Labo K Effects Warm Lady Manuale utente

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
2
Contents
CONTENTS 2
TECHNICAL INFO 3
OVERVIEW 4
CONTROLS 5
POWER SUPPLY 6
POWER-LINK SYSTEM 7
ADVICES 9
TROUBLESHOOTING 10
RECALL SHEET 11

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
3
technical info
COntrols
!Output level (Volume)
!Tone (Tone)
!Distortion amount (Drive)
TECHNOLOGy
!Selected components
!Robust diecast enclosure
!Cliff et Lumberg connectors
specifications
!True Bypass 3PDT switch.
!Consumption 4mA.
!Power: 9V battery or AC adapter DC 9V (not included).
!Dimensions : 4.7 (W) x 3.7 (D) x 1.6 (H)
!Weight: 13.05 Once.
Use quality mono Jacks cords only.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
4
overview
Warm Lady is to be classified in the family of Boosters / distortions.
She allows to obtain the sound of lamps overheated by an amplier.
The tuning of tonality is effective. Inserted into the chaine of the pedals of
effects her can also act as booster by respecting the grain of the guitar.
The Warm Lady will give body to your sound even at low level.
Like all Labo ★K Effects pedals, the Warm Lady is True By Pass. It means
that when the effect is not active, the device is completely disconnected from the
path of the signal and thus adds none résistive load in this one (The accumulation
of résistives loads on the path of the signal eventually decreases the power and the
brightness of the sound)
Optionals accessories
Power-Link cord by Labo ★K Effects
Allows to chain the supply of several
pedals from a single power supply using
the specific cord. (supplied with each
Warm Lady)
Knobs for Labo ★K Effects pedals.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
5
controls
I – THE POTENTIOMETERS
1. Volume
This control adjusts the output level of the Warm Lady.
2. Tone
The tone control acts on the frequency range of the signal.
3. Drive
This setting controls the amount of distortion.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
6
Power supply
Labo ★K Effects pedals are powered by 9V DC battery or external power
adapter using the « Boss ™ » standard (negative (-) in the center,
positive (+) outside.
The pedal can be supplied in several ways:
!9V internal battery.
!AC Power adapter.
!AC Power adapter from another Labo ★K Effects via « Power-Link »
cord.
!9V battery from another Labo ★K Effects pedal via « Power-Link »
cord.
Notes :
The power consumption of the Warm Lady is 4mA what gives internal
battery a comfortable lifetime.
When the input jack is not pressed, the internal battery is disconnected.
Change of the internal battery is done by unscrewing the four screws on
the bottom of the box.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
7
power-link system
The Power-Link system of Labo ★K Effects allows an external power
supply to power several Labo ★K Effects pedals via the cable supplied
with each pedal by creating a daisy chain.
Using the Power-Link system of Labo ★K Effects it is even possible to
power a Labo ★K Effects pedal (or any other pedal using tne same
power standard) with the internal battery of a Labo ★K Effects pedal.
The amperage of the power supply used must be higher than the total
consumption of pedals you want to feed simultaneously.
To respect the sense of connection, the Power-Link system uses 2
different connectors.
Lumberg connector J21 for the input.
Lumberg connector J25 for the output.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
8
USE OF THE POWER-LINK CORD

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
9
advices
To keep the integrity of the sound, use good quality mono Jack cords
exclusively.
To extend the life of the battery, remove the connector of the input jack
when not using the device.
Replace the battery when the light shines only weakly or not at all during
the use.
If an external adapter is exclusively used, it is recommended to remove
the internal battery
Use as Booster:
The Warm Lady can be used as a booster after the Fuzz Ultra for example.

Labo ★K Effects – www.labo-k-effects.com – contact@labo-k-effects.com
10
troubleshooting
STAGE 1
No sound comes out of the device:
!Verify that all your equipment works without the pedal.
!Insert the pedal into the chain.
!If the sound takes out in by pass mode, go directly in the stage 2.
If the sound does not comes out either in by pass mode, nor in effect
mode, go directly to the stage 4
STAGE 2
No audio ouput when the device is switched on :
!Verify that the output volume is not in zero position.
!· If the light shines correctly go to the stage 4.
STAGE 3
If the light shines weakly or not at all and the sound is weak and very
distorted:
!Change the battery or verify the connection of the power cable.
STAGE 4
Your device is broken:
!Contact Labo ★K Effects by mail
Indice
Altri manuali Labo K Effects Pedale effetti



