LazyPro AC750 Manuale utente
Created for Smart Laziness
AC750 | AC1200 Setup Guide
AC1200 AC750
Watch the step-by-step setup
video guide on our official
YouTube channel at
www.clients[email protected]
SIGNAL LED
WPS LED
PWR LED
Created for Smart Laziness
LED DESCRIPTIONS
Solid on
The repeater has started.
Off
The repeater is not powered on.
PWR LED
On
A WPS connection has been established.
Blinking
A WPS connection is being established.
Off
The WPS function is disabled.
WPS LED
Solid BLUE
The repeater has connected to your
existing WiFi router, and its position
is proper.
Solid RED
The repeater is too far away from the
router. Relocate the repeater closer to the router.
Off
The repeater is not connected to your WiFi router.
SIGNAL LED
AC1200 AC750
METHOD
EXTENDING YOUR WIFI NETWORK USING WPS
STEP 1
You can use Method 1 if your router has a WPS button (possible icons of
a WPS button: , or ). Some routers only allow to activate the WPS
function via the web interface of the router. If your router does not have
the WPS function, use Method 2.
Power on the Repeater
Plug the repeater into a power outlet
near the router in the same room.
Wait until the PWR LED turns solid
blue.
Double check if the encryption type of your main
router is WPA-PSK or WPA2-PSK. WPS connection
does not support WEP security type
Created for Smart Laziness
STEP 2
ExtendYour WiFi Network
Activate the WPS function on your main router either by pressing the
WPS button on your router or via web interface of the router; once
the WPS function is activated, press and hold the WPS button on the
repeater for 3 seconds
Wait until the Signal LED on the repeater turns solid blue which means
that the repeater has successfully connected to your router. The name
of the new extended network will be your original network name plus
«_EXT» at the end. Now that your Wi-Fi network is extended, it gained a
password from your main router and became secure.
Press
AC1200 AC750
STEP 3
Relocate the Repeater
1 . For best performance, plug the repeater into an Outlet
halfway between the router and the WiFi dead zone.
The location you choose must be within the range of your
existing WiFi network.
2. Wait until the Signal LED turns solid blue. If not, relocate the repeater
closer to the router.
3. Connect your WiFi devices to the new extended network which is your
original network name plus «_EXT» at the end. Use the original password
from your main router for the password.
WiFi router
AC1200 AC750
Antennas upward and
vertical to the ground
Created for Smart Laziness
METHOD
EXTENDING YOUR WIFI NETWORK USING
REPEATER’S WEB-UI
STEP 1
Power on the Repeater
Plug the repeater into a power outlet
near the router in the same room.
Wait until the PWR LED turns solid
blue.
If you’re using a mobile device, ensure that the
Mobile Data function on your Wi-Fi device is
disabled during the setup process. If you are using
a computer, unplug the Ethernet cable if any. If your
computer is wirelessly connected, make sure that
you have connected to the repeater’s network.
AC1200 AC750
STEP 2
ExtendYour WiFi Network
1 . Connect your WiFi device to the repeater’s WiFi network
«NEXTBOX_2.4G_EXT» or «NEXTBOX_5.0G_EXT» (these will be
unsecured)
2. Start a web browser, enter http://re.nextbox.home or 192.168.0.254 in
the address bar to log into the repeater’s installation wizard. Create a
login and a password for later attempts (recommended). This password
will be later used to log into the repeater’s admin panel (not your WiFi
network)
Ensure that the Mobile Data
(if any) function Of your WiFi
device is disabled.
Created for Smart Laziness
3. Select your router’s WiFi network (SSID) that you want to extend.
4. Enter the original password of the WiFi network that you want to
extend (make sure to enter the exact password, otherwise the network
will not be extended). Additionally, in this step, you can also set your own
name for the network to be extended. Once entered, click the «Extend»
button below.
Wait a moment, the «Wireless network
extended successfully» page appears.
Your device will be disconnected from
the repeater’s network and the repeater
automatically reboots to finish the setup
process. Once rebooted and the Signal
LED is solid blue, you can connect to the
extended repeater’s network using your
network’s original password.
To log into the admin panel in the future,
only use the http://re.nextbox.home
address
AC1200 AC750
STEP 3
Relocate the Repeater
1 . For best performance, plug the repeater into an Outlet
halfway between the router and the WiFi dead zone.
The location you choose must be within the range of your
existing WiFi network.
2. Wait until the Signal LED turns solid blue. If not, relocate the repeater
closer to the router.
3. Connect your WiFi devices to the new extended network which is your
original network name plus «_EXT» at the end. Use the original password
from your main router for the password.
WiFi router
AC1200 AC750
Antennas upward and
vertical to the ground
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza