Lennox RG10F2-MMA Manuale utente

INSTALLATION AND USER

INFORMATION GUIDE

Dallas, Texas, USA

CAUTION

As with any mechanical equipment,

contact with sharp sheet metal edges

can result in personal injury. Use caution

while handling this equipment. Wear

gloves and protective clothing.

IMPORTANT

Frequent changes to operating mode

may cause system malfunctions. Allow

at least one minute between mode

changes to allow the system to stabilize.

Shipping and Packing List

Package 1 of 1 contains:

1 – Wireless Controller

2 – AAA batteries

1 – Remote controller holder with

mounting screw

Lennox Mini-Split Systems

Indoor Wireless

Programmable Controller

(RG10F2-MMA)

CONTROLS

508415-01 9/2023

This manual must be left with the owner

for future reference.

Table of Contents

General...................................................2

Requirements .........................................2

Remote Controller Specications ...........2

Handling the Remote Controller .............2

Inserting and Replacing Batteries...... 2

Battery Disposal................................. 3

Remote Controller Tips ...................... 3

FCC Compliance Statement .............. 3

Buttons and Functions............................4

Screen Icons...........................................5

Basic Functions ......................................6

Setting the Temperature..................... 6

AUTO Mode ....................................... 6

COOL Mode....................................... 6

DRY Mode ......................................... 7

HEAT Mode........................................ 7

FAN Mode .......................................... 8

Setting the TIMER.............................. 8

Advanced Functions...............................9

General

The RG10F2-MMA is a wireless

programmable controller for the MLB/

MPC outdoor units with MMA indoor

units. It is capable of executing timed

schedules for daily operation. These

instructions are intended as a general

guide and do not supersede local codes

in any way. Consult authorities having

jurisdiction before installation.

Requirements

Verify the power supply has been

turned o󰀨 before beginning installation.

This controller should be used only as

described in this manual.

Do not install the controller on exterior

walls (where there is unconditioned

space on opposite side of wall) or in

locations where direct sunlight may be

present.

Remote Controller Specications

Model RG10F2-MMA

Rated Voltage 3.0V

(Dry batteries, AAA)

Signal Receiving

Range

26 feet (8 meters)

Environment 23°F~140°F

(-5°C~60°C)

Handling the Remote Controller

Inserting and Replacing Batteries

1. Slide the back cover on the remote

controller downward, exposing the

battery compartment.

2. Insert the batteries; match the (+)

and (-) ends of the batteries with

the symbols inside the battery

compartment.

3. Slide the battery cover back into

place.

Figure 1. Removing Battery Cover

NOTE: For optimum product

performance: Do not mix old

and new batteries, or batteries

of dierent types. Do not

leave batteries in the remote

controller if it will not be used

for more than two months.

Battery Disposal

Do not dispose of batteries as unsorted

municipal waste. Refer to local laws for

proper disposal of batteries.

Remote Controller Tips

• The remote controller must be used

within 26 feet (8 meters) of the unit.

• The unit beeps when remote signal is

received.

• Curtains, other materials, and direct

sunlight can interfere with the infrared

signal receiver.

• Remove batteries from the remote

controller if it will not be used for more

than two months.

FCC Compliance Statement

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful

interference.

2. This device must accept any

interference received, including

interference that may cause

undesired operation.

NOTE: This equipment has been tested

and found to comply with the

limits for a Class A digital device,

pursuant to Part 15 of the FCC

Rules. These limits are designed

to provide reasonable protection

against harmful interference

when the equipment is operated

in a commercial environment.

This equipment generates, uses,

and can radiate radio frequency

energy, and if it is not installed

and used in accordance with the

instruction manual, it may cause

harmful interference to radio

communications.

Operation of this equipment in a

residential area is likely to cause

harmful interference, in which

case the user will be required to

correct the interference at their

own expense.

MODIFICATIONS:

Any modications made to this

device that are not approved by

Lennox International may void

the authority granted to the user

by the FCC to operate this equip-

ment.

The following is a brief overview of the remote controller. For instructions on how to

operate the unit, see “Basic Functions” on page 6 of this manual.

Figure 2. Controller Buttons and Functions

ON/OFF

Turns the unit on or o󰀨.

TEMP

Increases temperature in 1°F (1°C)

increments. Max. temperature is 86°F

(30°C). Also used to set the Timer On/

Timer O󰀨 functions.

TEMP

Decreases temperature in 1°F (1°C)

increments. Max. temperature is

60°F (16°C). Also used to set the

Timer On/Timer O󰀨 functions.

TIMER ON

Sets timer to turn unit on

(see How to Use Basic

Function for instructions).

TIMER OFF

Sets timer to turn unit o󰀨

(see How to Use Basic

Function for instructions).

MODE

Scrolls through operation modes as

follows: AUTO → COOL → DRY →

HEAT → FAN.

SWING

Not available.

Used to conrm the

selected functions.

FAN SPEED

Selects fan speeds in fthe

following order AUTO →

LOW → MED → HIGH.

SHORTCUT

Used to restore the current

settings or resume previous

settings.

°C/°F

The temperature display

between the °C & °F.

SLEEP

Saves energy during sleep

hours.

LED

Not available.

Buttons and Functions

LOCK

Press to disable the button

functions of the controller.

SET

Scroll to locate

I SENSE ( ) function. Press the

OK button to conrm. Fresh and

AP mode are not functional with

this unit.

Screen Icons

Transmission Indicator

MODE

TIMER ON

FAN SPEED

TIMER OFF

LOCK

Not available for

this unit

Temperature/Timer/Fan speed

Not applicable for this unit

Sleep mode icon

I Sense icon

Not applicable for this unit

Low battery detection display

(If flashes)

Displays when LOCK feature

is activated.

Lights up when remote

sends signal to indoor

unit Displays the current

including:

mode,

Displays the set temperature

by default, or fan speed or

timer setting when using

TIMER ON/OFF functions.

Temperature range:

16-30 C/60-86 F

Timer setting range:

0-24 hours

This display is blank when

operating in FAN mode.

Not applicable

for this unit.

LOW

MED

HIGH

AUTO

Displays selected fan speed:

This fan speed can not be

adjusted in AUTO or DRY

mode.

Note:

All icons are shown for display purposes only.

During actual unit operation, only active icons are displayed.

The following icons display after powering up the remote controller.

NOTE: All icons shown in Figure 3 are for display purposes only.

Only active icons display during unit operation.

Figure 3. Remote Controller Screen Icons

Basic Functions

Before operation, verify the unit is powered

up.

Setting the Temperature

The operating temperature range for units

is 60-86°F (16-30°C).

Users can increase or decrease the set

temperature in 1°F (1°C) increments.

AUTO Mode

In AUTO mode, the unit will automatically

select the COOL, FAN, or HEAT function

based on the set temperature.

1. Press the MODE button to select

AUTO.

2. Set the target temperature using the

TEMP or TEMP button.

3. Press the ON/OFF button to start the

unit.

NOTE: FAN SPEED cannot be set in

AUTO mode.

COOL Mode

1. Press the MODE button to select

COOL mode.

2. Set the target temperature using the

TEMP or TEMP button.

3. Press FAN button to select the fan

speed: AUTO, LOW, MED, HIGH.

4. Press the ON/OFF button to start the

unit.

DRY Mode

1. Press the MODE button to select

D R Y.

2. Set the target temperature using the

TEMP or TEMP button.

3. Press the ON/OFF button to start the

unit. FAN SPEED cannot be changed

in DRY mode.

HEAT Mode

1. Press the MODE button to select

HEAT mode.

2. Set the target temperature using the

TEMP or TEMP button.

3. Press FAN button to select the fan

speed: AUTO, LOW, MED, HIGH

4. Press the ON/OFF button to start the

unit.

NOTE: As outdoor temperature drops,

the performance of the unit’s

HEAT function may be aected.

In such instances, Lennox

recommends using this unit in

conjunction with other heating

appliances.

FAN Mode

1. Press the MODE button to select FAN

mode.

2. Press FAN button to select the fan

speed: AUTO, LOW, MED, HIGH.

3. Press the ON/OFF button to start the unit.

NOTE: The temperature can not be

set while in FAN mode. As a

result, your remote controller’s

LCD screen will not display

temperature.

Setting the TIMER

TIMER ON

1. Press TIMER ON to initiate the ON

time sequence.

2. Press the TEMP or TEMP

button to set the start time for the unit.

3. Point the remote controller toward the

unit and wait for one second.

The TIMER ON function is set.

TIMER OFF

1. Press TIMER OFF to initiate the OFF

time sequence.

2. Press the TEMP or TEMP

button to set the end time for the unit.

3. Point the remote controller toward the

unit and wait for one second.

The TIMER OFF function is set.

NOTE: When setting the TIMER

ON or TIMER OFF, the time

will increase by 30 minutes

increments with each press, up

to 10 hours. After 10 hours and

up to 24 hours, it will increase in

1 hour increments. (For example,

press 5 times to get 2.5h, and

press 10 times to get 5h. The

timer will revert to 0.0 after 24.)

Cancel either function by setting

its timer to 0.0h.

To Cancel TIMER ON/TIMER OFF

Cancel either function by setting the timer

to 0.0h.

• SWING

Not applicable for this unit.

• SHORTCUT

Press Shortcut and the system

automatically reverts to the previous

settings (including Operating Mode,

Setting Temperature, Fan Speed Lev-

el, and Sleep Feature, if set).

NOTE: If the Shortcut button is pressed

for longer than two seconds, the

system automatically restores the

current operation settings.

• °C/°F

Press °C/°F to alternate the tem-

perature display between celcius and

farenheit.

• LED Display

Press the LED button to turn on and

o󰀨 the LED display on the indoor unit.

• SLEEP

Press the Sleep button to decrease

the unit’s energy usage. This function

is benecial for users who do not

require the same temperature settings

to stay comfortable while sleeping.

Only the remote controller can acti-

vate the Sleep function.

NOTE: The Sleep function is not

available in FAN or DRY mode.

• LOCK

Press LED and °C/°F simultaneously

for ve seconds to activate the Lock

function. Once locked, all buttons lose

functionality. To restore functionality,

press LED and °C/°F simultaneously

for two seconds.

• SET

Press the SET button to enter the

function setting. Press SET, TEMP

or TEMP to select the target func-

tion. The selected symbol will ash on

the display area, press the OK button

to conrm.

To cancel the selected function, press

SET, TEMP or TEMP to locate

the function to cancel. After locating

the system function, press OK to

cancel it.

• I SENSE

Enables the remote controller to

measure the temperature at its

current location and send this signal

to the unit every three minutes. When

using AUTO, COOL or HEAT modes,

measuring ambient temperature from

the remote controller (instead of from

the indoor unit itself) enables the unit

to optimize the temperature to ensure

maximum comfort.

Advanced Functions

Indice

Altri manuali Lennox Controllori

Lennox

Lennox M0STAT64Q-2 Istruzioni per l'installazione

Lennox

Lennox V0STAT54P-2 Istruzioni per l'installazione

Lennox

Lennox V0STAT52 Manuale utente

Lennox

Lennox V0STAT54P-2 Manuale utente

Lennox

Lennox PRODIGY2.0 Guida utente

Lennox

Lennox VRF VEWCL1E Manuale utente

Lennox

Lennox PRODIGY M2 Guida utente

Lennox

Lennox M0STAT64Q-1 Istruzioni per l'installazione

Lennox

Lennox Core Unit Controller Manuale utente

Lennox

Lennox 20 Guida utente

Lennox

Lennox icomfort Wi-Fi (2.0) Demo Manuale utente

Lennox

Lennox CLIMATIC series Manuale utente

Lennox

Lennox DC 60 Manuale utente

Lennox

Lennox V0STAT51P-3 Istruzioni per l'installazione

Lennox

Lennox V0STAT51P-2 Manuale utente

Lennox

Lennox e-Lite LV-CW02 Manuale utente

Lennox

Lennox M0STAT60Q-1 Manuale utente

Lennox

Lennox Wired Controller Manuale utente

Lennox

Lennox LXTFF01M Manuale utente

Lennox

Lennox @DNOVA 2mAC ADVANCED CONTROLLER Manuale utente

Lennox

Lennox Prodigy Manuale utente

Lennox

Lennox 22U50 Manuale utente

Lennox

Lennox @DNOVA pCO1 Manuale utente

Lennox

Lennox F1943L-3P Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente