LANPARTE LA3D-S Manuale utente
USER MANUAL
Contact us for further questions
www.lanparte.com
LA3D-S manual
HONGKONG LANPARTE TECHNOLOGY LIMITED
Email:[email protected]
Tel:+86-0769-81889368
Fax:+86-0769-85841828
ADD:NO.39 2nd Xin an road
Changan Town Dongguan Guangdong China
DETACHABLE WIRED CONTROL GIMBAL
3-Axis Handheld Gimbal for Smartphone
LA3D-S
LA3D-S
1 Appearance and Design
Attention !
Be sure to install smartphone before turning on power
Pitch axis adjustment screw
1/4 -20 thread
hole inside
Counterweight
Smartphone clamp
(fits smartphones up to 3.1”wide)
1
Inverted Mode indicator
Micro USB port
for setting and
firmware upgrade
2pcs 18350
Li-ion batteries
Power button
2 Compatible With
Compatible with iPhone 4, 4s, 5, 5s, 6, 6s,
6 plus, 6s plus and similar size smartphone
3 Package Content
Serial No. Product Name QTY
3-Axis handheld gimbal platform
Gimbal handle
18350 Li-ion battery
Handle extender
Wired control cable(1.5m)
Micro USB cable (For battery charger)
Smartphone clamp
Battery charger
UP
LEFT
Power
indicator
Mode
RIGHT
DOWN
Speed
dial
Mode indicator
8
8
9Counter weight
9
32
4 Operation
1. Standby mode : Press the power button to enter standby
mode. When in standby mode the signal light willturn blue
and blink .
2.Operating Mode: To activate operating mode press the M
button for 5 seconds. To go back to standby mode press the
M button again for 5 seconds.
3. Reverse mode : ln standby mode press the RIGHT button
for 8 seconds. Inverted mode light indicates inverted mode
is activated. Repeat this to return to regular mode.
4.Reset unit : In standby mode press the DOWN button for
5 seconds, a red light blinks and all settings are restored to
factory default.
5. Sensor calibration : ln standby mode press the LEFT
button for 5 seconds and a green light starts blinking. Once
the calibration is done the green light turns to red.
Balance the platform before calibration.
5 Power Display
Power Indicator Status
Indicator Status
75%-100%
50%-75%
25%-50%
Below 25%
Light blinks 4 times
Light blinks 3 times
Light blinks 2 times
Light flashes continously
Note : For better performance change the battery when the power is below
25%, as it might affect the stability of the platform.
6 Gimbal Basic Parameters
Rotation Angles
Yaw Roll Pitch
Size
Weight : 414.5g
(w/o battery)
315 70 140
54
7 Mode Switching
Operating
Mode
Activating
By
Mode
Indicator Locked
axis
Control
Buttons
Follow mode
Semi-follow
mode
Locked mode
Press M button
twice in less
than 1 sec
Press M button
three times in
less than 1 sec
Press M
button once
Green
Red
Blue
Roll
Pitch & Roll
Pitch
Roll & Yaw
LEFT and RIGHT
adjust roll axis
UP and DOWN
adjust pitch axis
UP and DOWN
adjust pitch axis,
LEFT and RIGHT
adjust yaw axis
* Use rotor speed dial to adjust all three rotor speeds.
UP
LEFT
Power
indicator
Mode
RIGHT
DOWN
Speed dial
Operating mode and Axis status
Axis
Mode Pitch Roll Yaw
Follow mode
Semi-follow
mode
Locked mode
Following
Locked
Locked
Locked
Locked
Locked
Following
Following
Locked
8 Platform Installation
Turn counter
clockwise to open
Turn clockwise
to lock
Make sure the two white dots
on the handle are aligned with
the dots on the gimbal platform
*Same process to
connect the wired control cable
*Ensure that the prongs are in contact
with each other before tightening the locking knob 76
9 Optional Accessories
Standard 1/4 -20
thread hole on bottom
+
++ +
+
10 Battery Instructions
Please note that the nominal voltage of the LA3D gimbal is 7.4V.
Each 18350 & 18650 battery is 3.7V. Therefore, the gimbal MUST
operate on a maximum of TWO batteries.
Batteries must be combined as per below scenarios:
Scenario 1: Scenario 2:
Scenario 3:
(with extender tube) Scenario 4:
(with extender tube)
3.7V + 3.7V = 7.4V 3.7V = 3.7V
3.7V + 3.7V = 7.4V 3.7V+3.7V+3.7V= 11.1V
Handle extension tube
Extending the tube to
install 2pcs 18650 batteries.
11 Battery Extender
Add extension before installing
the optional 2 * 18650 batteries
98
12 Battery and Charger
Rechargeable battery
Li-ion battery charger
Model : 18350 Li-ion battery
Capacity : 900mAh
Charging time : 3h
lnput : DC 5V/800mAh
Output : DC 4.2V/400mAh x 2
Charging Indicator
(Green light will appear once
the battery is fully charged)
Power input Micro
USB Port
*Note :18350 battery charger can be charged by using one of the following
( a )Power Bank
( b )A PC with USB port
( c )Smartphone Charger
13 Parameter
Item Parameter
Operating voltage
Operating current
Pitch angle
Roll angle
Yaw angle
Battery operating time
Operating Temperature
Net weight
Product Dimension
Package Dimension
6.5V - 12.6V
Standard 120mA
± 70
± 35
± 157.5
Standard 2h
- 10 ~ 40
414.5g(w/o battery and smartphone)
300.4 * 205.4 * 92.4(mm)
21 * 17 * 18(cm)
14 Ｑuick Start Guide
Step 1: Connect the grip to the gimbal platform (align the white dots
before turning the knob)
Step 2: Install smartphone into the clamp and adjust until it is balanced
horizontally and vertically
Step 3: Unscrew the power button at the end of the grip and install the
two 18350 batteries
Step 4: Turn the gimbal on by pressing the white power button
Step 5: Hold the M button for 5 seconds to will stabilize the gimbal
(it will always default to Mode 1 or follow mode); Double-tap
the M button to switch to Mode 2; Triple-tap the M button to
go into Mode 3; Single-tap to return to Mode 1
*Instructions of above Step 2
For iPhone 4, 4s, 5, 5s, 6, 6s and similar size smartphones
a .Make sure the phone is centered in the clamp. To check the balance, hold
the gimbal with the phone screen facing down.Loosen the back adjustment
knob and adjust so the screen is even with the floor.Tighten the knob.
the knob
1110
b. Now set the gimbal down.Make sure the counterweight is on the far left.
Slide the phone left to right until it is horizontally balanced.
c. Loosen the vertical axis adjustment screw and move the phone forward
or backward until it is vertically balanced. The gimbal is now ready to be
powered on.
For iPhone 6 plus, 6s plus and similar size smartphones
a. Remove the counterweiter
b and c same as above (except the counterweight)
the vertical axis adjustment screw
12
Indice
Altri manuali LANPARTE Accessori per fotocamere
