Lanpro LP-5a Guida utente
Wireless - Equipment
www.lanpro.com
LP-5a Setup 123 Manual.
LP5a_M123_END01W
LP-5a
Setup 123 Manual.
www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-5a Setup 123 Manual
The following Setup 123 Manual will guide you on how to setup and mount your LP-5a. It is highly recommended that con-
guration is preceded to physically mounting it. For additional information, please review the Installation Guide included in the
CD or by downloading it from the page: www.lanpro.com.
Please check the package contents compared to the parts shown in gure 1.
Figure 1
Proceed to x the base to the wall (See gure 2) or to the mast (Please see gures 3 and 4).
a
1
2
Proceed to turn the radio over, in order to place the base on the back of the radio as shown in gure 5 and 6.
Figure 5 Figure 6
b
Figure 2 Figure 3 Figure 4
Preparation of the wall or mast mounting base.
2
www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-5a Setup 123 Manual
3
4
Figure 7 Figure 8
Proceed to join the bases and insert the corresponding screws and washers, as shown in gures 7 and 8.
c
Cable preparation for powering the LP-5a with PoE injector.
Antenna connection. Fix the antenna as shown in the antenna instructions. Use the proper RF cable, screw the antenna
connector to a surge arrester like the LP-G11 from LanPro, and continue from the surge arrester to the LP-5a N connector
with another RF cable. Figures 10 show the details.
The recommended cable is the LP-214502 Outdoor Cat5e Cable by LanPro, and should be prepared as per the proper
wiring standard used in the downstream hardware. If grounding standards are stringent, cable should be of the braided
type and the braid connected at the shielded RJ-45 plug.
Figures 9a and 9b show the two possible schemes used for sealing the RJ-45 connector against moisture.
Figure 9a
Figure 9b
Figure 10
a
3
www.lanpro.com
Wireless - Equipment - 5.8 GHz - LP-5a Setup 123 Manual
6
Connect a patch cord from the Switch or PC to the Injector port (To Ethernet) and connect the power input to the PoE
injector as shown in gures 12.
4
5
Now proceed to connect the cable prepared in paragraph 3 to the LP-5a with the other end to the PoE injector (To Odu port).
Please see gure 11.
Remember to ground the radio following your country regulations.
Never turn the radio on without the antenna correctly connected or you will certainly damage the output stage.
e
f
Figure 11
Figure 12
The recommended RF cables is the LP-C400 from LanPro.
Don’t forget to install a surge arrester with proper grounding to the nearest buried grounding copper bar.
c
d
The connector shal be oriented as shown in gure 10.
Utilization of vulcanizing tape is mandatory to ensure proper sealing against moisture.
a
b
Please take the following precautions:
Indice
Altri manuali Lanpro Router wireless
Lanpro
Lanpro LP-1522 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-N24 V2.0 Manuale utente
Lanpro
Lanpro LP-5420G Manuale utente
Lanpro
Lanpro LP-1522 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-N24 V2.0 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-N24 Manuale utente
Lanpro
Lanpro LP-1521 Manuale utente
Lanpro
Lanpro LP-5420G Manuale utente
Lanpro
Lanpro LP-1522 Manuale utente
