2. Press and release the “Mode/+” button to select the appropriate time

zone. There are 13 time zones to choose from based relative to the

international time standard of GMT (“Greenwich Mean Time”)(shown

as “0h” on display).

3. From –5h to –8h, a US map with the highlighted time zone will also

be displayed to the right of the time display.

4. Press and release the “SET” button to confirm the time zone setting,

and to advance to DST (Daylight saving time) setting.

D. DST (DAYLIGHT SAVING TIME) SETTING

Note: The DST default is “On”, meaning that the WWVB will

automatically change the time according to Daylight Saving Time in the

spring and fall. For areas that do not recognize DST changes (Arizona

and parts of Indiana) turn the DST “OFF”.

1. Hold down the “SET” button for 1 second (the selected time zone will

flash); press the “SET” button once more until “On” flashes in the

lower left and “DST” flashes in the upper right.

2. Press and release the “Mode/+” button to turn the DST off, as will be

indicated by the display of “OFF” in the time LCD.

Note: Only turn the DST setting off if you live in an area that does not

change time for Daylight Saving Time.

3. Press and release the “SET” button to confirm the DST setting, and

to advance to select the length of the snooze.

E. ADJUSTABLE SNOOZE TIME

Note: The snooze length can be adjusted from 1 minute to 59 minutes.

This duration refers to the length of time the alarm will be disabled when

the “SNOOZE” bar is pressed. If set to “0”, activating the snooze will turn

off the alarm for 24 hours.

1. Hold down the “SET” button for 1 second (the selected time zone will

flash), press the “SET” button 2 more times, until “Sno” appears in

the lower left and duration (“:10” default) flashes in the time LCD.

2. Press and release the “Mode/+” button to advance the snooze time

from 0 (off) to 59 minutes.

-4h Atlantic Time

-5h Eastern Time (default setting)

-6h Central Time

-7h Mountain Time

-8h Pacific Time

-9h Alaskan Time

-10h Hawaiian Time

-11h, -12h Next two time zones West of HAW

0h Greenwich Mean Time

-1h, -2h, -3h Three time zones West of GMT

3. Press and release the “SET” button to confirm the snooze setting,

and to advance to manually set the time.

F. TIME SETTING

Note: When the WWVB signal is found, that time will over-ride the

manually set time.

1. Hold down the “SET” button for 1 second (the selected time zone will

flash), press the “SET” button 3 more times, until the hour flashes in

the time LCD.

2. Press and release the “Mode/+” button to select the hour. Note:

when setting the hour, “PM” will appear to the left of the hour display,

if it is AM nothing will be displayed.

3. Press and release the “SET” button to confirm the hour setting, and

to advance to select the minutes.

4. Press and release the “+” button to select the minutes.

5. Press and release the “SET” button to confirm the time setting, and

to advance to manually set the date.

G. DATE SETTING

Note: When the WWVB signal is found, that date will over-ride the

manually set date.

1. Hold down the “SET” button for 1 second (the selected time zone will

flash), press the “SET” button 5 more times, until the year flashes in

the date LCD.

2. Press and release the “Mode/+” button to select the year.

3. Press and release the “SET” button to confirm the year, and to

advance to set the month.

4. The month will flash. Press and release the “+” button to select the

appropriate month.

5. Press and release the “SET” button to confirm the month, and to

advance to set the date.

6. The date will flash. Press and release the “Mode/+” button to select

the appropriate date.

7. Press and release the “SET” button to confirm the date, and to

advance to set the weekday.

8. The weekday will flash. Press and release the “Mode/+” button to

select the appropriate weekday.

9. Press and release the “SET” button to confirm the calendar settings,

and to advance to select either 12 or 24-hour time display.

H. 12/24-HOUR SETTING

Note: Setting to the 24-hour mode (also known as Military Time) will also

change the temperature to display in

C instead of

1. Hold down the “SET” button for 1 second (the selected time zone will

flash), press the “SET” button 9 more times, until the “12” or “24”

hour time display flashes in the time LCD.

2. Press and release the “Mode/+” button to toggle between 12 and 24-

hour time.

3. Press and release the “SET” button to confirm the 12/24-hour time

display, and to return to normal operation.

III. FEATURES & OPERATIONS

A. FEATURES

1. Radio-controlled time and date

2. Projection of time and/or remote temperature

3. EL backlight

4. Six modes of date/seconds/temperature display

5. Indoor temperature

6. Remote outdoor temperature

7. Dual alarms

8. Adjustable snooze

9. Forecast icon based on changing air pressure

B. RADIO-CONTROLLED TIME AND DATE

1. The projection alarm will automatically search for the time signal

upon initial set-up and every night.

2. When the signal is being received, there will be a “tower” icon

flashing to the left of the time display.

3. When the time signal has been received successfully, the tower icon

will remain steady until midnight.

4. The NIST (National Institute of Standards and Technology—Time

and Frequency Division) WWVB radio station is located in Ft. Collins,

Colorado, and transmits the exact time signal continuously

throughout the United States at 60 kHz. The signal can be received

up to 2,000 miles away through the internal antenna in the Projection

alarm.

5. Due to the nature of the Earth’s Ionosphere, reception is very limited

during daylight hours. The Projection alarm will search for a signal

every night when reception is best.

6. The WWVB radio station receives the time data from the NIST

Atomic clock in Boulder, Colorado. A team of atomic physicists is

continually measuring every second, of every day, to an accuracy of

ten billionths of a second per day. These physicists have created an

international standard, measuring a second as 9,192,631,770

vibrations of a Cesium-133 atom in a vacuum.

7. For more detail, visit http://www.boulder.nist.gov/timefreq.htm. To

listen to the NIST time, call (303) 499-7111. This number will connect

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali La Crosse Technology Sveglia

La Crosse Technology

La Crosse Technology WS-8256U Manuale utente

La Crosse Technology

La Crosse Technology WS-8117U-IT Manuale utente

La Crosse Technology

La Crosse Technology K84292 Manuale utente

La Crosse Technology

La Crosse Technology 617-2410V2 Dimensioni

La Crosse Technology

La Crosse Technology Equity 20090 Manuale utente

La Crosse Technology

La Crosse Technology WT-5432 Manuale utente

La Crosse Technology

La Crosse Technology 616-1950 Dimensioni

La Crosse Technology

La Crosse Technology 616-1412v3 Manuale utente

La Crosse Technology

La Crosse Technology RADIO CONTROLLED PROJECTION ALARM CLOCK Manuale utente

La Crosse Technology

La Crosse Technology Soluna C79141 Dimensioni

La Crosse Technology

La Crosse Technology 616-146A Manuale utente

La Crosse Technology

La Crosse Technology Radio-Controlled Travel Alarm Clock WT-2160 Manuale utente

La Crosse Technology

La Crosse Technology K85236 Dimensioni

La Crosse Technology

La Crosse Technology 513-1417BS Dimensioni

La Crosse Technology

La Crosse Technology 616-1950V2 Manuale utente

La Crosse Technology

La Crosse Technology WT-5120 Manuale utente

La Crosse Technology

La Crosse Technology 616-1410 Manuale utente

La Crosse Technology

La Crosse Technology soluna W74146 Manuale utente

La Crosse Technology

La Crosse Technology Soluna C79141 Manuale utente

La Crosse Technology

La Crosse Technology W88723v2 Manuale utente

La Crosse Technology

La Crosse Technology 817-2410 Manuale utente

La Crosse Technology

La Crosse Technology 616A-1908 Dimensioni

La Crosse Technology

La Crosse Technology WT-5220U-IT Manuale utente

La Crosse Technology

La Crosse Technology 617-89577 Dimensioni

Manuali Sveglia popolari di altre marche

Steren

Steren CLK-210 Manuale utente

COP-USA

COP-USA ALCDVR32-SL Manuale utente

Philips

Philips HF3505/70 Manuale tecnico

Casio

Casio PQ-70 Manuale utente

iHome

iHome IA63 Manuale utente

Coopers

Coopers 9765 Manuale utente

ANJANK

ANJANK AC-190 Guida

TFA

TFA 98.1075 Manuale utente

Sharper Image

Sharper Image 204050 Manuale utente

Lumie

Lumie Zest Manuale utente

Dexford

Dexford RCT200 Manuale utente

Philips

Philips AJL303/37B Manuale utente

RST

RST Q754 Manuale utente

iHome

iHome iKT50 Manuale utente

Sony

Sony dash HID-B7 Manuale utente

SVINZ

SVINZ SCC009 Manuale utente

Clas Ohlson

Clas Ohlson 918863 Manuale utente

IKEA

IKEA FNURRA Manuale utente