La Crosse Technology WS-3510 Guida utente

TOUCH-SCREEN WEATHER STATION MODEL

WS-3510

QUICK OPERATION GUIDE

1 Shipping Contents

The shipping contents of the touch-screen weather station WS-

3510 include the touch-screen weather station, a remote

temperature/humidity sensor, the respective connecting cables,

an AC adapter and the PC software package on CD-ROM.

2 Connections

The use of the direct cable connection between the touch-screen

weather station and remote temperature/humidity sensor depends on

the chosen operating mode (see Item 3 Power Supply).

3 Power Supply

Depending on the type of data transmission from remote tempera-

ture/humidity sensor to touch-screen weather station, the units can be

supplied with power in the following possible combinations:

•

With cable connection or 433 MHz wireless transmission: touch-

screen weather station batteries, remote temperature/humidity

sensor batteries.

•

With 433 MHz wireless transmission: touch-screen weather station

AC adapter, remote temperature/humidity sensor batteries.

•

With cable connection: Both units supplied by AC adapter.

The last mentioned cable connection avoids battery wear-out and

allows data transmission less prone to interferences.

4 Putting into Operation

For transmission security, first the remote temperature/humidity sensor

and in immediate after the touch-screen weather station must be put

into operation by power being applied to it.

By doing this full scale operation of the total system of the touch-screen

weather station is ensured.

It is beneficial to tentatively put the system into operation in close

proximity (e. g. on a table) in order to ensure correct function in the

configuration it is intended to be used.

5 System Start

After inserting the batteries or respectively connecting the AC adapter

the LCD of the touch-screen weather station will for a few seconds

display all possible segments.

Immediately after this the unit will enter the check mode during which

for about 15 minutes all measured and received weather data are being

switched through, updated and displayed.

This phase allows the user of the touch-screen weather station to check

all cables for correct connection and all components for correct

function.

After completing the check mode – which can also be terminated

prematurely by once touching the TIME display in the upper left section

of the LCD – the touch-screen weather station will automatically switch

to the normal display mode from which all further setting can be

performed by the user.

Note:

•

Reception of the radio-controlled time information will only take

place after completion of the check mode (approx. 15 minutes).

This mode can however be discontinued and the time and date can

be set manually.

•

Prior to manual setting or reception of WWVB radio-controlled time

information there will be no recording of weather history data.

6 Placement

After the touch-screen weather station has been checked for correct

function with regard to the above points and found fit, the mounting of

the system components can take place. It must be ensured however

that all components work properly from their chosen mounting or

standing locations. If there appear to be problems with the 433 MHz

wireless transmission they can mostly be overcome by slightly moving

the mounting locations.

7 Setting Up

•

All settings of the touch-screen weather station are performed by

means of menu steps in the text section of the touch-screen

weather station (last two lines on the lower part of the LCD). This

menu for basic settings and basic displays is started by slightly

touching (not pressing!) the center of the text display during

normal display mode.

•

All further actions and functions of the touch-screen weather

station are started by touching the switching areas appearing in

star (٭) symbols (in the text section only) or the displayed values

on the touch screen respectively.

•

For a number of value displays touching the display twice will lead

to further displays or functions. All setting and display facilities only

pertain to the presently displayed value or function.

•

The setting of functions, values and units is in all modes performed

by use of the switching areas ٭ON٭or ٭OFF٭,٭UP٭or ٭DOWN٭

or by direct unit selection.

•

Advance to any next menu step with ٭NEXT٭, leave or terminate

all respective modes with ٭EXIT٭.

•

Every programming step activated by touching a switching area on

the touch screen is acknowledged by an audible signal (with

buzzer switched ON).

•

If during any process previously activated by use of the touch

screen no further action is activated for about 20 seconds, the

active process is automatically terminated and switched back to the

normal display mode (automatic time-out).

8 PC Connection

Note: Please read the Help file on your CD-ROM before connecting the

WS 3510 to your PC.

An important feature exceeding the mere display on the LCD, the

touch-screen weather station allows the read-out of all measured and

displayed time and weather data in the form of complete history data

sets on a PC.

The wiring between touch-screen weather station and PC takes place

by means of the included COM port cable. Furthermore the “Heavy

Weather Pro“ software package also included in the shipping contents

must be installed on the PC.

For further details to the subject “PC Connection“ please see the Help

File on the installation disk.

Note:

•

When first putting the touch-screen weather station into operation

the history memory will be empty (no data).

•

Data read-out by means of the PC is only possible after at least 3

data sets have been stored (15 minutes after setting of a valid

time). It is therefore recommended to connect the PC and start the

Heavy Weather Pro software only after this time period has

passed.

Important Note:

•

User is recommended to carefully read the main operation

manual for set up details. And further utilization of the PC

program refers to the "Help" file (opened by clicking the Ques-

tion mark button in menu bar) of the Heavy Weather program.

(The Wind and Rain measurements are not applicable to the

model WS-3510.)

TOUCH-SCREEN WEATHER STATION MODEL

WS-3512

Operation Manual

Table of Contents

1 ................. General

2 ..................Important Touch-screen Operating Notes

3 ................. Putting into Operation

3.1............ Wiring the System

3.2............ Power Supply

3.2.1 ...... Batteries

3.2.2 ...... AC Adapter

3.2.3 ...... Cable Connection

3.3............ System Start

3.4............ Placement

4 ................. Setting Up

5 ................. Display of stored Min/Max Values and Alarm Value Settings

6 ................. Radio Controlled WWVB Clock

7 ................. Weather Tendency

8 ................. Air Pressure History

9 ................. Operating and Setting of Various Functions

9.1............ Air Pressure

10 ............... Additional Information to Function Outdoor Temperature

11 ............... Operating and Setting the Backlight, Buzzer and Alarm

11.1.......... EL Backlight

11.2.......... Buzzer

11.3.......... Alarm

12 ............... PC Connection

12.1.......... Data Storage

12.2.......... Data Recall

12.3.......... Connections and Software

13 ............... Technical Data

13.1.......... Outdoor Data

13.2.......... Data Transmission by 433 MHz Signal

13.3.......... Data Transmission by Cable

13.4.......... Indoor Data

13.5.......... Power Supply

13.6.......... PC Connection

13.7.......... Dimensions

14 ............... Warranty Information

1 General

Important Note:

Before inserting batteries please carefully read the entire operation manual.

The shipping contents of the touch-screen weather station WS-3512 include the touch-screen weather station, a remote

temperature/humidity sensor, the respective connecting cables, an AC adapter and the PC software package on CD-

ROM.

The weather station is equipped with a touch-screen LCD monitor and allows, by use of comprehensive menu controls,

the display of a vast variety of time and weather data (from top to bottom):

•

Radio-controlled time (Time) (also referred to as Atomic Time)

•

Calendar (Date)

•

Wind speed, gust, and direction

•

Air pressure and air pressure history (Pressure, Pressure History)

An important feature of the touch-screen weather station is the ability, through the use of the supplied cable and

software, to supply all measured and displayed time and weather data to a PC and the ability to upload the data

to internet web sites.

2 Important Touch-Screen Operating Notes

All actions and functions of the touch-screen weather station are started on the touch-screen by slightly touching (not

pressing!) the switching areas appearing in star (٭) symbols (only in the text section at the bottom of the LCD) or the

displayed values respectively.

The setting of functions, values and units is in all modes performed by use of the switching areas ٭ON٭or ٭OFF٭, ٭UP٭

or ٭DOWN٭or by direct unit selection.

You can advance to the next respective menu step with the ٭NEXT٭area or leave all respective modes with ٭EXIT٭.

Every programming step activated by touching a switching area on the touch-screen is acknowledged by an audible signal

(with buzzer switched ON).

If during any process no further action is activated for about 30 seconds the active process is automatically terminated

and switched back to the normal display mode (automatic time out).

Touch-screen "switching area" on LCD:

Date section

Time section

3 Putting into Operation

It first must be decided whether battery or AC (using the included adaptor) power will be used to operate the system. Both

methods allow the connection of remote temperature/humidity sensor and touch-screen weather station by cable or 433

MHz wireless signal.

Note: When putting the wireless weather station into operation it is important to first perform a complete wiring and setup

of the system in the configuration you intend to use. This serves as a test of all components for correct function before

placing and mounting them in their final destinations.

3.1 Wiring the System

The direct cable connection of remote temperature/humidity sensor and touch-screen weather station can be used when:

PC/COM port

receptacle

AC adapter receptacle

Remote Thermo/hygro

sensor receptacle

-The flexibility of 433 MHz wireless transmission is not needed.

-Data transmission absolutely free of any environmental interference is wanted.

3.2 Power Supply

Power to the touch-screen weather station can be supplied by batteries or the included AC adapter.

3.2.1 Batteries:

•

First insert two AA 1.5 V batteries into the battery compartment of the remote temperature/humidity sensor.

•

Immediately following this insert three AA 1.5V batteries into the battery compartment of the touch-screen weather

station.

Please help in the preservation of the environment and return used batteries to an authorized depot.

3.2.2 AC Adapter:

•

First insert two AA 1.5 V batteries into the battery compartment of the remote temperature/humidity sensor.

•

Immediately following this connect the AC adapter to the touch-screen weather station and then plug it into a power

outlet.

Note: In both cases it is important to observe this order of succession since the remote temperature/humidity sensor will

send an identification code which has to be received and stored by the touch-screen weather station within the first few

minutes of operation.

3.2.3 Cable Connection:

One further feature of the direct cable connection mentioned in Item 3.1 above is that in case of AC adapter operation

power is provided not only to the touch-screen weather station but to the remote temperature/humidity sensor as well.

Note: Operating the system configured with a wired connection between the remote temperature/humidity sensor and

touch-screen weather station and power supplied by only batteries in the touch-screen weather station is not

recommended. The system will operate however there will be considerably shorter battery life due to the high power

requirements. The batteries may however remain in the unit for emergency supply in case of a power failure.

A change from cable operation to 433 MHz wireless transmission or vice versa is possible since the touch-screen weather

station will recognize this change and will automatically switch to the appropriate operating mode.

3.3 System Start

After powering up both the remote temperature/humidity sensor and touch-screen weather station the LCD of the touch-

screen weather station will for a few seconds display all possible segments (to ensure all parts of the display can be

seen).

Immediately after this the unit will enter the check mode phase in which for about 15 minutes all measured and received

weather data be cycled through, updated and displayed. During this time period there will be no reception of the WWVB

time information.

Note: The check mode phase allows the user of the touch-screen weather station to check all cables for correct

connection and all components for correct function.

After completing the check mode the touch-screen weather station will automatically switch to the normal display mode

from which all further settings can be performed by the user. At this point of time the unit will also automatically start

reception of the WWVB time information.

Important Note:

Reception of the radio-controlled time information will only take place after completion of the check mode

(approx. 15 minutes). In case the user wants to start the system without waiting for completion of the check

mode it can be terminated prematurely by once touching the TIME display in the upper left corner of the LCD.

Prior to manual setting or reception of radio-controlled time information there will be no recording of weather

history data.

3.4 Placement

After the touch-screen weather station has been checked for correct function mounting the system components can take

place. It must be ensured however that all components work properly together at their chosen mounting or standing

locations. If there appear to be problems with the 433 MHz wireless transmission they can mostly be overcome by slightly

moving the mounting locations.

Note: Commonly the wireless communication between the remote temperature/humidity sensor and touch-screen

weather station in the open field reaches distances of a maximum 330 feet (100 meters) providing that there are no

interfering obstacles such as buildings, trees, vehicles, high voltage lines, etc.

Radio interferences created by PC screens, radios or TV sets can in some cases entirely cut off wireless communication.

Please take this into consideration when choosing standing or mounting locations.

4 Setting Up:

Note: Because the default settings already determined by the manufacturer it may not be necessary for many users to

perform - outside possibly the Relative Air Pressure (see further down) - any further basic settings. Changes however can

easily be made if desired.

For basic settings the following menu is started by touching the touch-screen in the center of the text display (last two

lines on the LCD). Touching the display ٭SETUP٭will enter the setup mode.

The basic settings can now be performed in the following successive order:

LCD Contrast →Contrast can be set in 8 steps from 0 to 7 (Default 4).

Time Zone →Time Zones can be set in the range from -12 to +12 hours (Default -5 hours for Eastern).

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali La Crosse Technology Stazione meteorologica

La Crosse Technology

La Crosse Technology WS-7213U Manuale utente

La Crosse Technology

La Crosse Technology WS-8610 Manuale utente

La Crosse Technology

La Crosse Technology WS-7168U Manuale utente

La Crosse Technology

La Crosse Technology WS-7038U Manuale utente

La Crosse Technology

La Crosse Technology 308-1414M Manuale utente

La Crosse Technology

La Crosse Technology C80758 Manuale utente

La Crosse Technology

La Crosse Technology TX231TH Manuale utente

La Crosse Technology

La Crosse Technology Wireless Weather Station Manuale utente

La Crosse Technology

La Crosse Technology WS-2816U-IT Manuale utente

La Crosse Technology

La Crosse Technology Bonus Station Manuale utente

La Crosse Technology

La Crosse Technology 308-1417BLV2 Manuale utente

La Crosse Technology

La Crosse Technology WS-3500 Manuale utente

La Crosse Technology

La Crosse Technology WS-9047UIT-CA Manuale utente

La Crosse Technology

La Crosse Technology V22-WRTHV2 Manuale utente

La Crosse Technology

La Crosse Technology 328-1415 Guida all'installazione

La Crosse Technology

La Crosse Technology WS-7390U Manuale utente

La Crosse Technology

La Crosse Technology 308-146W Manuale utente

La Crosse Technology

La Crosse Technology T83646v2 Dimensioni

La Crosse Technology

La Crosse Technology WS-1516-IT Guida all'installazione

La Crosse Technology

La Crosse Technology 308-1425BV3 Manuale utente

La Crosse Technology

La Crosse Technology 724-1710v2 Manuale operativo e di manutenzione

La Crosse Technology

La Crosse Technology C85845 Manuale utente

La Crosse Technology

La Crosse Technology 308-1415FCT Dimensioni

La Crosse Technology

La Crosse Technology WS-9031U Manuale utente

Manuali Stazione meteorologica popolari di altre marche

Auriol

Auriol AHFL 433 A1 Manuale utente

NexSens

NexSens G2-HYDROMET Manuale utente

Hyundai

Hyundai WS 2202 Manuale utente

IROX

IROX HBVR761 UV-X Manuale utente

ADE

ADE WS 1711 Manuale utente

Auriol

Auriol z29592 Manuale utente

Auriol

Auriol 296289 Manuale utente

Hyundai

Hyundai WS 2266 Manuale utente

Ventus

Ventus W177 Manuale utente

National Geographic

National Geographic VA Colour RC Manuale utente

Renkforce

Renkforce 1208067 Manuale utente

Levenhuk

Levenhuk Discovery Report WA40 Manuale utente

Instant Transmission

Instant Transmission MA 10410 Manuale utente

Lutron Electronics

Lutron Electronics PHB-318 Manuale utente

WAREMA

WAREMA EWFS Weather station eco Manuale utente

TFA

TFA 30.3013.IT Manuale utente

Alecto

Alecto WS-1200 Manuale utente

Oregon Scientific

Oregon Scientific RMR966PA Manuale utente