Leonton PG5-0802-M-24 Series Manuale utente

LEONTON

PG5-0802-M-24 Series

(PG5-0802-M-24 / PG5-0802-M-24-T)

User Manual

This document contains information, which is protected by copyright. Reproduction, adaptation or

translation without prior permission is prohibited, except as allowed under the copyright laws.

Disclaimer

LEONTON Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or

implied, including but not limited to the implied warranties of merchantability and fitness for a

particular purpose. LEONTON Technologies, Co. Ltd. may make improvements and/or changes to

the product and/or specifications of the product described in this manual, without prior notice.

LEONTON Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical

errors found in this guide. Changes are periodically made to the information contained herein and

will be incorporated into later versions of the manual. The information contained is subject to

change without prior notice.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class-A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy. It may cause harmful interference to radio communications if the

equipment is not installed and used in accordance with the instructions. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could

void the user's authority to operate the equipment.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

This document is the current official release manual. Please check our website (www.leonton.com)

for any updated manual or contact us by e-mail (sales@leonton.com).

Contents

Overview...................................................................................................................... 1

Software Features ................................................................................................. 1

Hardware Features ................................................................................................ 1

Package Contents .................................................................................................. 2

Safety Precaution ..................................................................................................2

Hardware Description ..................................................................................................4

Physical Dimensions .............................................................................................. 4

Front Panel............................................................................................................ 5

Top View................................................................................................................ 5

LED Indicators........................................................................................................5

Ethernet Ports ....................................................................................................... 7

Cabling .................................................................................................................. 8

Wiring the Power Inputs........................................................................................ 8

Wiring the Fault Alarm Contact .............................................................................9

Grounding Note................................................................................................... 10

Mounting Installation................................................................................................. 11

DIN-Rail Mounting............................................................................................... 11

Wall Mounting..................................................................................................... 13

Hardware Installation................................................................................................. 14

Installation Steps ................................................................................................. 14

Maintenance and Service........................................................................................... 15

Trouble Shooting........................................................................................................ 16

Overview

This series is rated IP30 and installation by DIN Rail. Each unit of this industrial gigabit managed

Ethernet switch series has 6 IEEE 802.3at compliant ports (30W/port) and 2 ports 1000x of SC or

ST type connector and support Multi-mode or Single-mode.

In order to prevent unregulated voltage, this series provides high EFT and ESD protection. This

also allows it to function in harsh environments, as well as support power redundancy with a dual

power input design with reverse polarity protection. The built-in relay warning function alerts

users about occurring power failures.

With one model having an operating temperature of -10 to 65°C, and another with a wide

operating temperature of -40 to 75°C, this series is designed to meet any needs for industrial

automation, outdoor application and harsh environments.

Software Features

Layer 3 Switching Static Routes

Management

CLI, Http, Https, SNMP, SSH, Telnet

Security

Access Management, ACL, ARP Inspection, DHCP Snooping, IP Source

Guard, Multiuser Account, Port Security Limit Control, RADIUS,

TACACS+, 802.1Q VLAN, IP Subnet-based VLAN, MAC-based VLAN,

Private VLAN, Protocol-based VLAN, GVRP

Green Ethernet

IEEE 802.3az EEE (Energy Efficient Ethernet)

Network Reliability STP, RSTP, MSTP, ERPS (G.8032)

Multicast

IGMP snooping, MLD snooping, MVR

Traffic Control LACP, QoS (CoS/To S)

Monitor

LLDP, LLDP-MED, Port Mirroring, RMON, MIB, sFlow, Syslog Server

DHCP DHCP Server/Client/Relay/Snooping

Other

ICMP Ping, ICMPv6 Ping, Loop Protection, Storm Protection, NTP Client

PoE Management

(For PoE Models) PoE Alive Check, PoE Power Budget Managed, PoE Scheduled

Hardware Features

Interface & Performance

•All Copper ports support auto MDI/MDI-X function

•Embedded 6*10/100/1000Tx (PSE 30W/Port) and 2*1000x SC/ST type connector

•Store-and-forward switching architecture

•8K MAC Address Table

•Supports 9.6Kbytes Jumbo Frame

•4Mbits memory buffer

Power Input

●Redundant power DC 12~55V with connective 1*6-pin removable terminal block

●Max. current: 10A

●Max. PoE output: 90W@12VDC / 180W@48-55VDC

●Relay Contact: 24 VDC, 1A resistive

●The power input specification is complied with the requirements of SELV (Safety Extra Low

Voltage), and the power supply should be complied with UL 61010-1 & UL 61010-2-201

Certification

•CE/FCC

•UL 61010-1

•UL 61010-2-201

Operating Temperature

•Standard operating temperature model: -10°C ~ 65°C

•Extended operating temperature model (–T): -40°C ~ 75°C

Case/Installation

•IP-30 protection

•Installation in a Pollution Degree 2 industrial environment

•DIN-Rail and wall mount design

Package Contents

•1 - PG5-0802-M-24(-T) product

•2 - Wall mounting brackets and screws

•1 - RJ45 to DB9 Serial Console cable

Safety Precaution

Attention

If the DC voltage is supplied by an external circuit, please use a protection device on the power

supply input. The industrial Ethernet switch’s hardware specs, ports, cabling information, and

wiring installation will be described within this user manual.

Warning Labels

The caution label means that you should check the certain information on user manual when

working with the device. (Shown in Figure 1.1)

Figure 1.1: Caution Label

This warning label is on the device, and means that the surface of the device is hot. (Shown

in Figure 1.2)

Figure 1.2: Hot Surface Warning Label

Hardware Description

Physical Dimensions

Figure 2.1, below, shows the physical dimensions of PG5-0802-M-24 series.

(W x D x H) is 54mm x 99mm x 142mm

Figure 2.1: PG5-0802-M-24 Series Physical Dimensions

Front Panel

The front panel of the PG5-0802-M-24 series industrial Gigabit managed Ethernet switch is

shown below in Figure 2.2.

Figure 2.2: The Front Panel of PG5-0802-M-24 Series

Top View

Figure 2.3, below, shows the top panel of the PG5-0802-M-24 series switch that is equipped

with one 6-pin removal terminal block connector for dual DC power inputs (12~55VDC).

Figure 2.3: Top Panel View of PG5-0802-M-24 Series

LED Indicators

There are LED light indicators located on the front panel of the industrial Ethernet switch that

display the power status and network status. Each LED indicator has a different color and has

its own specific meaning, see below in Table 2.4.

LED Color Description

P1 Green

On Power input 1 is active

Off Power input 1 is inactive

P2 Green

On Power input 2 is active

Off Power input 2 is inactive

FAULT

Green On No event happened

Red Off 1. Power input 1 or 2 is inactive

2. Port link-down/Broken

MASTER Green

On ERPS Owner Mode (Ring Master) is ready

Off ERPS Owner Mode is not active

RING Green

On ERPS Ring Network is active and works well

Flashing ERPS Ring works abnormally or misconfigure

Off ERPS Ring Network is not active

L/A

(Fiber Port 7-8) Green

On Connected to network, 1000Mbps

Flashing Networking is active

Off Not connected to network

(LAN Port 1-6)

Green

On Connected to network, 10/100/1000Mbps

Flashing Networking is active

Off Not connected to network

PoE

(LAN Port 1-6)

Green

On Supplying power to the powered-device

Off Not connected to a Powered Device

Table 2.4: LED Indictors for PG5-0802-M-24 Series

Caution:"P1/P2" is the abbreviation for "Power 1/Power 2", "L" is for "Link", and "A" is for

"Activity", “GE” is for “Gigabit Ethernet Port”.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Leonton Router di rete

Leonton

Leonton ET5-0802-M Series Manuale utente

Leonton

Leonton PT2-0800-24 Manuale utente

Leonton

Leonton EG2-0702-SFP Series Manuale utente

Leonton

Leonton PG5-0501-SFP-24 Series Manuale utente

Leonton

Leonton ET2-1600 Series Manuale utente

Leonton

Leonton ET5-0800 Series Manuale utente

Leonton

Leonton PG5-1600 Series Manuale utente

Leonton

Leonton PG2-1002-SFP Series Manuale utente

Leonton

Leonton EG2-0800 Series Manuale utente

Leonton

Leonton PT5-0501-M-24 Series Manuale utente

Leonton

Leonton CET2-0500 Series Manuale utente

Leonton

Leonton ET2-0500-M12-67 Series Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza