Laney CUB8 Manuale utente
CUB-8
https://projects.headstockgroup.com/#files/4463141
8
CUB-8
2
INTRODUCTION
The CUB-8 is a straight forward easy to use all tube combo amplifier housed in a stylish ‘boutique ‘ cabinet.
Its 5W Single Ended Class A output stage oozes classic tube tones through a Premium 8" speaker.
The black front panel features vintage simplicity. Flick ON the chrome toggle switch, set the tone and volume controls and you
are ready to Rock.
The cabinet is finished in two tone black leather grain vinyl and includes a comfortable soft grip handle for easy transportation.
Moving round to the rear panel, the Cub gets its claws out with an extension cabinet socket, to which any of the cabinets in the
Laney range could be connected. The internal loudspeaker and valves are protected by the rugged rear grille.
We hope you get a kick out of using your CUB-8, we certainly did designing and making it.
Best wishes from all at Laney.
CUB-8
3
FEATURES
Experiment with both inputs to find your best sound. To avoid poor sound only use good quality guitar cables.
5 – LO INPUT – ‘LO’ stands for low gain. This input is attenuated down approximately 50% from the ‘HI’ input and is
designed for full range clean sounds
4 – VOLUME – Sets how loud the amplifier is. Try cranking it up a little to drive the power tube harder for that real retro
sound and feel, that only a quality tube amplifier can deliver. Now use your guitar volume to control the amount of distortion.
6 – HI INPUT – ‘HI’ stands for high gain. This input is designed to enable the amplifier to be overdriven more easily and
has a restricted low frequency range to avoid a “mushy” sound from high output guitars.
2 – POWER INDICATOR – This lamp will illuminate once the amplifier is switched on.
3 – TONE – The tone control works in a similar fashion to the Tone control you probably have on your guitar except that it
uniquely works at the other end of the amplification chain. This has the ability to not only control the overall top end response,
but also reduce upper end harmonics on the output stage and preamplifier overdrive sounds. This will give you bright cutting
sounds at high settings and smooth rounded sounds at lower settings. (Midway (5) is a good starting point).
1 – POWER SWITCh – Main power switch for the unit. Tube amplifiers take between 30 seconds and 2 minutes to
warm up and be ready to play after switching on, this is normal.
123456
LO HI
VOLUME
POWER
TONE
INPUT
CUB-8
4
FEATURES CONTINUED
EXTERNAL SPEAKER
IMPEDANCE
8-16 OHMS
CAUTION - RISK OF ELECTRIC SHOCK DO NOT OPEN
ATTENTION - LE RISQUE DE DÉCHARGE ÉLECTRIQUE NE S'OUVRENT PAS
SUPPLY VOLTAGE
50 WATTS 50/60Hz
MAXIMUM POWER CONSUMPTION
~120V
~220V
~230V
~240V
T500mA L 250V
~100V
T250mA L 250V
7
89 10 11
MODEL: CUB-8
SN: ABC1234567890
DESIGNED & ENGINEERED IN THE UK
BY LANEY ELECTRONICS LTD
11 – MAINS FUSE TRAY – This drawer contains the main safety fuse for the unit. The fuse protects the amplifier from
damage in the event of fault by disconnecting the mains power supply. USE ONLY THE CORRECT SIZE AND RATING
SPECIFIED ON THE PANEL. If a fuse blows or fails and a replacement of the same size and rating is installed which in turn
blows, the amplifier has suffered a malfunction and needs immediate service from a qualified technician. DO NOT TRY A
FUSE OF HIGHER RATING - Using a fuse that is too large in current rating may cause serious, irreparable damage to the
amplifier and presents a serious fire hazard. The mains fuse ratings are detailed in the Specifications section of this manual,
as well as printed on the rear of the amplifier. There is a spare fuse located in the fuse drawer of the mains power inlet in the
event of a failure.
10 – POWER SOCKET – Connected the supplied IEC power cord here.
9 – SERIAL NO – Displays the model details and serial number of the unit.
