Lanner UP-2010 Manuale utente
Network
Communications
Hardware Platforms for Network Computing
UP-2010
V1.1
User's Manual
Release Date: 2016/03/04
Overview
Icon Descriptions
The icons are used in the manual to serve as an
indication of interest topics or important messages.
Below is a description of these icons:
NOTE: This check mark indicates
that there is a note of interest and is
something that you should pay special
attention to while using the product.
WARNING: This exclamation point
indicates that there is a caution or
warning and it is something that could
damage your property or product.
Online Resources
The listed websites are links to the on-line product
information and technical support.
Resource Website
Lanner http://www.lannerinc.com
Product
Resources
http://www.lannerinc.com/download-
center/
RMA http://eRMA.lannerinc.com
Copyright and Trademarks
This document is copyrighted, © 2014 All rights are
reserved. The original manufacturer reserves the right to
make improvements to the products described in this
manual at any time without notice.
No part of this manual may be reproduced, copied,
translated or transmitted in any form or by any means
without the prior written permission of the original
manufacturer. Information provided in this manual
is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its
use, nor for any infringements upon the rights of third
parties that may result from such use.
Acknowledgement
Intel, Pentium and Celeron are registered trademarks of
Intel Corp.
Microsoft Windows and MS-DOS are registered
trademarks of Microsoft Corp.
All other product names or trademarks are properties of
their respective owners.
Compliances
CE
This product has passed the CE test for environmental
specifications. Test conditions for passing included
the equipment being operated within an industrial
enclosure. In order to protect the product from being
damaged by ESD (Electrostatic Discharge) and EMI
leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
Safety Guidelines
Follow these guidelines to ensure general safety:
Keep the chassis area clear and dust-free during and after•
installation.
Do not wear loose clothing or jewelry that could get•
caught in the chassis. Fasten your tie or scarf and roll up
your sleeves.
Wear safety glasses if you are working under any•
conditions that might be hazardous to your eyes.
Do not perform any action that creates a potential hazard•
to people or makes the equipment unsafe.
Disconnect all power by turning off the power and•
unplugging the power cord before installing or removing a
chassis or working near power supplies
Do not work alone if potentially hazardous conditions•
exist.
Never assume that power is disconnected from a circuit;•
always check the circuit.
LITHIUM BATTERY CAUTION:
Risk of Explosion if Battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions
Operating Safety
Electrical equipment generates heat. Ambient air temperature
may not be adequate to cool equipment to acceptable
operating temperatures without adequate circulation. Be sure
that the room in which you choose to operate your system has
adequate air circulation.
Ensure that the chassis cover is secure. The chassis design
allows cooling air to circulate effectively. An open chassis
permits air leaks, which may interrupt and redirect the flow of
cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and
impair electrical circuitry. ESD damage occurs when electronic
components are improperly handled and can result in complete
or intermittent failures. Be sure to follow ESD-prevention
procedures when removing and replacing components to avoid
these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes
good skin contact. If no wrist strap is available, ground yourself
by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap,
which should be between 1 and 10 megohms (Mohms).
EMC Notice
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case users will be required to correct the
interference at their own expense.
Revision Date Description
1.0 2014/12/30 Ocial release
1.1 2016/03/04 R e m o v e d P o E r e l a t e d
information
Consignes de sécurité
Suivez ces consignes pour assurer la sécurité générale :
Laissez la zone du châssis propre et sans poussière•
pendant et après l’installation.
Ne portez pas de vêtements amples ou de bijoux qui•
pourraient être pris dans le châssis. Attachez votre
cravate ou écharpe et remontez vos manches.
Portez des lunettes de sécurité pour protéger vos•
yeux.
N’effectuez aucune action qui pourrait créer un•
danger pour d’autres ou rendre l’équipement
dangereux.
•
Coupez complètement l’alimentation en éteignant•
l’alimentation et en débranchant le cordon
d’alimentation avant d’installer ou de retirer un
châssis ou de travailler à proximité de sources
d’alimentation.
Ne travaillez pas seul si des conditions dangereuses•
sont présentes.
Ne considérez jamais que l’alimentation est coupée•
d’un circuit, vérifiez toujours le circuit. Cet appareil
génère, utilise et émet une énergie radiofréquence
et, s’il n’est pas installé et utilisé conformément aux
instructions des fournisseurs de composants sans
fil, il risque de provoquer des interférences dans les
communications radio.
Avertissement concernant la pile au
lithium
Risque d’explosion si la pile est remplacée par une•
autre d’un mauvais type.
Jetez les piles usagées conformément aux•
instructions.
L’installation doit être effectuée par un électricien•
formé ou une personne formée à l’électricité
connaissant toutes les spécifications d’installation et
d’appareil du produit.
Ne transportez pas l’unité en la tenant par le câble•
d’alimentation lorsque vous déplacez l’appareil.
La machine ne peut être utilisée qu’à un lieu fixe•
comme en laboratoire, salle d’ordinateurs ou salle de
classe.
Table of Contents
Overview 2
Chapter 1: Introduction 5
System Specification 5
Package Contents 6
Chapter 2: System Components 7
Mechanical Drawing 7
Block Diagram 8
Front Components 9
Rear Components 10
Chapter 3: Motherboard Information 11
Inside UP-2010 11
Jumpers & Connectors on the Intel Rangeley Main Board 12
Jumpers & Connectors on the PCIe I/O Board 13
Connectors and Jumpers List 14
Jumper Settings & Connector Pinouts on the Intel Rangeley Main Board 15
Jumper Settings & Connector Pinouts on the PCIe I/O Board 18
Chapter 4: Hardware Setup 21
Preparing the Hardware Installation 21
Installing System Memories 21
Installing a CompactFlash Card 22
Replacing the PSU (Power Supply Unit) 22
Replacing the Cooling Fans 23
Appendix A: Programming Watchdog Timer 24
Appendix B: Setting up Console Redirections 24
Appendix C: On Linux 25
Appendix D: Terms and Conditions 26
Chapter 1:
Introduction
Thank you for choosing Lanner UP-2010. Lanner
UP-2010 is an enterprise-class 1U rackmount network
security appliance with high-density Ethernet ports and
PoE capability. Built with Intel® Atom™ C2000 processor,
the appliance can offer efficient packet processing
abilities and Intel® security instructions at low power
consumption. In addition, UP-2010 also comes with
Marvell® Prestera® processor to provide high-port
density to act as a switch. The appliance is highly ideal
for enterprise gateway controller, UTM, Switch or next-
generation firewall.
Features:
8 x PoE ports for wireless access points or IP•
cameras
High-port density with 24 x 1GbE RJ45 copper•
ports plus 2 x 10GbE SFP+
Intel® Atom™ C2758 8-core, 2.4 GHz•
Marvell® Prestera® 98DX3035 packet processor•
Built-in Intel® QuickAssist acceleration technology•
Supports DDR3 ECC memory•
1 console port, 1 management port, 2 x USB ports•
System Specification
Form Factor 1U Rackmount
Platform Processor Options Intel® Atom™ Processor
C2758 (4M Cache, 2.40 GHz)
Chipset N/A
BIOS 64Mb Flash Memory with
AMI® BIOS
System
Memory
Technology DDR3 ECC supported
Max. Capacity Up to 16GB
Socket 2 x 204 SO-DIMM
OS Support Supports 32-bit/64-bit
operating systems
Storage
1 x SATA 2.5” HDD/SSD
(optional)
1 x CompactFlash card
Network
Interface
Management Port
1 x RJ-45 by Intel I210
LOM Port N/A
Bypass N/A
Ethernet 1 x MGT port
24 x RJ45 ports
2 x 10G SFP+ ports
NIC module space N/A
I/O Connectors
Reset
Software / Hardware reset
(Control by GPIO) default SW
reset
Console 1 x RJ45 console
USB 2 x USB 2.0 ports
LED Power/Status/HDD
FAN
3x FAN connectors 5pin (support
SMART FAN)
IPMI 1x RJ-45 connector for IPMI
management
SATA 1 x SATA connector
Power supply
500W
Input 100-240V, 50-60Hz,
7-3.5A
System Cooling
2 x cooling fans (supporting
smart fan)
Thermal 1 x heatsink
Environment
Operating
Temperature 0º to 40º C
Storage
Temperature -40º C to 70º C
Operating
Humidity 5% to 90%
Dimensions (unit: mm) 431 X 44 X 355 (W x H x D)
Certication CE, FCC, RoHS
Package Contents
Your package contains the following items:
1 – WG-UP2010 POE Switch System•
2 – Power cable•
1 – Ear Rack mount kit with screws•
1 – Console cable•
1 – LAN Cable (Red)•
1 – Doc Kit for WG•
Note: If you should find any components missing or
damaged, please contact your dealer immediately for
assistance
Ordering Information
UP-2010
24 ports RJ45 (Marvell 98DX3035) w/o
bypass, Intel® Atom™ Processor
C2718 (4MB Cache, 2.00 GHz) FC-BGA13E,
Tray, MB-UP2010W + FCUPWG2010
Chapter 2:
System Components
Mechanical Drawing
Block Diagram
PSU
Intel
Rangeley
Platform
C2758
DDR3 1600
ECC SO-DIMM
CF Card
PSU
PCIex8 *2
Front Components
Component Description Remarks
F1 LED Indicators Power/Status/HDD
F2 Console 1 x RJ-45 port to be connected with a terminal PC for
diagnose and management purposes
F3 USB 2.0 Ports 2 x USB 2.0 type A connectors.
F4 Management 1 x RJ-45 management port
F5 LAN ports 24 x Ethernet LAN ports
F6 SPF ports 2 x 10GbE SPF network ports
F7 Power switch Power switch
F3
F1 F5
F2 F4
F6
F7
F10
Component Description Remarks
R1 Fan 2 x cooling fans
R2 PSU 500W power supply unit
Rear Components
R1 R2
Indice
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente