Leotek GreenCobra Manuale utente
Page 1 of 3
© 2020 Leotek Electronics USA LLC. GC_CV_EC_Installaon Guide_09-03-2020.
Step 3 Loosen the slip-er bracket bolts and insert the mounng arm. The maximum outside diameter for the mounng
arm is 2-3/8” (60.3mm). The minimum outside diameter for the mounng arm is 1-5/8” (41.28mm). Mounng arm to be
placed “stopped” against appropriate step required to achieve desired degree of lt. Steps vary from from 0o to get no lt
to the opons shown below.
This procedure is designed as an installaon aid. Skilled tradespeople that are familiar with general construcon and electrical installaon
techniques should perform the installaon. Licensed electricians should provide electrical installaon connecons. Installaons and
connecons should be done in accordance with all naonal and local codes and permits. In no way is this document intended to construe
warranty or tness of use of the products described, nor is it intended to provide safety instrucon for those installing the product.
WARNING
Before proceeding with installaon or service maintenance of this product:
• Disconnect power to reduce electrical shock risk.
• Review the enre Installaon Guide.
• Inspect this properly packaged product for any damage that may have occurred during transit.
• Verify product applicaon complies with manufacturer design recommendaons.
• Verify the availability of necessary tools and incidental material.
• Verify applicable code requirements. Field assembly and installaon are subject to acceptance by local inspecon authority.
• Appropriate safety equipment to be determined by end user, per applicable safety standards and precauons.
GreenCobra™ ComfortView™& E-Cobra™
LED Street Light Installaon Guide
Step 1 - Unfasten the power door latches. User-friendly
latches will vary depending on product model.
Luminaire Installaon
Step 2 - Open the door. Power door can be
securely hung or easily removed.
OR
,,
Complete product documentaon
available online at:
hps://leotek.com/lighng-library/
Page 2 of 3
© 2020 Leotek Electronics USA LLC. GC_CV_EC_Installaon Guide_09-03-2020.
GreenCobra™ ComfortView™& E-Cobra™LED Street Light
Installaon Guide
1
24
3
Step 5 - Adjust Drive Current/Light Output
Drive current should comply with designed illuminaon levels and circuit
loading. Consult with design engineer before changing. If a new drive current
or output code is required, open the connector and change the connecon
according to the current selector or output selector label installed in the xture.
Note: If the Fixed Drive Current (Fixed Output Code in J-Series) opon or Control
Ready opon was ordered, the drive current or the light output cannot be
changed. For ComfortViewTM product, an output selector is used to adjust the
illuminaon levels and circuit loading. Please refer to ComfortViewTM spec sheet
for specic details.
Electrical Wiring Connecon
Step 6 - Connect the green conductor to the ground chassis marked “G”(shown to the right of the terminal block).
Step 7 - Connect the black conductor (Hot 1) to the input terminal marked “L”.
Step 8 - Connect the white conductor (Neutral) or second black conductor (Hot 2) to the input terminal marked “N”
according to Wiring Table.
Step 9 - Close the door.
Wiring Table
MV*
(120/220/277V)
HV*
(347/480V)
LHot 1 Hot 1
NNeutral
Hot 2 (208V/240V) Hot 2
GGround Ground
LO (If Available) Not Used for Input Voltage
* All Power Supplies are Auto-Sensing
Step 4 - Securely ghten bolts to 16±2lbs-. (22Nm ± 3Nm) by alternang from bolt to bolt in equal measured amounts of 25%
torque. (See image below for ghtening order) Ensure that the slip-er bracket does not lt completely to one side and refrain
from unevenly ghtening bolts, as it will cause cross-threading.
Step 10 - If luminaire is furnished with photocontrol receptacle,
install the photo control or shorng cap.
WARNING: Avoid ghtening bolts unevenly, as it may cause cross-threading.
,
Page 3 of 3
© 2020 Leotek Electronics USA LLC. GC_CV_EC_Installaon Guide_09-03-2020.
12”
15”
Mounng Accessories
PTB - Pole Top Tenon Horizontal Arm Bracket PTB2 - Pole Top Tenon Horizontal Arm Bracket (2@180o)
RPB - Round Pole Horizontal Arm Bracket SPB - Square Pole Horizontal Arm Bracket
WB - Wall Horizontal Arm Bracket
Specicaon drawings for mounng
accessories are available at
Mounng Hardware provided with bracket
3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
Installaon hardware provided by installer
Mounng Hardware provided with bracket
3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
Installaon hardware provided by installer
Installaon hardware provided by installer
Slip ts 2⅜” tenon
RPB Bracket ts pole with
3” to 6” outside diameter
6” Long Mounng Arm 6” Long Mounng Arm
6” Long Mounng Arm
Slip ts 2⅜” tenon
hps://leotek.com/lighng-library/
GreenCobra™ ComfortView™and E-Cobra™LED Street Light
Installaon Guide
Informaon provided subject to change without noce.
Leotek Electronics USA LLC | 1955 Lundy Avenue | San Jose, CA 95131
408.380.1788 | www.leotek.com
Questo manuale è adatto per i seguenti modelli
2
