Laguna Tools PRO SERIES Manuale utente
THRIVING ON INNOVATION
Pro Series 4, 6 & 9 Panelsaw Manual
17101 Murphy Avenue, Irvine, CA 92614 www.lagunatools.com 800.234.1976
2
Dear Woodworker:
Thank you for your purchase and welcome to the Laguna Tools group of
discriminating woodworkers. I understand that you have a choice of
where to purchase your machines and appreciate the confidence you
have in our products.
Every machine sold by Laguna Tools has been carefully designed and
well thought through from a woodworker’s perspective. I cut on our
bandsaws, lathes, table saws and combination machines. Through my
hands-on experience, I work hard to make our machines better. I
strive to give you machines that inspire you to create works of art.
Machines that are a joy to run and work on. Machines that encourage
your performance.
Today, we offer high-performance machines with innovative solutions
that meet the needs of woodworkers and their ever-evolving craft.
I started Laguna Tools as a woodworker; I still am.
Thank you again for becoming a Laguna Tools customer.
Torben Helshoj
President and Founder - Laguna Tools
Thriving on Innovation
3
Table of contents
Page number
Safety Rules 4
Limited warranty 5
Noise emission 6
Specification sheet 7
Receiving your machine 8
Introduction to Table Saws 8
Parts of the Table Saw 9
Where to locate your machine 11
Unpacking your machine 11
Assembly and setup 14
Using and adjusting the machine 31
Maintenance and troubleshooting 34
Electrical drawing 43
Exploded view drawings and parts lists 46
4
Safety Rules
As with all machinery there are certain hazards involved with the
operation and use. Using it with caution will considerably lessen the
possibility of personal injury. However, if normal safety precautions are
overlooked or ignored, personal injury to the operator may result. If you
have any questions relative to the installation and operation, do not use the
equipment until you have contacted your supplying distributor.
Read the following carefully before operating the machine:
1. Keep the working area clean and be sure adequate lighting is
available.
2. Do not wear loose clothing, gloves, bracelets, necklaces or
ornaments. Wear face, eye, respiratory and body protection devices
as indicated for the operation or environment.
3. Be sure that the power is disconnected from the machine before tools
are serviced or an attachment is to be fitted or removed.
4. Never leave the machine with the power on.
5. Do not use dull, gummy or cracked cutting tools.
6. Be sure that the keys and adjusting wrenches have been removed
and all the nuts and bolts are secured.
5
Limited Warranty
New woodworking machines sold by Laguna Tools carry a one-year warranty
from the date of shipping. Laguna Tools guarantees all new machines sold to be
free of manufacturers’ defective workmanship, parts, and materials.
We will repair or replace, without charge, any parts determined by Laguna
Tools, Inc. to be a manufacturer's defect. We require the defective item/part to
be returned to Laguna Tools. In the event the item/part is determined to be
damaged due to lack of maintenance, cleaning or misuse/abuse, the customer
will be responsible for the cost to replace the item/part, plus all related shipping
charges.
This limited warranty does not apply to natural disasters, acts of
terrorism, normal wear and tear, product failure due to lack of maintenance or
cleaning, damage caused by accident, neglect, lack of or inadequate dust
collection, or misuse/abuse or damage caused when repair or alterations have
been made or attempted by others.
Laguna Tools, Inc. is not responsible for additional tools or modifications sold
or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools,
Inc. woodworking machine. Warranty may be voided upon the addition of such
noted tools and/or modifications, determined on a case-by-case basis.
Normal user alignment, adjustment, tuning and machine settings are not
covered by this warranty. It is the responsibility of the user to understand
basic woodworking machinery settings and procedures and to properly
maintain the equipment in accordance with the standards provided by the
manufacturer.
Parts, under warranty, are shipped at Laguna Tools, Inc's cost either by
common carrier, FedEx Ground service or a similar method.
Technical support to install replacement parts is primarily provided by phone,
fax, or e-mail. The labor required to install replacement parts is the
responsibility of the user.
Laguna Tools is not responsible for damage or loss caused by a freight
company or other circumstances not in our control.
Only new machines sold to the original owner are covered by this warranty.
For warranty repair information, call 1-800-332-4094.
6
Noise emission.
Notes concerning noise emission:
Given that there exists a relationship between noise level and exposure times, it
is not precise enough to determine the need for supplementary precautions. The
factors affecting the true level of exposure to operators are clearly the amount
of time exposed, the characteristics of the working environment, other sources
of dust and noise, etc. For example, adjacent machines, in other words, the level
of ambient noise. It is possible that exposure level limits will vary from country
to country.
Note:- When using a scoring blade, the
machine will only accept a 10” main blade
7
Specification sheet.
Note:- The first part of this manual covers the Pro Sliding
Tablesaw [4 foot]. The Pro Series 6ft & 9ft Sliding are covered at
the end of the manual.
Machine Sliding table saw 6’ sliding panel
saw 9’ sliding panel
saw
Blade 10” or 12” 10” or 12” 10” or 12”
Dado capacity 13/16” 13/16” 13/16”
Main motor 3 hp220V single
phase 4hp220V single
phase 4hp220V single
phase
Electrical cable Yes Yes Yes
Cast-iron [ground]
table size 32” X 20” 32” X 20” 32” X 20”
Table height 34” 34” 34”
Weight Shipping/
Net 1250 / 1100lb 1350 / 1200 lb 1600 / 1400 lb
Dust port 4” 4” 4”
Blade guard Yes Yes Yes
Scoring blade
diameter 120mm X 22mm 120mm X 22mm 120mm X 22mm
Scoring motor ¾ hp ¾ hp ¾ hp
Main blade speed 4500 rpm 4500 rpm 4500 rpm
Scoring blade speed 6500 rpm 6500 rpm 6500 rpm
Rip capacity 50” 50” 50”
Sliding table
dimensions 47” X 14” 63” X 14” 106” X 142
Cross-cut capacity 51” 73” 116”
Cutting height 90/45
deg with scoring 3 ½” / 2 1/8” 3 ½” / 2 1/8” 3 ½” / 2 1/8”
Cutting height 90/45
deg. with out scoring 4” / 2 ¾” 4” / 2 ¾” 4” / 2 ¾”
8
3
7
10
4
9
6
8
5
1
11
12
13
14
Receiving your machine.
Note: It is probable that your machine will be delivered by a third party. Before
you unpack your new machine, you will need to first inspect the packing,
invoice and shipping documents supplied by the driver.
Insure that there is no visible damage to the packing or the machine. You need
to do this prior to the driver leaving. All damage must be noted on the delivery
documents and signed by you and the delivery driver. You must then contact
the seller [Laguna Tools] within 24.
Introduction to Table Saws.
This Table Saw is designed to give you years of safe service. Read this owner’s
manual in its entirety before assembly or use.
9
Parts of the Table Saw.
The major parts are discussed in this manual. If you are not familiar with the
table saw take the time to read this section and become familiar with the
machine.
1. Body.
2. Dust collection port.
3. Angle adjustment handle.
4. Table.
5. Guard.
6. Fence.
7. Extension table.
8. Emergency stop button.
9. Blade height adjustment handle.
10. Electrical box and on/off switches.
11. Clamp.
12. Support table.
13. Sliding table.
14. Miter fence.
Identification.
There is a plate at the back of the machine listing all the manufacturing data
including the serial number, model, etc.
Cabinet / Body.
The cabinet has a large footprint and is of welded construction manufactured
from heavy gauge steel plate. The cabinet houses all the parts of the machine
and the heavy construction ensures that the saw is stable. This weight also helps
to absorb any vibration that is produced during cutting.
Table.
The table is manufactured from cast iron. The table is attached to the cabinet.
The table is adjustable for being level and vertical.
Extension table.
An extension table is provided to increase the range of jobs that can be
produced.
Altri manuali per PRO SERIES
1
Indice
Altri manuali Laguna Tools Utensili elettrici
Laguna Tools
Laguna Tools PP16 XC Pro Manuale utente
Laguna Tools
Laguna Tools SHEARTEC II Manuale utente
Laguna Tools
Laguna Tools Dake Force 150 Manuale utente
Laguna Tools
Laguna Tools MJOPL104200 Manuale utente
Laguna Tools
Laguna Tools Dake SB-32V Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools PP16 XC Pro Manuale utente
Laguna Tools
Laguna Tools DAKE 0 Manuale utente
Laguna Tools
Laguna Tools DAKE Force 50DA Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools MJO6405-0800 Manuale utente
Laguna Tools
Laguna Tools MJOIN 8012-0130 Manuale utente
Laguna Tools
Laguna Tools DAKE Force 10DA Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools DAKE 1-1/2 Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools Platinum Series Manuale utente
Laguna Tools
Laguna Tools DAKE Y Manuale utente
Laguna Tools
Laguna Tools DAKE 3 Manuale utente
Laguna Tools
Laguna Tools Dake 972200 Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools DAKE 1 Manuale utente
Laguna Tools
Laguna Tools DAKE 150H Manuale utente
Laguna Tools
Laguna Tools DAKE 1-1/2C Manuale operativo e di manutenzione
Laguna Tools
Laguna Tools Platinum Series Manuale utente
