Lassco Wizer Spinnit EBM-S Manuale utente
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Lassco Spinnit
EBM-S Paper Drill
User's Manual
Before operating this equipment, please read these
instructions completely and keep these operating
instructions for future reference.
Serial Number:
Date of Purchase:
Dealer:
Address:
Telephone Number:
485 Hague Street, Rochester, NY 14606 U.S.A.
Tel: 585-436-1934 Fax: 585-464-8665
www.lasscowizer.com info@lasscowizer.com
Table Of Contents
Introduction
Operating Instructions
Maintenance
Trouble Shooting Guide
Introduction.......................................................................
Shipping Damage Inspection............................................
Page 02
Page 02
Safety Information
Safety Instructions............................................................
Warning Labels.................................................................
Page 03
Page 03
Setting Up Your Machine
Loose Materials Inventory.................................................
Back Gauge Assembly......................................................
Stop Collars and Paper Side Stop.....................................
Chip Bag...........................................................................
Electrical Start Up.............................................................
Page 04
Page 05
Page 05
Page 06
Page 06
Parts Diagrams
Front, Back, and Side View...............................................
Interior Front and Back.....................................................
Parts List...........................................................................
Page 12
Page 13
Page 14
Drill Bit Removal and Installation......................................
Leveling The Drill Bits.......................................................
Drilling...............................................................................
Clearing the Chips............................................................
Tips On Drilling.................................................................
Page 07
Page 08
Page 08
Page 09
Page 09
Every 6 Months................................................................. Page 10
Problem, Cause and Correction........................................
Page 11
Page 01
Introduction
Shipping Damage Inspection
Page 02
Thank you for your purchase of the Spinnit EBM-S Paper Drill. Lassco-Wizer
has been designing and manufacturing proven performance equipment for the
graphic arts, office, screen printing, sign, awards and engraving industries for
over 60 years.
We ask that you take a moment to fill in the serial number and other information
on the front cover of this manual. Please keep this manual as a reference for
future use.
For parts and service please contact the Lassco-Wizer Dealer from whom you
purchased the machine. If you require assistance in locating a Lassco-Wizer
Dealer nearest you, please contact our customer service department at
585-436-1934. Please have the model of your machine and the serial number
when you call.
If you wish to write to us please contact us at:
Lassco-Wizer
485 Hague Street
Rochester, NY 14606
Remove the machine from the carton and inspect for any shipping damage. If any
damage is present, report the damage to the carrier immediately. Failure to do so
may void any warranties.
Introduction
Safety Information
Page 03
All operators must read and understand the Users Manual and all other safety instruc-
tions before using this equipment. If after reading the manual you are still uncertain
about use, please contact a Service Technician for assistance. If you need contact
information for a Service Technician nearest you please call 585-436-1934. Failure to
fully understand the safety instructions can result in personal injury.
This machine is designed for one person operation. Never operate the machine with
more than one person.
Safety of this equipment is the responsibility of the users.
Keep hands, hair, and loose clothing away from the drills.
Please read and follow all warning labels on your machine.
Always turn the machine off and wait for the drills to stop spinning before installing or
removing drill bits. Keep hands away from drills when operating. PLEASE NOTE THAT
THE DRILL BITS MAY BE HOT AFTER USE. PROCEDE WITH CAUTION WHEN
CHANGING THE DRILL BITS.
ONLY A SERVICING TECHNICIAN IS TO SERVICE THIS MACHINE.
Warning Labels
Safety Instructions
The following labels appear on your EBM-S paper drill. Make sure
all operators understand and follow the safety instructions.
Please read and make sure that all operators understand the operators
manual and all other safety instructions before using this equipment.
Keep hair, jewelry, loose clothing and any other items that could become
entangled pulled back away from the machine when drilling.
Setting Up Your Machine
Loose Materials Inventory
Page 04
Remove and inspect the following items:
EBM2-1048: Chip Bag (1)
EBMS-115A: Backgauge Assembly (1)
EBM-10: Drill Block (1)
This item comes installed
This item comes installed
Hollow Drill BIt (1) Spin-Eze:
Drill Bit Lubricant (1)
CC-2: Chip Clearer (1) EBM-32:
Chuck Release Key (1)
HEX-332:
Hex Wrench 3/32” (1)
HEX-18:
Hex Wrench 1/8” (1)
Setting Up Your Machine
Back Gauge Assembly
Stop Collars and Paper Side Stop
Page 05
Attach the Backguage (EBMS-115A) to the Table by hooking
the left end over the Side Iron (FM4-4003) on the side as
shown in the accompanying pictures. Align both ends of the
backgauge using the Table Scales so that it is squared
correctly. When it is positioned as desired, tighten down the
Backguage Clamp (EBMS-10) as shown.
For multi hole drilling, adjust the Stop Collars (EBM-47) by
loosening them with the provided Hex Wrench (HEX-332).
Slide the Stop Collars (EBM-47) to the desired positions and
tighten. Slide the Paper Side Stop (EBMS-8001) against the
Stop Collars to brace it in place. When its time to drill slide
the product up against the Paper Side Stop and hold in
place.
Step #1
Step #2
To slide the Paper Side Stop to the next Stop Collar, lift up on
the Paper Side Stop releasing the bracing pin from hitting the
Stop Collar as shown. Slide the Paper Side Stop past the
Stop Collar and set it down so that it braces against the next
Stop Collar.
Step #3
Note: Do not position the Backgauge too close to the hollow drill bit so
that it touches. This can cause serious damage to the hollow drill
bit causing it to break or shatter. The Backgauge must be at least
1/8” from the circumference of the hollow drill bit.
Setting Up Your Machine
Page 06
Your Spinnit Paper Drill is now ready for use. With proper operation and
maintenence, it will give you trouble free operation for years.
Electrical Start Up
Making sure nothing is interfering with the drill bit,
plug the cord set into a grounded 115V outlet. To
turn the machine on, press the Rocker Switch located
on the upper left hand side of the shroud.
Step #7
Power Cord
Rocker Switch
Chip Bag
Attach the Chip Bag (EBM2-1048) as shown by stretching
the open end over the top hook of the Chip Chute (EBM2-
110A). Continue fitting it around the entire edge of the Chip
Chute making sure it is snug.
Step #4
Note: Be sure to empty the Chip Bag regularly as needed. Failure to
empty the Chip Bag can result in clogging of the Chip Chute.
Operating Instructions
Drill bit Removal and Installation
Page 07
Remove the hole guard which is attached to the Chuck. This
is done by grasping the bent end and sliding the guard off.
Step #1
Using the Chuck Release Key (EBM-32), insert the tapered
end facing down into the chuck hole. With a clockwise motion
turn the Chuck Release Key 45 degrees. The drill bit will slide
out of the chuck. It is recommended that you hold onto the
drill bit so that it does not drop out of the chuck damaging the
tip.
Step #2
To install a drill bit, grasp the drill bit, and being careful to keep
it straight, press it up into the chuck.
Step #3
Seat the drill bit by using a stack of scrap paper or a phone
book. Set the scrap on the table as shown and pull lightly
down on the handle to raise the table toward the drill bit. Put
light pressure on the hollow drill bit seating it firmly in place.
Remove the scrap paper and turn the machine on to check the
concentricity of the bit. If the bit is not concentric, remove it
and repeat steps 3 and 4 until it is concentric. When the drill
bit is correctly installed replace the hole guard back onto the
chuck to protect debris from clogging the chuck.
Step #4
Note: Please note that drill bits may be hot after drilling. Please wait to
change drill bits until they have cooled down.
Operating Instructions
Leveling The Drill Bits
Page 08
To level the drill bits to the Table, first loosen the
Leveling Knob on the right hand side of the machine
as shown. Pull down on the Handle to raise the Table
until the hollow drill bit is just touching the Drill Strip
(EBM2-1034). Hold the Handle in place and tighten
down the Leveling Knob until it hits the Handle
Bracket. This will stop the Handle from being pulled
down too far. It is important to always reset the Level
with each use. This will make sure you don’t drill into
the Drill Strip, dulling the drill bit.
Step #6:
Note: We recommend using a piece of card stock on the Table
when leveling the drill bits to avoid drilling into the drill block.
This will lengthen the life of your drill bits and keep them
When you are ready to drill, set the product to be
drilled on the table. Turn the machine on and holding
the product firmly in place with one hand, pull down
on the Handle raising the Table up to meet the drill
bit. Using one consistent smooth stroke, put pressure
on the Handle so that the Table rises fully allowing the
drill bit to drill through the product. It is important you
maintain a consistent speed through the entire stack.
It is also important you do not go too slow or too fast.
If you drill too slow you can burn the paper leaving
undesired marks. If you drill too fast, the drill bits will
act more like a punch and they will break or plug.
Step #7:
Drilling
Indice
Altri manuali Lassco Wizer Taglierina per carta
