NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE 3
Fully Open or
Fully Closed
Front-Open Systems
CLEANING
NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. DO NOT USE
AMMONIAORANYAMMONIABASEDGLASSORHOUSEHOLDCLEANER
TO CLEAN THE GLASS OR THE DOOR FRAME. AN AMMONIA BASED
CLEANER WILL DAMAGE THE FINISH.
Remove dirt and grime from the doors using a clean dampened towel
followed by wiping with a dry towel. To remove stubborn stains from the
doors, use a mild soap solution and towel to gently scrub away stain.
Take care not to scratch the glass surface. Do not use abrasive cleaners.
IMPORTANT
These glass doors utilize tempered glass which is designed for use
with high temperatures but can unexpectedly shatter. DO NOT SIT
CLOSE TO THE GLASS.
Tempered glass will break into small particles if it should shatter
unexpectedly. If the glass breaks, particles of extremely hot glass could
be discharged into the surrounding environment, thereby creating a risk
ofpersonal injuryor fire.Observationoftheaboveoperatingprecautions
and instructions will reduce the risk of personal injury or fire.
Extreme temperature changes can cause breakage — do not build a hot
fire and close the doors if the doors are cold.
If the tempered glass pane becomes scratched or chipped, it creates a
weakness in the glass which can cause the glass to break when heated.
Replace the pane of glass by contacting your nearest distributor. For the
name of your nearest distributor contact:
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
Figure 4
WARNING:DO NOT BURNTRASH, CONSTRUCTION SCRAPS,
RAILROAD TIES, OR OTHER HIGHLY-FLAMMABLE MATE-
RIAL IN THE FIREPLACE. INTENSE HEAT CAN CAUSE THE
GLASS TO LOSE STRENGTH AND RESILIENCE WHICH WILL
RESULT IN GLASS BREAKAGE.
ADJUSTMENT FOR DOOR ALIGNMENT
The doors are properly adjusted when the top door trim is in a straight,
level line and the gap between the doors and the frame is even at the top
and bottom. The doors can be adjusted by changing the location of the
door inside the frame. The door may need adjustment for several
reasons. One would be that the doors do not fully close because they hit
in the center of frame. Another would be that there is a noticeable gap
in the center between the closed doors.
If doors appear to close in correct position but do not latch (both doors
do not stay closed), then there is a misalignment between the doors and
the Center Wedge Clip. The Center Wedge Clip is located in the center
ofthebottomTrack. In order to stay closed,theleftandright doors must
meet in the Middle of the Center Wedge Clip.
To adjust doors, first loosen, but DO NOT remove the Phillips Screw that
holds the Retainer Clip to the frame. Move door to desired position then
tighten screw. Repeat procedure for other Retainer Clips as needed.
Operate doors to check alignment and repeat procedure if necessary.
GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS
CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH
THE LENNOX FIREPLACE OR APPLIANCE MODELS SHOWN. USE ON
ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTITUTE A POTEN-
TIAL FIRE HAZARD.
•Avoid building extremely large fires as the tempered glass could
become damaged.
•Use fireplace tools carefully to avoid striking the glass.
•Keep wire mesh screens closed during fireplace use.
•The fireplace flue damper must remain open until fire is completely
out.
•Assure wood and embers are well within the confines of the grate area
and well away from the glass doors.
•Keep wire mesh screens closed during fireplace use.
•Keep glass doors closed at night when retiring to minimize the loss of
heated room air up the vent.
CAUTION: THE FRONT-OPEN FIREPLACE OR APPLIANCE SHOULD
ONLYBE OPERATEDWITHTHE GLASSDOORSFULLY OPENORFULLY
CLOSED (
SEE FIGURE 4
).
CAUTION: GLASS AND METAL FRAMES GET HOT — ALWAYS USE
HANDLES TO OPEN AND CLOSE THE DOORS.
To remove the doors, open door all the way until glass panes are back
toback. Whilepushingdownondoor, push up on Top Retainer Clip with
finger to free Top Pin and rotate top of door toward center of frame.
Carefully remove door.
