Ledlenser XP30R Manuale utente

XP30R

MANUAL

XP30R manual V.01_01.2023

Thank you

We are delighted that you have chosen one of

our products.

You will ﬁnd safety and operating instructions

in this instruction manual to make you familiar

with your new product.

It must be read carefully before using the

product. Please keep the User Manual in

a safe place and always hand it over if the

product is given to a third party.

The User Manual also helps you get the maxi-

mum use out of the product, provides answers

to your questions and helps to avoid incorrect

operation. Therefore, please particularly

follow the warnings and safety instructions

and dispose of the lamps, batteries as well as

packaging material properly.

Table of contents

1. General information

2. Delivery scope

3. Safety instructions

4. Changing batteries and charging

5. Basic functions

6. Boost function

7. Strobe function

8. Remote mode

9. Temperature monitoring

10. Battery management and backup mode

11. Stand-mounting

12. Fault diagnosis

13. Technical data of the lamp

14. Instructions regarding disposal

15. Other information

XP30R manual V.01_01.2023

1. General information

Product information

The Ledlenser XP30R is a searchlight and may

be used only for the purposes of illumination. The

lamp is also equipped with a light source that

cannot be replaced by the user.

Please register your lamp using the enclosed

registration card to get an extended guarantee, to

check the authenticity of the lamp, and to be able to

get innovations for product improvements.

Charger and battery are excluded from the guaran-

tees beyond the statutory warranty.

Information about this manual

Carefully read the manual before using the

lamp and follow all the safety instructions and

warnings.

The manual includes the following signs and

signal words:

• General list

‣Instructions for safety instructions and

warnings

1. Action / Step

⇢Result of an action

WARNING indicates a potentially hazardous

situation, which can lead to death or a severe

injury if not avoided.

CAUTION indicates a potentially hazardous

situation, which can lead to moderate or minor

injury if not avoided.

ATTENTION indicates a situation, which can lead

to material damage if not avoided.

XP30R manual V.01_01.2023

2. The delivery scope of this product includes:

• XP30R Searchlight

• Hard shell case

• Li-ion battery

• Charging station

• Carry strap

• Remote

• Universal mount

• Manual

• Registration card

The lamp may be used only with the following

rechargeable batteries (battery pack).

• Compatible rechargeable batteries supplied by

or ocially acquired from Ledlenser

Delivery scope

General safety instructions 3. Carefully read the following safety instructions

before using the product.

WARNING – Risk of injury

Keep the lamp out of the hands of children or

persons aected by medication, drugs, physical/

mental disabilities or illnesses because there is a

risk of an injury to the eyes as well as an accident.

‣Do not let children play with the lamp.

‣Persons with disabilities should use the lamp

only under the supervision or instructions of a

responsible persons.

CAUTION – Risk of injury

Do not use the lamp if it is damaged, do not repair,

open, or modify it since it can damage the lamp or

endanger persons.

‣Take damaged lamps out of operation or have

them repaired professionally.

XP30R manual V.01_01.2023

CAUTION – Risk of blinding by glare

The starting blinding eect of the lamp can

temporarily restrict the vision and cause afterim-

ages, which can lead to irritations, disabilities or

accidents.

‣Do not look directly into the light beam or shine

the beam in the eyes of others.

‣Do not direct the light beam on people/animals

‣Do not use the lamp under the inﬂuence

of drugs, medication, or alcohol since the

reactivity of the eyes and the capacity to act is

reduced.

‣If a light beam hits the eyes, close them and

turn the head away from the light beam.

CAUTION – Fire and risk of burns

The lamp is classiﬁed in risk group 2 (medium risk)

under the IEC 62471 standard and is thus beyond

the ‘Free Group’. There is a risk of retina damage due

to optical radiation (blue light 400nm to 780nm).

CAUTION – Fire and risk of burns

The lamp generates heat during use.

‣Do not operate the lamp unattended.

‣Do not cover the lamp during operation since

this can lead to a heat build-up.

‣Maintain a distances of at least 2 m between

the lamp and the ﬂammable surfaces.

‣Do not touch hot lamp, if required, let it cool

down.

‣Close the protective cover of the lamp during

transport and disable the remote operation so

that the lamp is not accidentally switched on.

ATTENTION – Damage to the lamp

Use the lamp

‣only at ambient temperatures of -20 °C to

+40 °C,

‣do not bring it in contact with salt water,

‣protect against intense heat and wet,

‣do not use or store with the battery cover open.

VWARNING – Risk of explosion / injurying

The batteries and button cells can explode due

to improper use, leaking battery acid can cause

chemical burns.

Do not store the batteries and button cells

‣within the reach of children,

‣protect against heat (e.g., sunlight), heat build-

up, wet, or dirt,

‣do not throw in a ﬁre,

‣do not use in explosive areas,

‣do not open, damage, or short circuit.

‣If not in use for a long time, remove the batter-

ies from the lamp and charge regularly only in

the charging station supplied (every 3 months).

