Lex System SHARK series Manuale utente
SHARK Waterproof
Assembly Guide
Panel PC
Box PC
6G0000-0000-0000
WARNING !
SHARK Waterproof Assembly guide ......................................
SHARK Waterproof BOX PC Exploded Drawing ...................
SHARK Waterproof Panel PC Exploded Drawing ..................
IP (International Protection)
1
4
7
code- Levels of Protection ....................................................... 10
Introduction of necessary tools ..............................................
IP66 Packing list .......................................................................
IP67 Packing list .......................................................................
Difference of Waterproof cables ..............................................
I/O Connector Pinouts ..............................................................
13
14
15
16
17
Contents
WARNING !
1. Please do not remove the caps of waterproof cables unless needed.
2. Waterproof cables must be fastened tightly on the connectors of system.
3. Waterproof cables must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
4. Please align the screw to the system when fasten it.
Crooked angle should be avoided.
5. Align the screws and fasten them diagonally, just loosely.
Tighten them until make sure all screws are enable to be
fastened correctly to the end.
6. All top cover screws must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
7. If the system error occurred, please turn the power off and unplug it from the
power supply before removing system from the water.
8. Please do not unfasten any screw unless the system is clean and
completely dry.
9. Please be aware that even one drop of water might carry a risk of
damage to the waterproof connectors, make sure to avoid when
removing waterproof cables.
10. To avoid causing any damage to the waterproof connectors,
using the standard tools are requested.
1
1. Unscrew ten (M2.5*4) screws from the
bottom cover and then lift the cover out
of the system. (Fig.1)
3. Install the mSATA into the connector
slot at a 45 degree angle. (Fig.3)
2. Unscrew the(M2*6) screw from the screw
thread on motherboard. (Fig.2)
4. Push the mSATA down to the motherboard
Fasten mSATA with the (M2*6) screw.
(Fig.4)
(Fig.1)
(Fig.3)
(Fig.2)
45°
(Fig.4)
SHARK Waterproof Assembly guide
2
8. Connect the SATA DATA cable
with motherboard. (Fig.8)
10. Screw the HDD KIT back to the system
with four (M3*4) screws. (Fig.10)
5. Fasten the HDD on HDD KIT with
four (M3*4) screws. (Fig.5)
9. Connect the SATA Power cable
with motherboard. (Fig.9)
6. Connect the SATA DATA cable
with HDD(Fig.6)
(Fig.5)
(Fig.7)
(Fig.9)
(Fig.6)
(Fig.8)
(Fig.10)
7. Connect the SATA Power cable with HDD.
(Fig.7)
3
12. Screw the bottom cover back to the
system with then (M2.5*4) screws.
(Fig.12)
14. Plug in the waterproof cables. (Fig.14)
11. Attach the thermal pad on the HDD
and avoid the heat-dissipating holes at
the same time. (Fig.11)
13. Remove the waterproof caps. (Fig.13)
(Fig.11)
(Fig.13)
(Fig.12)
(Fig.14)
4
SHARK Waterproof BOX PC Exploded Drawing
7" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1Front Bezel 16HDD 1
2Back Cover 17Key Pad 1
3Front Cover 18Waterproof Cable 7
4O-ring 292I Mainboard 1
5HDD brackrt 1
2
7
1
6
5
3
9
4
8
5
1
9
2
3
2
4
7
5
8
6
11
10
SHARK Waterproof BOX PC Exploded Drawing
10.1" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1SHARK 10.1"(WP),BOX,TOP
COVER,LF,AL 6063,Black,For 3I/2I 17M12 CABLE WP x
2SHARK 10.1,O-RING FOR FRONT
BEZEL,L=795MM,Black 282.5" HDD 1
3SHARK 10.1"(WP),BOX,FRONT
BEZEL,LF,AL 6063,Black 192I Mainboard 1
4SHARK 10.1"(WP),BOX,BOTTOM
COVER,LF,AL 6063,Black 110BATTERY 2S1P 3360mah 1
5SHARK 10.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black x11
SHARK 10.1" BOX PC,Battery
Bracket,FOR 2S1P 3360mah 1
6STAR 10.4",HDD
RACKET,LF,SECC=1.0,MATERIAL 1
6
1
9
2
6
8
5
3
7
2
4
SHARK Waterproof BOX PC Exploded Drawing
10.1" SHARK BOX PC
No. Name Q'ty No. Name Q'ty
1SHARK 10.1"(WP),BOX,TOP
COVER,LF,AL 6063,Black,For 3I/2I 16
STAR 10.4",HDD
RACKET,LF,SECC=1.0,MATERIAL 1
2SHARK 10.1,O-RING FOR FRONT
BEZEL,L=795MM,Black 27M12 CABLE WP x
3SHARK 10.1"(WP),BOX,FRONT
BEZEL,LF,AL 6063,Black 182.5" HDD 1
4SHARK 10.1"(WP),BOX,BOTTOM
COVER,LF,AL 6063,Black 193I Mainboard 1
5SHARK 10.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black 1
7
1
2
3
4
6
7
8
5
9
12
13
10
11
14
15
SHARK Waterproof Panel PC Exploded Drawing
10.1" SHARK Panel PC
No. Name Q'ty No. Name Q'ty
110.1" TOUCH 192I Mainboard 1
2SHARK 10.1,Washer for
Touch,LF,t=1.2mm 110BATTERY 2S3P 1
3SHARK 10.1",FRONT BEZEL-
WP,LF,AL 6063,Black 111BATTERY BRACKET 1
410.1" BOX PC,Power/Reset
Function Key Pad,LF,PET,Black 112HDD BRACKET 1
5M12 CABLE WP x132.5" HDD 1
6LCD 114
SHARK 10.1",Bottom Cover-
WP,LF,AL 6063,Black 1
7SHARK 10.1,O-RING FOR FRONT
BEZEL, L=795MM,Black 115WP-VALVE 1
8SHARK 10.1",CHASSIS-
WP,2I268H/2I385H 1
Altri manuali per SHARK series
1
Indice
Altri manuali Lex System Pannello touch