8 – EXTENSION CABINET – Using a good quality speaker cable, connect an external cabinet (8-16 Ohm) here.
Recommended suggestions include the CUB-112 and CUB-212 cabinets. If an alternative is used, please note a mismatched
impedance will reduce the amplifiers performance and in some cases may cause damage to your amplifier. When an external
loudspeaker is connected, the Onboard loudspeaker will be muted.
7 – SAFETY WARNINGS – Please adhere to the warnings for your safety and the prolonged operation of the Cub-8
amplifier.
Always switch off and disconnect the power cord when not in use.
CUB-8
5
Technical Specifications
In the interest of continued product develo ment, aney rp L eserve the right to amend product specification without prior notice.
Packed Weight (Kg): 7.5
EAN: 5060109457391
(8 - 16 Ohm Impedance)
1xECC83/12AX7 Preamp tube
Hi and Lo Gain Inputs
Size (H*W*D) (mm): 303*304*197
Unit Weight (Kg): 6.5
Mains Fuse: (~220V>240V = T250mA L 250V) (~100>120V = T500mA L 250V)
1x6V6GT Power Tube
Tone and Volume Controls
(Operating voltage Factory set)
Loudspeaker output: Extension speaker socket
Input Impedance: 1MOhm
Loudspeaker (Internal): Premium HH 8" Driver - 8 Ohm
Output Power Rating: 5W
Features: Power Switch
Pure Single Ended Class A Valve tone
Power Consumption: 50W
Model: CUB-8
Type: Tube
Description: Vintage single-ended Class A design,
generating 5 watts RMS of tube tone.
Nominal Supply Voltage: ~100V, ~115V, ~220V, ~230V, 50/60Hz
INTERNAL
LOUDSPEAKER
HI INPUT
EXT. LOUDSPEAKER
8-16 OHMS
LO INPUT
PAD
V1a V1b V2
TONE
TONE
CONTROL
VOLUME
VOLUME
CONTROL
BLOCK DIAGRAM
CUB-8
In order to take full advantage of your new product and enjoy long and trouble-free performance, please read this owner's manual carefully, and keep it in a
safe place for future reference.
3) Cables: Never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could
cause damage to your complete system.
4) Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
1) Unpacking: LaneyOn unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the factory to
your dealer. In the unlikely event that there has been damage, please re-pack your unit in its original carton and consult your dealer. We strongly advise you
to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification
securely packed.
2) Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. With all system parts
connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc, BEFORE turning on your amplifier. Many products have large
transient surges at turn on and off which can cause damage to your speakers.
By turning on your amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loud bass
speakers. Wait till all system parts have stabilised, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on
your amplifier and then turn off its power before turning off other equipment.bass
CAUTION:
PRECAUCION:
ATTENTION:
VORSICHT:
WARNING:
ADVERTENCIA:
ADVERTISSEMENT:
ACHTUNG:
Intended to alert the user to the presence of uninsulated ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical
shock to persons.
Ce symbole est utililise pur indiquer a l’utilisateur de ce produit de tension non-isolee dangereuse pouvant etre d’intensite suffisante pour constituer un risque de choc
electrique.
Este simbolo tiene el proposito de alertar al usuario de la presencia de ‘(voltaje) peligroso’ que no tiene aislamiento dentro de la caja del producto que puede tener una
magnitud suficiente como para constituir riesgo de corrientazo.
To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified personnel.
Riesgo de corrientazo - no abra
Dieses Symbol soll den Anwender vor unsolierten gefahrlichen Spannungen innerhalb des Gehauses warnen, die von Ausrichender Starke sind, um einen elektrischen
Schlag verursachen zu konnen.
Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
Risk of electrical shock - DO NOT OPEN.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.
Dieses Symbol soll den Anwender vor unsolierten gefahrlichen Spannungen innerhalb des Gehauses warnen, die von Ausrichender Starke sind, um einen elektrischen
Schlag verursachen zu konnen.
Este simbolo tiene el proposito de la alertar al usario de la presencis de instrucccones importantes sobre la operacion y mantenimiento en la literatura que viene conel
producto.
Afin de reduire le risque de choc electrique, ne pas enlever le couvercle. II ne se trouve a l’interieur aucune piece pouvant etre reparee par l’utilisateur. Confier
l’entretien a un personnel qualifie.
Risques de choc electrique - NE PAS OUVIRIR
Para evitar corrientazos o peligro de incendio, no deja expuesto a la lluvia o humedad este aparato Antes de usar este aparato, lea mas advertcias en la guia de
operacion.
Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine Teile darin, die vom Anwender repariert werden Konnten.
Reparaturen nur von qualifiziertem Fachpersonal durchfuhren lassen.
Um einen elektrischen Schalg oder Feuergefahr zu vermeiden, sollte dieses Gerat nicht dem Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt
die Bedienungsanleitung lesen.
Afin de prevenir les risques de decharge electrique ou de feu, n’exposez pas cet appareil a la pluie ou a l’humidite. Avant d’utiliser cet appareil, lisez les advertissments
supplentaires situes dans le guide.
Risiko - Elektrischer Schlag! Nicht offen!
Para disminuir el risego de carrientazo, no abra la cubierta. No hay piezas adentro que el pueda reparar. Deje todo mantenimiento a los tecnicos calificadod.
To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this appliance please read the operating instructions for further
warnings.
IMPORTANT SAFETY INSTRUCTIONS
GENERAL INSTRUCTIONS
EN
6
CUB-8
FCC COMPLIANCY STATEMENT
2009/125/EU
Hereby, Laney Electronics Ltd. declares that the radio equipment is in compliance with Directives 2014/53/EU, 2011/65/EU,
---------------------------------------------------------------------------------------------------------------------------------------------------------
support.laney.co.uk/approvals
Full text of the EU declaration of conformity is available at the following internet address:
---------------------------------------------------------------------------------------------------------------------------------------------------------
1) This device may not cause harmful interference
Increase the separation between the equipment and receiver.
This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions:
Warning: Changes or modification to the equipment not approved by Laney can void the user's authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one or more of the following measures.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark (93/68/EEC), Low Voltage (2014/35/EU), EMC (2014/30/EU),
RoHS (2011/65/EU), ErP (2009/125/EU).
This product conforms to the requirements of the following European Regulations, Directives & Rules:
Reorient or relocate the receiving antenna.
----------------------------------------------------------------------------------------------------------------------------------------------------
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household
waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE (Waste Electrical
and Electronic Equipment) directive applicable in your country.
----------------------------------------------------------------------------------------------------------------------------------------------------
SIMPLIFIED EU DECLARATION OF CONFORMITY
2) This device must accept any interference received, that may cause undesired operation.
EN
7
CUB-8
CAUTION:
WARNING:
1. Read these instructions.
WARNING: When using electrical products, basic cautions should always be followed, including the following:
2. Keep these instructions safe.
3. Heed all warnings.
To prevent electrical shock or fire hazard, do not expose this appliance to rain
or moisture. Before using this appliance please read the operating
instructions.
5. Do not use this apparatus near water.
20. Symbols & nomenclature used on the product and in the product manuals, intended to alert the operator to areas where extra caution may be necessary, are as
follows:
If your appliance features a tilting mechanism or a kickback style cabinet,
please use this design feature with caution. Due to the ease with which the
amplifier can be moved between straight and tilted back positions, only
use the amplifier on a level, stable surface. DO NOT operate the amplifier
on a desk, table, shelf or otherwise unsuitable non-stable platform.
a) The wire that is coloured green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚ coloured green or
13. The mains plug or appliance coupler is used as the disconnect device and shall remain readily operable. The user should allow easy access to any mains plug,
mains coupler and mains switch used in conjunction with this unit thus making it readily operable. Unplug this apparatus during lightning storms or when unused
for long periods of time.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
b) The wire that is coloured blue must be connected to the terminal that is marked with the letter N or the colour black.
18.This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects
containing liquids, such as vases, upon the apparatus.
4. Follow all instructions.
16. If this product is to be mounted in an equipment rack, rear support should be provided.
Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
11. Only use attachments/accessories provided by the manufacturer.
15. Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
coloured green and yellow.
9. An apparatus with Class I construction shall be connected to a mains socket outlet with a protective connection. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
c) The wire that is coloured brown must be connected to the terminal that is marked with the letter L or the colour red.
7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
17. Note for UK only: If the colours of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚ proceed as follows:
The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible
noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some
hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification
system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure
against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to
equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
Risk of electrical shock - DO NOT OPEN. To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer
servicing to qualified personnel.
19. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in
susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense
noise for a sufficient time.
6. Clean only with a dry cloth.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.
Intended to alert the user to the presence of high ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of
electrical shock to persons.
EN
1 ½
2
1
8
Duration Per
Day in Hours
3
½
¼ or less
6
4
92
95
90
105
115
slow response
102
110
97
100
Sound Level dBA,
IMPORTANT SAFETY INSTRUCTIONS
8
CUB-8
TRANSLATION
DOCUMENTS
9
CUB-8 ES
123456
LO HI
VOLUME
POWER
TONE
INPUT
Experimente con las dos entradas para encontrar tu mejor sonido. Apenas use cables de alta calidad para evitar sonidos malos
o sin calidad.
2 – Indicador POWER – Esta lampara se ilumina cuando el amplificador es prendido.
4 – Control VOLUME – Ajusta el volumen del amplificador. Trate de aumentar un poquito para hacer con que la válvula
sea rempujada más fuerte y obtener aquel sonido tradicional retro, que solamente un amplificador con alta calidad puede
ofrecer. Ahora, con el control de volumen de su guitarra puedes controlar la cantidad de distorsión.
3 – Control TONe – El control de tono funciona de forma similar al control de tono de tu guitarra, con la diferencia de que
funciona solamente en la otra punta de la cadena de amplificación. Esto permite, no solo controlar la respuesta de la punta de
frecuencias altas, pero también reducir los armónicos de las frecuencias altas en la fase de salida de los sonidos
distorsionados en el preamplificador. Esto te brinda con sonidos cortantes en ajustes de alto volumen y sonidos suaves y
redondos en volúmenes menores. (El ajuste al medio (5) es un buen punto de partida).
5 – Conector LO INPUT – ‘LO’ significa baja ganancia. Esta entrada es atenuada en casi 50% de la señal en la entrada
‘HI’ input y se encuentra diseñada para sonidos limpios de rango completo.
1 – Llave POWER – Llave prende y apaga de la unidad. Después de prender, los amplificadores a válvulas tardan entre 30
segundos a 2 minutos para calentar y estar listo para el uso, esto es normal.
6 – Conector HI INPUT – ‘HI’ significa alta ganancia. Esta entrada permite que el amplificador sea distorsionado más
fácilmente y tiene un rango restricto de frecuencias bajas para evitar un sonido “embarajado” desde guitarras con salida alta.
10
PANEL DE CONTROL
Altri manuali per CUB8
2
Indice
Altri manuali Laney Amplificatore
Laney
Laney CUB10 Manuale utente
Laney
Laney B1 Manuale utente
Laney
Laney MBH165 Manuale utente
Laney
Laney mini-iron Manuale utente
Laney
Laney GS212IE Manuale utente
Laney
Laney Tube Fusion Manuale utente
Laney
Laney CA Series Manuale utente
Laney
Laney LA20C Manuale utente
Laney
Laney Alliance VC50 Manuale utente
Laney
Laney Concept CD480M Manuale utente
Laney
Laney F67-LIONHEART Manuale utente
Laney
Laney CA Series Manuale utente
Laney
Laney LX12 Manuale utente
Laney
Laney A1 Manuale utente
Laney
Laney NEXUS TUBE Manuale utente
Laney
Laney VC30-210 Manuale utente
Laney
Laney A 301 2 Manuale utente
Laney
Laney CUB 12 Manuale utente
Laney
Laney AOR Series Manuale utente
Laney
Laney Richter Bass RB2 Manuale utente