Click

e) Hold

XP30R manual V.01_01.2023

ATTENTION – Damage to the batteries

Batteries may be charged only at temperatures of

10 °C to 40 °C, otherwise they can be damaged and

no longer work.

‣Charge the batteries only within the given tem-

perature limits.

4. IInserting the battery

1. Fold up the safety lever of the battery cover (Fig.

4a).

2. Fold down the battery cover (Fig. 4b).

3. Slide in the battery from above (Fig. 4c).

⇢The battery locks into the proper position

with an audible snap.

4. Close the battery cover.

Removing the battery

1. Fold up the safety cable of the battery cover

(Fig. 4a).

2. Fold down the battery cover (Fig. 4b).

3. Press the red locking button (Fig. 4d) on the bat-

tery and simultaneously pull up the battery and

out from the battery compartment (Fig. 4e).

4. Charge the battery or insert new battery (Fig. 4c).

5. Lift up the battery cover and close the safety

lever.

ATTENTION - Environmental protection

Defective batteries must be disposed of in accord-

ance with the country’s legislation, as they can be

dangerous for the environment.

In order to get more information regarding the

operation and safety of the battery and the charging

station, please scan the following QR code or visit

www.ledlenser.com:

Changing batteries and charging

f)e)

Hold

b)a)

Hold> 2s

XP30R manual V.01_01.2023

Basic functions 5. Switching on the lamp

1. Lift up the safety cover (Fig. 5a).

2. Brieﬂy press the main switch (Fig. 5b).

⇢The lamp starts in the operating mode,

which is preselected over the mode switch

button (refer chapter Mode Switch).

⇢The battery capacity display shows the

current charging state (Fig. 5c).

3. Close the safety cover.

Switching o the lamp

1. Lift up the safety cover (Fig. 5a).

2. Keep the main switch pressed (Fig. 5d) until the

bar display (Fig. 5c) goes out.

3. Close the safety cover.

Fixing the carry strap

Attach the two hooks of the carry strap (Fig. 5f) on

the two mounting brackets located on the upper

side of the product (Fig. 5e).

100%

90%

80%

70%

60%

50%

40%

30%

20%

10%

XP30R manual V.01_01.2023

Battery capacity display

If the lamp is switched on, the remaining battery

capacity is displayed via a 10-step LED bar display

(1 bar = 10%) on the upper side of the device (Fig.

5g).

Mode 1

Mode 0

Remote-Mode

O

Mode 2

Mode 3

Mode 4

Mode 5

Brightness setting

XP30R manual V.01_01.2023

Mode Switch

The mode switch button (Fig. 5 h) oers six switch

positions with which remote control (mode 0 –

remote mode, Fig. 5i) can be activated and ﬁve

dierent brightness levels (Fig. 5j) from mode 1

(weak) to mode 5 (strong) can be selected.

If the lamp is switched on and the mode switch is

in position 1 (mode 0, Fig. 5h/i), the lamp does not

light up since it is in remote mode.

Details for coupling with remote control and the

operating functions provided can be found in

Chapter 8.

c) Boost = 10s

2x Click

b)a)

1x Click

b)a)

Pos. 1

Blue Blink

XP30R manual V.01_01.2023

Strobe function

Boost function

Remote mode

6. In boost mode, the lamp lights up with the maxi-

mum brightness for 10 sec. The boost mode can

be activated only in the switched on state (but not

in strobe mode).

Boost function

1. Switch on the lamp as per Chapter 5.

2. Lift up the safety cover as required (Fig. 6a).

3. Brieﬂy press the main switch 2 times (Fig. 6b).

⇢The boost mode starts (Fig. 6c).

⇢After ten seconds, the lamp switches back

to the previous light function.

4. The boost mode can be stopped at any time by

brieﬂy pressing the main switch.

7. In strobe mode, the lamp emits quick ﬂashes with

changing frequency and thus generates a discon-

certing blinding eect for an emergency.

WARNING – Risk of injury

The strobe function of the lamp can have negative

eects on people with photosensitive epilepsy.

This can result in accidents and injuries.

‣Use the strobe mode only in an emergency and

in consultation.

Strobe function

1. Activate the strobe function in the switched on

state by pressing the switch behind the end of

the handle (Fig. 7).

⇢The switch locks.

2. End the strobe function again by pressing the

rear switch.

8. For the ﬁrst use of the remote control for light

control, the remote control must be linked with

the lamp.

Linking the lamp for the ﬁrst time

1. Lift up the safety cover (Fig. 8a).

2. Switch on the lamp by brieﬂy pressing the

main switch (Fig. 8b).

3. Switch the lamp to remote mode (position 1)

with the mode switch button (Fig. 8c).

⇢The blue status LED on the lamp blinks

(Fig. 8c), to signal that the lamp is ready for

linking with the remote control.

4. Within the next 10 sec, keep the + and –

buttons of the remote control simultaneously

pressed for 2 sec (Fig. 8d).

⇢Upon successful connection, the blue status

LED remains lit up.

Indice

Altri manuali ledlenser Attrezzatura di illuminazione

ledlenser

ledlenser P5R Core Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente

ledlenser XP30R Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche