LEGRAND Niky 1000 Manuale utente

Niky 1000/1500

Index

1 Introduction 14

2 Conditions of use 14

3 Installation 15

4 Signals and controls 15

5 Overload and self-shutdown 16

6 Features 16

7 Changing batteries 17

8 Possible malfunctioning 18

9 Technical features 19

1 Introduction

This manual contains information for users of the Niky 1000/1500 models.

You are advised to read this handbook carefully before installing your uninterruptible power sup-

ply, meticulously following the instructions given herein.

The UPS NIKY is only been made for civil or industrial use; it is not in conformity with the standards

for electro-medical equipment.

• The UPS NIKY has been designed to supply data processing equipment. The load applied must

not exceed the one indicated on the rear label of your UPS.

• The ON/OFF button of your UPS does not electrically isolate the internal parts. To isolate your

UPS unplug it from the mains power socket.

• Do not open the UPS container since there may be parts inside with dangerously high voltage

even when the mains plug is disconnected; there are no parts inside that the user can repair.

• The UPS NIKY has been designed to work in closed, clean rooms where there are no inflammable

liquids or corrosive substances and where it is not too damp.

• Do not place near equipments that generate strong electro-magnetic fields and/or near equi-

pments that are sensible to electro-magnetic fields. (engines, floppy disks, speakers, adapters,

monitors, video, etc...)

• Do not pour any liquid on the UPS or inside the UPS.

• Do not place the UPS in humid environment or near liquid, such as water, chemical solution…

• Do not expose the UPS to the direct sunlight or any heat sorces.

• Keep the ventilation slits clean to dissipate the heat of the UPS.

• Use grounded power cable to connect the UPS to the mains supply.

• Do not plug laser printers into the UPS because of their high start-up current.

• Do not plug house electric equipments, such as hair dryer,air conditioner, and refrigerator into

the UPS outlets.

2 Conditions of use

Niky 1000/1500

• Take your UPS out of its packing.

• Make sure the mains supply voltage is identical to the one indicated in the label placed on the

rear of the UPS.

• Switch on your UPS with the ON/OFF button and check it operates correctly with the mains

(green LED on).

• Switch the UPS off by pressing the ON/OFF button until the LED shuts down.

• After switching off the UPS, connect the load power cable to the UPS output using the outlet

located on the right side of the UPS.

• Switch on your UPS and then the load to check it operates correctly with the mains (green LED on).

• Keep the UPS on for 8 hours to recharge battery before using it.

• UPS can also be used before battery is completely charged, but in this case back up time availa-

ble during black out will be shorter.

LED indicators:

The different colours of the LEDs on the front panel indicate the following:

• LED1: Fixed green: mains present and regular.

Green flashing every 2 sec: batteries are recharging

• LED2: Fixed yellow: no mains (running on battery)

• LED3: Fixed red: overload alarm

• LED4: Red flashing every 0.5 sec: autonomy in reserve

Acoustic signals:

• Intermittent sound every 2 sec.: running on battery

• Intermittent sound every 0.5 sec: overload or autonomy in reserve

• Continuous sound: failure or generic alarm

3 Installation

4 Signals and controls

CAUTION

While wiring the outlet line, make sure the total length of the cable, from the UPS to the

farthest utility, does not exceed 10 metres.

NOTICE

Never disconnect the 230 V power plug while the UPS is operating since this would

disconnect the earthing protection both from the UPS and from the loads connected to it.

5 Overload and self-shutdown

Your UPS is equipped with a system to measure the power delivered at the outlet; when this ex-

ceeds the set thresholds, the protection and relative signals are activated; shutdown is automatic

with a delay in relation to the size of the overload.

Under the line mode the green led will be light. If the overload is 100% ± 10%; UPS will shutdown

after 5 minutes and go to fault mode. If the overload is 110% ± 10%; UPS will shutdown immedia-

tely and go to fault mode.

Under the battery mode the yellow led will be flashed. If the overload is 100% ± 10%; UPS will be

shutdown after 5 second and go to fault mode.

If the overload is 110% ± 10%; UPS will shutdown immediately and go to fault mode.

Self test

Automatic self text is executed each time the UPS is switched on, to provide a reliable operation.

Battery Protection

Automatic battery test and deep discharge protection.

DC start capability

The UPS can be switched on in DC mode (battery operation) rete provided the load does not

exceed 80% of the UPS’rated power.

UPS power supplied outlets

This is a line interactive UPS equipped with AVR, that allows to feed the load with a stabilized

output voltage even when mains floats.

Electrical protection

Automatic swith off upon short circuit.

Full time surge protection outlet

Connect the appliances not needing for back up protection (printers, fax etc.) to the surge

protected outlet located near the back of the unit.

EMI/RFI filtering:

Bad quality of mains supply can damage electronic appliances because of electromagnetic radio

frequency interferences.

The UPS is provided with a dedicated filter to eliminat these disturbances.

6 Features

Niky 1000/1500

Software connection Niky 1000/1500

The UPS is equipped with a RS232 interface (DB9 cable for software communication is needed)

and USB interface, thanks to which it is possible by means of a computer to access a set of data

regarding the operation of the UPS and control the operating system unattended shutdown.

Software is available as on option for Win98/ME/2000, Novell and Linux, from the website

www.ups.legrand.com without charge. User license is included in the product.

Telephone protection

The NIKY UPS has an integrated, standard RJ11/RJ45 passing telephone connectionthat provides

protection for telephone or network equipment (modem, telephones, etc.) against overvoltage.

6 Features

Caution

Opening, repairing, or replacing parts inside the UPS must always be carried out by specialized

technical personnel only. First of all, switch off the UPS with the ON/OFF button located on the

front panel, then unplug the power cable from the 230V outlet socket.

1) Switch off the uninterruptible power supply.

2) Unplug the power cable from the mains socket.

3) Change the batteries with others of the same type and make, or having the same features

Keep clear from fire to avoid explosion while handling batteries.

Do not open or tamper with the battery case, because it contains toxic electrolyte that could be

harmful for your skin or eyes. Keep out of children’s reach.

7 Changing batteries

NOTICE

The batteries must only be replaced by qualified technical personnel, who will dispose of

them in compliance with the law in force.

8 Possible malfunctioning

The UPS always operates on batteries:

• There is no line voltage

• Line voltage is out of allowed UPS range

• The power supply cable is not correctly connected to mains socket.

• The input circuit breaker has to be reset

• The mains socket is defective

The UPS signals overloading:

• Additional loads to the ones normally connected have involuntarily been connected on the

output line.

• Check all the loads connected to the output

The UPS doesn’t operate in battery mode (it shuts down or immediately signals it is close to the

operating limit):

• The UPS has operated with no mains voltage for a long time and has not been able to recharge

the battery. Recharge it for at least 6 hours by connecting the uninterruptible power supply to

the mains.

• The battery is flat due to not using the UPS for a long period. Recharge it for at least 6 hours by

connecting the uninterruptible power supply to the mains.

• The battery has run down due to being used frequently, to ambient conditions, or to having

exceeded its average service life; it is necessary to change it.

The UPS doesn’t deliver power to the output:

• Check that the loads are correctly connected to the output sockets

Niky 1000/1500

9 Technical features

CONSTRUCTION SPECIFICATIONS

3 100 04

3 100 13

3 100 26

3 100 05

3 100 14

3 100 27

Weights 13 Kg. 16 Kg.

Dimensions L x H x P in mm 147 x 239 x 354

Protection

Electronic protection against overloading

and short-circuiting. Shutdown on

reaching operating limit and overheating.

Automatic shutdown due to protection

triggering

Ambient specifications

Operating temperature range from 0 to +40 °C

Operating relative humidity range from 0 to 95% non-condensing

Degree of protection as per IEC529 IP20

Noise level at 1 meter < 40 dBA

Electrical input specifications

Rated input voltage 230 V

Range of input voltage 175-285VAC

Rated input frequency 50-60 Hz +/-5Hz

Maximum input current 6,2 Arms 8,5 Arms

Number of input phases Single phase

Waveform on output

With battery operation step wave

Type of operation line interactive

Electrical specifications on output

Rated output voltage 230 V ± 10 %

Output current on nominal load 4,7 Arms 6,5 Arms

Apparent output capacity on nominal load 600 W 900 W

Apparent output capacity on nominal load 1000 VA 1500 VA

Overload capacity 110% for 5 s.

Number of phases on output Single phase

9 Technical features

NOTICE

The batteries are considered hazardous waste and should be disposed of in accordance with

current regulations.

CONSTRUCTION SPECIFICATIONS

3 100 04

3 100 13

3 100 26

3 100 05

3 100 14

3 100 27

Electrical specifications on output with battery operation

Rated output voltage 230 V ± 10 %

Output frequency 50/60 Hz ± 1Hz

Active output capacity on non-linear load 600 W 900 W

Apparent output capacity on non-linear load 1100 VA 1500 VA

Battery operation

Operating time to 80% of the load 5 min. 5 min.

Charging time 10/12 h at the end of operating range

Technical data and number of batteries

n° 2

maintenancefree,

sealed, leadacid

batteries 12V

7,2 Ah

n°2

maintenance-free,

sealed, lead-acid

battery 12V

9 Ah

Standards

Electromagnetic compatibility

Emission - Immunity Conforms to EN 62040 - 2

Safety Conforms to EN 62040 -1 -1

Performance and features Conforms to EN 62040 -3

Niky 1000/1500

9 Technical features

1 Status Leds

2 Power Switch

3 Telephone, fax, modem or network protection

4 Output sockets

5 AC Input with AC Fuse

6 USB Serial Interface

7 RS232 Serial Interface

3 100 13

3 100 14

112

76 3

5 5

76 3

3 100 04

3 100 05

4 4

76 3

3 100 26

3 100 27

Altri manuali per Niky 1000

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LEGRAND UPS

LEGRAND

LEGRAND Daker DK 1 kVA Manuale utente

LEGRAND

LEGRAND DAKER DK Plus 3 101 73 Manuale utente

LEGRAND

LEGRAND NUMERIC Valura 1-3 kVA IBB Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

LEGRAND

LEGRAND KEOR MULTIPLUG 600 Manuale utente

LEGRAND

LEGRAND KEOR SPE R/T Manuale utente

LEGRAND

LEGRAND 678 135 Manuale utente

LEGRAND

LEGRAND WHAD HE 3 101 67 Manuale

LEGRAND

LEGRAND Seismic Kit Trimod HE Manuale utente

LEGRAND

LEGRAND KEOR HP 60kVA Manuale utente

LEGRAND

LEGRAND KEOR T 208V 40 KVA Manuale utente

LEGRAND

LEGRAND KEOR HP Series Manuale di installazione

LEGRAND

LEGRAND KEOR LP Manuale utente

LEGRAND

LEGRAND 3 108 43 Manuale utente

LEGRAND

LEGRAND Keor SPE 750 Manuale utente

LEGRAND

LEGRAND KEOR MOD Manuale utente

LEGRAND

LEGRAND NUMERIC Onfiniti Manuale operativo

LEGRAND

LEGRAND KEOR S 3KVA 1 Manuale

LEGRAND

LEGRAND MIDDLE ATLANTIC NEXSYS Manuale utente

LEGRAND

LEGRAND Whad 0.8 kVA Manuale utente

LEGRAND

LEGRAND NUMERIC HP i 33 40 kVA Series Manuale utente

LEGRAND

LEGRAND Megaline Series Manuale utente

LEGRAND

LEGRAND KEOR MULTIPLUG Manuale utente

LEGRAND

LEGRAND 430 557 Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente

ZincFive

ZincFive BC Series Manuale utente