Launch Creader Professional 123 Series Manuale utente
Quick Start Guide
Display Tablet
123X
There are two charging methods available:
Via Charging Cable: Plug one end of the included charging cable into
the 5V charging port of the tool, and the other end to the external DC
power.
Via Diagnostic Cable: Insert one end of the diagnostic cable into the
DB-15 connector of the tool, and the other end to the vehicle's DLC.
Once the charging LED illuminates solid green, it indicates that the
battery is fully charged.
Press the [Power] button to power it on.
If it is the first time you have used this tool, you need to make some
system settings and keep the diagnostic software synchronized with
the latest version.
Follow the steps below to proceed.
Charging & Turning On
Getting Started
1
2
Tap “Start” on Welcome screen
Select system language
Select time zone
WLAN setup
Configure email address
Sign user agreement
Job Menu appears
Tap “Update”
LAUNCH
*Note: After you configured it,
the system will automatically
send the diagnostic report to your
email box every time a complete
Auto-Detect process is
successfully finished.
*Note: To enjoy more capabilities
and better service, you are
strongly recommended to update
it on regular basis.
*Note: If you choose "Ignore" in
this step, it will go into the date
setting page. If the tool has been
properly connected to the Internet,
the system will automatically
obtain the correct network date and
time.
8" Touch Screen
Selection Buttons
HOME Button
Charging LED
OK Button
Return Button
(Red: Charging.
Green: Fully
charged.)
Power/Screen
Lock Button
DB-15 Diagnostic Connector
5V Charging Port
(To connect to vehicle's DLC (Data
Link Connector) via diagnostic cable.)
(To connect to external DC
power for charging the tool.)
Quick Start Guide
123X
Preparation
3
Diagnostic Cable
1. Turn the ignition off.
2. Locate vehicle's DLC: It
provides standard 16 pins
and is generally located on
driver's side, about 12
inches away from the
center of dashboard. See
Figure DLC Location. If
DLC is not equipped under
dashboard, a label
indicating its position will
be given.
3. Plug one end of the diagnostic cable into the DB-15 connector of
the tool, and tighten the captive screws. Connect the other end to
the vehicle's DLC.
Vehicle
DLC
Display Tablet
*Note: The tool ONLY works with the 12V passenger cars equipped with
standard OBD-II diagnostic socket.
4. Turn the ignition key on.
In case no DLC is found, please refer to Automobile Repair Manual.
Start Diagnostics
4
AutoDetect and manual diagnosis are supported. If the AutoDetect
fails, you can choose to input the VIN manually or exit the AutoDetect
session to switch to manual diagnosis mode.
Tap “Diagnose”*
Start decoding vehicle VIN
Decoding OK Decoding failed
Double check vehicle info.
Select vehicle manufacturer
Scan all vehicle systems
Select vehicle make
Output diagnostic report
Select test system
Select diagnostic function*
Diagnostic Flowchart Manual Diagnosis Flowchart
*If you are fresh to vehicle
diagnostics, you are suggested
to use "DEMO" to get familiar
with the diagnostic process.
Input the VIN, and tap "OK", the system will automatically identify the
vehicle model. If the vehicle VIN is successfully decoded, it will perform
auto-diagnosis until a diagnostic report is automatically output.
*Note: The most recognizable location for VIN is in the top left corner on the
vehicle's dashboard. Other locations include the driver's door or post, and the
firewall under the hood.
*Note: If "Automatic detection on connect" in "Settings" is set as ON, this
step can be ignored.
overseas.service@cnlaunch.com
+86 755 8455 7891
制作要求：
原始文件大小： 210mm x 148mm, 按1:1输出， 正反两面
印刷要求： 黑白印刷, 80g内页纸
正面
Altri manuali Launch Apparecchiature diagnostiche
Launch
Launch X-431 V+ Manuale utente
Launch
Launch CRT 7 Series Manuale utente
Launch
Launch X-431 Torque LINK Manuale utente
Launch
Launch CReader Professional CRP329 Manuale utente
Launch
Launch iCarScan Manuale utente
Launch
Launch Creader Professional 123E Manuale utente
Launch
Launch X-431 PAD V Manuale utente
Launch
Launch X-431 IMMO Pro Manuale utente
Launch
Launch Creader 7001S Manuale utente
Launch
Launch X-431 PROS V4.0 Manuale utente
Launch
Launch X-431 PRO3S+ Manuale utente
Launch
Launch X-431-IMMO Pad Manuale utente
Launch
Launch Creader 519 Manuale utente
Launch
Launch X-431 EURO TURBO Manuale utente
Launch
Launch CRP229 Manuale utente
Launch
Launch X431 V Manuale utente
Launch
Launch X-431 IMMO ELITE Manuale utente
Launch
Launch Creader Professional 229 Manuale utente
Launch
Launch Creader Professional 129i Manuale utente
Launch
Launch X-431 PADII Manuale utente
