LarsLap S Manuale utente
LarsLap Model S
Tools with the cutting edge
1
LarsLap
Model S
Users Guide
LarsLap Model S
Tools with the cutting edge
2
Welcome to the LarsLap family
Thank you for choosing LarsLap Valve grinder model S.
By choosing a LarsLap valve grinder you have received a high quality product
where we have carefully selected parts with great care for est possi le
performance.
To achieve a long and trou le free lifetime of your LarsLap Valve grinder, we ask
you to read this operation manual thoroughly efore you take the machine in
use and only to use original spare parts or parts recommended y LarsLap.
If there would e pro lems that are not included in this operation manual, we
ask you to contact your LarsLap dealer for further instructions.
We wish you good luck with your LarsLap valve grinder.
LarsLap
Helena Larsson Häger
President
LarsLap Model S
Tools with the cutting edge
3
Contents Page
Safety Instructions 4
Instructions Prior and After Use 5
Parts 6-7
ow to use your LarsLap Valve Grinder 8-11
-Before you start 8
-Grinding a Gate Valve 9-10
-Grinding a Gate Valve Wedge 11
Recommended Service 12
Choosing Grinding Material 13
Recommended Grinding Abrasives 14
Accessories 15
LarsLap Model S
Tools with the cutting edge
4
SAFETY INSTRUCTIONS
-Keep the working area clean. Dirty areas may cause injury.
-Evaluate working environment. Make certain that lighting is
satisfactory.
-Use suitable clothing. Do not wear loose clothes or accessories it can
cause injury.
-Wear protective goggles and ear protection. Use face or dust mask as
needed.
-Stand firm. Stand on steady ground and maintain alance while
working.
-Make certain that the air supply valve is in a closed position efore
connecting air.
-Before start, check the machine for damaged parts and make sure that
safety arrangements are working.
-Make sure that all adjusting keys, wrenches and other tools are
removed before starting the machine.
-Be alert, and keep your eyes on the jo . Use common sense. Do not
operate the machine if you are tired or taking medication.
-andle the machine with care. Careless handling can affect the
machine capacity and accuracy.
-Keep wires and ca les from heat oil and sharp edges.
-Do not overload the machine. Performance is est at designated load.
-Store all tools in the supplied case. Keep the case in a locked and dry
facility.
-Keep unauthorized people away. Do not permit untrained visitors or
staff to e in contact with the tools.
-Use of parts not authorized y LarsLap may cause damage to the
equipment and could cause injury to the operator.
-Personnel authorized y LarsLap must repair damaged machinery.
-
Caution!!!!
All electrical equipment must e handled with care. Do not
under any circumstances open parts of the electrical motor or charger!
This can cause serious body injury or death y electric chock or damage
the machine.
-
Never use a attery charger on floor or ground, keep away from water
and dust. Damaged charger may not e used.
LarsLap Model S
Tools with the cutting edge
5
Instructions prior to and after use
Your valve grinder model S is manufactured and
tested according to LarsLap specifications and high
standards. To ensure your S a long and trou le free
lifetime, please follow the instructions elow.
Prior to and after use you must consider the following:
-Check all parts to make sure that they are not dama-
ged or have een influenced so that the performan-
ce can e effected, if so contact your LarsLap dealer
for further instructions.
-That all parts are cleaned from water, dirt, oil and
grinding dust.
-Check the schedule provided in the case that no parts
are missing efore and after use.
LarsLap Model S
Tools with the cutting edge
6
Parts
A fully equipped LarsLap model S-C 100 valve grinder consists of:
Part no. Qty Description Picture
40 101 00 1 Gate valve drive shaft including
pneumatic reversi le motor
40 004 00 1 Machine frame
40 005 00 1 Wedge plate
40 006 00 1 Mounting plate
90 301 01 1 Regulator (pneumatic option)
93 300 01 1 Grinding plate DN 25 mm
93 300 02 1 Grinding plate DN 32 mm
93 300 03 1 Grinding plate DN 40 mm
93 300 04 1 Grinding plate DN 45 mm
93 300 05 1 Grinding plate DN 50 mm
93 300 06 1 Grinding plate DN 65 mm
93 300 07 1 Grinding plate DN 80 mm
93 300 08 1 Grinding plate DN 100 mm
LarsLap Model S
Tools with the cutting edge
7
Part no.
Qty
Description
90 531 01 100 Grinding disc SPA P80 17mm
90 531 02 100 Grinding disc SPA P80 20mm
90 531 03 100 Grinding disc SPA P80 25mm
90 531 21 100 Grinding disc SPA 100µ 17mm
90 531 22 100 Grinding disc SPA 100µ 20mm
90 531 23 100 Grinding disc SPA 100µ 25mm
90 531 41 100 Grinding disc SPA 100µ 17mm
90 531 42 100 Grinding disc SPA 100µ 20mm
90 531 43 100 Grinding disc SPA 100µ 25mm
90 900 26 1 Hexagon screw driver 6 mm
1Hexagon screw driver 3 mm
1Allen key set 1,5 – 6 mm
1Measuring tape 2 m
1Flash light
10 103 33 1 Operations manual
10 101 11 1 Spare parts kit
Check the specifications for your machine and make
sure that it has been delivered complete.
LarsLap Model S
Tools with the cutting edge
8
ow to use your LarsLap valve grinder
Before you start:
1. Make sure that no parts are missing or damaged, if
necessary contact your LarsLap dealer for advice.
2. Measure the internal (A) and external (B) diameter of the
seat.
3. Measure the distance (C) etween the center of the seat
and the flange top.
4. To make sure that the machine and grinding-material will
work as expected, clean the valve from moisture and dirt.
5. In the case that you S is equipped with a pneumatic drive
unit, make sure that you have a sufficient air supply with a
maximum of 8 ar.
6. After measuring A and B choose the correct grinding plate.
7. Before you assem le the grinding heads, make sure all con-
tact surfaces are cleaned carefully.
8. Mount the grinding plate on the drive shaft as shown on the
pictures.
9. When the grinding plate is assem led on the drive shaft
check it in the valve to make sure that there is adequate
space.
*Grinding of a gate valve, continue on page 9
*Grinding of a gate valve wedge, continue on page 11
LarsLap Model S
Tools with the cutting edge
9
Grin
ding of a ga
te
val
ve bo
dy.
Model S
Continued from How to use your LarsLap valve grinder on page 8
11. Assem le the mounting plate. Ensure the pointed gru
screws on the clamp (A) are visi le 6-8 mm. Fasten the
mounting plate on the flange or valve ody and lock y
tightening the clamp screw (B) with a torque a out 20 Nm.
To make the grinding easier the mounting plate should e
placed ehind the seat, ut can, if necessary e placed
anywhere around the flange. Make sure that all 3 pointed
gru screws (A) are locked on to the ody.
12. If the flange has non remova le olts a recommendation is
to use the mounting device for narrow seats (part num er
90 401 00).
13. Assem le the machine frame so that the drive shaft clamp
reaches out, over the seat, this to make sure you receive a
positive angle etween the drive shaft and the seat.
Tighten the 4 screws (C). Adjust the drive shaft mount plate
to a perpendicular position with the pressure feed (D).
14. Attach the grinding discs on the plate as shown on the
picture (see recommendation on page 16).
Always start with a finer grit and check the seat after one
minute of grinding. If the damage is small continue with
the same grit or finer.
15. Hold the drive unit steady and mount it on the machine
frame and make sure that the fixed point depth
adjustment clamp point (E) falls in position. Set the vertical
position of the unit y releasing and tightening the
adjustment clamp (F). Lock the drive unit using the two
kno s (G). For adjustment in the horizontal plane, use the
side adjustment kno (H). Remem er to use care while
adjusting the drive shaft depth, a dropped drive shaft could
cause damage to the equipment. Adjust drive shaft angle
y using the grinding pressure kno (I).
16. Attach the speed regulator on the mounting plate y using
the two screws (J). Connect the air hose to the speed regu-
lator. Make sure that the shut off valve (K) is closed efore
you connect the air supply and that the air regulator (L) is
closed (turned counterclockwise). To e a le to operate
the kno you have to lift the kno and then turn.
A
B
C
D
E
F
G
I
K
L
H
J
LarsLap Model S
Tools with the cutting edge
10
17. Add a light grinding pressure a out 0,5 kg. Start the machine
slowly y opening the shut off valve (K) maximum and then turn
the regulator kno (L) clockwise until correct speed is reached
(60-80 rpm). Add sufficient grinding pressure 1-2 kg (half to a
whole revelation on the grinding pressure kno ).
18. Change direction of the rotation every 2-3 minutes to get the
most out of the grinding discs. You might have to adjust the air
input when working the air motor in reversed direction due to
power loss.
19. When changing grinding discs, stop the machine y turning of the
shut off valve (M) and disconnect the air hose. Release grinding -
pressure and loosen the drive unit with the clamp kno (H) and
then lift the whole drive unit out of the valve and change grin-
ding discs. When the discs are switched, re-install the drive unit
ack in the valve and tighten the clamp kno (H), re-connect the
air supply, add grinding pressure and continue the grinding -
procedure.
20. To grind the seat on the opposite side. Rotate the driveshaft 180°
and add pressure the opposite way.
21. When you are done grinding go thru the machine and check for
damages. Make sure that all parts are cleaned and dried efore
you put them ack in the case. Do a final check that all parts are
in the ox.
Indice
