Lexing LX-PR-65S Manuale utente

LX-PR-65S Infrared Sensor Instruction

Specifications

Summary

External passive infrared detector fully adjustable vertically and horizontally, activated by small

movements of heat.

Timer adjustable from 20sec to 12min.(reactived by the last detected movement.)

Detection range 12m with 110 degree field of view.

Override switching facility to enable permanent ON operation of light.

Light sensor adjustable to inhibit operation during daylight if required.

5. Rated load: 1000W Max.(220-240V/AC)

500W Max.(100-130V/AC)

6. Detection range: 12m with 110 degree field of view

7. Working temperature: -10~+40°C

8. Working humidity: <95℅RH

1. Power source: 220-240V/AC

100-130V/AC

2. Power frequency: 50/60Hz

3.Time setting: 20sec to 12min±2min

4. LUX night and day adjustments

Correct moving orientation

12m



123mm

76mm

100mm

Detection angle

110°

Sensor information

Planning your installation

First decide on the location bearing in mind that the detector will perform best if mounted between 2 and 2.5

meters from the ground. It is also important to remember not to position the detector where it will reach areas

such as footpaths and roads as this may result in unwanted activations from passers by.

The detector responds better when a person moves across the field of vision as opposed to straight towards

it. Mounting the detector towards the side of a building with the head angles at 45 degree will make the

detector respond better than mounting in the center looking straight ahead.

The detector cannot see through solid objects including glass so care should be taken that field of view is not

obstructed by trees bushes parked cars etc.

The detector must be mounted well clear of central heating outlets or any large reflective surfaces as this may

result in unwanted activations.

Note

Connection-wire diagram

L——brown

N——blue

L——red

Connect Land Nwith power

Connect Nand L with load.

Knob adjustment

1. TIME adjuster:

2. LUX adjuster: adjust level of light operation

20SEC 12MINS

Adjust the light delay

TIME

Night Operation Day Operation

Sensor

Brown

Blue N

Load

LRed

Input

Output

－＋

LUXTIME

Operating instructions

Test mode

In test mode the unit will activate day or night regardless of ambient light levels. Activations during the test

mode will activate the light for 5sec. The unit will progress to AUTO mode automatically after 5 mins.

Auto mode

In auto mode the unit will activate according to the settings selected on the LUX&TIME adjusters.To allow

the unit to work only at night turn LUX to “-“ or to allow unit to operate both day&night to “+”. The amount of

time the unit stays on after activation can be adjusted from between 20sec and 12min using the TIME

adjuster.

Override mode

In override mode the light will remain permanently ON until:

a) The unit is switched OFF and ON quickly.

b) The unit has been on for more than 6 hours.

c) Dawn (light level over or about 300lux) arrives when LUX control set to “-“ position.

Nothing happen

1. Check supply to unit．

Detector clicks but does not operate

1. Check lamps are not broken.

2. Check lamps tight in lampholders.

Light go on and off quickly

1. Ensure light is not being reflected back into sensor.check for white or reflective surfaces in protection

pattern.

2. Note the detector is more sensitive in cold weather.

Light stay on

1. Check unit has not gone into Manual override mode;

2. Adjust time to minimum.

3. Ensure nothing in field of view activating detector.

4. Ensure unit is firmly fixed to a solid object with no moving branches etc. in field of view.

5. Ensure detector is not being activated by stray moving heat sources such as heating outlets cars etc.

Light switch on during storms

Adverse weather conditions and temperature changes can result in unwanted activations. This can be

minished by mounting in a protected location and adjusting sensitivity control. Switch power supply off

during storms.

Fault finding

Maintenance and repair

1.Do not attempt to repair as this could invalidate warranty or result in personal injury.

2.Clean detector lens and outside casing with damp cloth.

Sequence diagram

POWER

OFF

SELF TEST

MODE

Switch on

After 5mins

Switch off then

on once(quickly)

Switch off then

on twice(quickly)

● after 6 hours

● or power OFF-ON once(quickly)

● or at dawn (only when LUX is on

“-” position)

AUTO

MODE

OVERRIDE

MODE

Indice

Altri manuali Lexing Accessori

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente