Lanpro LP-1522 Manuale utente
Wireless - Equipment
www.lanpro.com
123 Manual, LP-1522 Broadband Wireless AP/Router
Client Mode Installation.
LP1522_M123_END02W
123 Manual, LP-1522
Broadband Wireless AP/Router
Client Mode Installation.
www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP1522- 123 Manual Client Mode Installation
www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
Client Mode Installation.
2
Please check box contents, please see gure 1.
Figure 1
1
Please screw the antenna to the antenna connector as
shown in gure 2. If the antenna uses a pigtail cable,
please verify that the antenna is correctly connected to the
other end to avoid damaging the RF output stage of the
equipment when turned on.
2
Connect your PC or Switch to the LAN port of your LP-1522,
as shown in gure 3-1. In case you want to power it through
the PoE option, please connect the UTP cable to your LP-
PoE150 injector Power + Data port as shown in gure 3-2,
please remember that the cable length recommended
maximum is 60m. Then connect an UTP cable from the
Data In port of your LP-PoE150 to your PC or Switch as
shown in gure 3-3.
3
Figure 3-1 Figure 3-2
Figure 3-3
Connect the DC electric power plug to the power Jack as
shown in gure 4-1, remember that the alternate way
to power the LP-1522 is through the UTP port with PoE
technology by using a LP-PoE150 injector(Not included). If
used, please connect the LP-PoE150 to the mains as shown
in gure 4-2.
4
Figure 2-1 Figure 2-2
Figure 4-1 Figure 4-2
www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
Client Mode Installation.
3
Go to the Local Area Connection Properties window of your
network card (shown in gure 5) and select: Internet
Protocol, then: Properties.
5
Figure 5
In the window shown in gure 6, please select: Use the
following IP address and then input an IP address in
the range of IP addresses by default of the LP-1522. In
this example we have selected the following address:
192.168.1.201. The default address of the LP-1522
is: 192.168.1.254. Input now in : Subnet Mask:
255.255.255.0 In: Default Gateway, input the
destination Router address, in: DNS, input the DNS address
of your ISP or the destination router address that supplies
the Internet Service, this is for any queries that need to
be sent to the destination router, please see the diagram
shown in gure 6
6
Figure 6
Once the selection is nished, please select: Ok, then, OK
again and then : Close
It is important to mention that in this conguration of the
LP-1522 it will become a client of the destination network.
We suggest the following drawing in gure 7 as a guide.
7
Figure 7
www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP1522- 123 Manual Client Mode Installation
www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
Client Mode Installation.
4
In this diagram, the destination network is the yellow colored one. In it, there exists a router that provides the Internet
connection and has been enabled to deliver IP addresses in the segment: 192.168.1.x, with the rest as reserve. This router
will only deliver IP addresses from 100 to 200 and the Internet service. The blue colored network is the segment assigned
to your LP-1522 in which it has a default address of 192.168.1.254.
8
In gure 8, please open your selected browser and input the default address: 192.168.1.254
9
Figure 8
In the window shown in gure 9, please select: Wireless,
Basic Settings, in: Mode , select: Client, then select:
Apply Changes, the equipment will re-initialize:
10
Figure 9
In the window shown in gure 10, you will congure the
wireless connection security setting if the router has it as
enabled. Please remember that in this conguration, the
LP-1522 behaves as a client of the destination router.
Congure the security as if it were another client of this
network. Please take in mind that the WPA Mixed security
mode is not supported in the Client Mode.
Select: Wireless, Security, and in mode: Encryption,
use the corresponding ne and the input the password. The
select: Apply Changes.
11
Figure 10
In the gure 11, the window showing that the changes were made, select: Ok, once done, the equipment reboots.
12
Figure 11
www.lanpro.com
Wireless - Equipment - 2.4 GHz - 123 Manual - LP-1522 - Broadband Wireless AP/Router
Client Mode Installation.
5
Now we proceed to connect to that network. In order to do this, in the window of gure 12 select: Wireless, Site Survey
and select the network you wish to connect to, then select: Connect. If the network doesn’t appear, select: Refresh in
order to be able to see it.
13
Figure 12
Once connected, a message will pop-up shown in gure 13.
14
Figure 13
Once the conguration has been done, the LP-1522 will connect automatically even though you disconnect it and connect
it again.
15
Important Recommendation (Optional)
As shown in gure 14, proceed to change the administrative
password of your equipment. In order to do this, please
select: Management, then: Password, input the user
name: admin then the new password in: New Pasword
and again in Conrmed Passwword. Then select: Apply
changes. These data should be input again in order to
have access to the equipment.
16
Figure 14
Altri manuali per LP-1522
8
Indice
Altri manuali Lanpro Router di rete
Lanpro
Lanpro LP-1522 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-SW511 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-289ai Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-SW811 Manuale utente
Lanpro
Lanpro LP-LB404 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza