Lexmark 6500E Manuale utente

Lexmark

Card for IPDS

and

Card for IPDS and SCS/TNe

IPDS Printer and Host Setup Guide

IPDS Printer and Host Setup Guide Notices

NOTICES

Edition Notice

Sixth Edition. April 2011, Rev 006.

Disclaimers

The following paragraph does not apply to any country where such provisions are inconsistent with local law:

LEXMARK INTERNATIONAL, INC. AND KODAK PROVIDE THIS PUBLICATION "AS IS" WITHOUT WAR-

RANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not

allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not

apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to

the information herein; these changes will be incorporated in later editions. Improvements or changes in the

products or the programs described may be made at any time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to

make these available in all countries in which it operates. Any reference to a product, program, or service is not

intended to state or imply that only that product, program, or service may be used. Any functionally equivalent

product, program, or service that does not infringe any existing intellectual property right may be used instead.

Evaluation and verification of operation in conjunction with other products, programs, or services, except those

expressly designated by the manufacturer, are the user's responsibility.

Trademarks

AFP, AS/400, IBM, iSeries, MVS, OS/2, OS/390, OS/400, Print Services Facility, PSF, System/390, zSeries,

and z/OS are trademarks of International Business Machines Corporation in the United States, other countries,

or both.

Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the

United States, other countries, or both.

Lexmark and Lexmark with diamond design and MarkNet are trademarks of Lexmark International, Inc. regis-

tered in the United States and/or other countries.

IPDS Printer and Host Setup Guide - Table of Contents

TABLE OF CONTENTS

Notices ........................................................................................................................................................ 2

Table of Contents.............................................................................................................................................. 3

Equipment Requirements and Specifications................................................................................................ 4

Customer Support............................................................................................................................................. 5

1. iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print

Server ................................................................................................................................................................ 6

2. PSF/MVS LAN Printing Using the Standard Network Port or Internal Print Server ........................... 14

3. PSF/2 LAN Printing Using an Internal LAN Print Server ...................................................................... 22

4. Printer and Host Timeout Values ............................................................................................................ 29

5. Printer Messages and Problems ............................................................................................................ 31

IPDS Printer and Host Setup Guide Equipment Requirements And Specifications

EQUIPMENT REQUIREMENTS AND

SPECIFICATIONS

This guide provides information to help you configure the host and printer to print IPDS jobs. The information in

this guide applies to the following printers and Multifunction Products (MFPs).

• Lexmark C734, C736

• Lexmark C792

• Lexmark C925

• Lexmark E460dn, E460dw, E462dtn

• Lexmark T650, T652

•LexmarkT654

• Lexmark T656dne

•LexmarkW850

• Lexmark X463de, X464de

• Lexmark X466dte, X466dtwe

• Lexmark X651de, X652de

• Lexmark X654de, X656de

• Lexmark X658de

• Lexmark X734de, X736de, X738de

• Lexmark X860de, X862de, X864de

• Lexmark X792

• Lexmark X925

• Lexmark C950

• Lexmark X950, X952, X954

• Lexmark X548

• Lexmark 6500e

Unless otherwise specified, in the rest of this guide the term "printer" covers both printers and MFPs. The term

"Card for IPDS" also refers to the "Card for IPDS and SCS/TNe".

To print IPDS jobs, the printer must have the optional Card for IPDS and SCS/TNe* or Card for IPDS installed,

a required** minimum of user memory (DRAM), and one of the following:

• Standard Network (Ethernet connection integrated into printer system board)

• MarkNet internal LAN print server (optional card providing Ethernet connection).

• Lexmark wireless internal print server.

To install the printer, determine the host, host software, and type of printer connection you will be using. Find

the appropriate chapter in the Table of Contents and follow the steps to configure the host and printer.

*Note: SCS/TNe is not supported on all printers.

**Note: A minimum amount of user memory (DRAM) may be required to support IPDS. Refer to your model’s

IPDS Emulation User’s Guide for memory requirements and recommendations.

IPDS Printer and Host Setup Guide Equipment Requirements And Specifications

Customer Support

If you cannot find answers in this guide about using the IPDS emulation, or require firmware updates, please

contact your point of purchase, your local Lexmark office, or check the Lexmark support web site at

http://support.lexmark.com/index?page=localeSelect&locale=en&jumppage=home

IPDS Printer and Host Setup Guide iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server

1. iSeries and AS/400 LAN Printing Using the Printer

Standard Network Port or MarkNet Internal Print

Server

With the optional Card for IPDS and a LAN print server installed, the printer can receive, process, and print

AFP/IPDS print jobs over TCP/IP from the following IBM software:

• PSF/400 V3R1-R3, V3R6-R7, V4R1-R5, V5R1-R4, V6R1, or greater

The information below will lead you through the steps for setting up the AS/400, or iSeries, and the printer to

print IPDS jobs over a LAN. The printer must be configured with a Standard Network port or MarkNet internal

LAN print server.

Refer to the IPDS User’s Guide for detailed instructions on using the control panel to select and change option

settings.

Steps

The following steps must be completed to begin printing IPDS jobs.

Choose a Printer Port for Use in the Device Description

Create a PSFCFG

Create a Printer Device Description

Configure the Printer’s Print Server TCP/IP Settings

Select the IPDS Emulation, Bar Code Size, Host Resolution, and Fax Interrupt Settings

Verify IPDS Printing

Troubleshooting

Step 1 Choose a Printer Port for Use in the Device Description

Several printer ports are available for receiving IPDS jobs when using the printer Standard Network port or the

MarkNet internal LAN print server. The printer port will be used in one of the following steps.

Port descriptions:

•Port 5001 - This is the recommended port selection for receiving IPDS jobs. This port is only used for

receiving IPDS jobs.

•Port 9600 - This port is only provided for compatibility with some older printers.

NOTE: Some previous printers supported port 9100 for IPDS printing. If you are replacing a printer using port

9100, change to port 5001.

Step 2 Create a PSFCFG

Note: Examplesshowing parametersdisplayedonan iSeriesmay bedifferent than theparametersdisplayed

on your system. Examples are shown with V6R1 parameters.

Define a PSF configuration object for your printer using CRTPSFCFG. The PSFCFG object defined in this step

is referenced in the printer device description (CRTDEVPRT). More than one printer can use this object.

Below is an example of a PSF configuration. The parameters in bold are the parameters which must be

changed for printing IPDS jobs.

IPDS Printer and Host Setup Guide iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server

Press PF9 to show the following parameters:

Example PSFCFG with parameters to change shown in bold.

PSF configuration PSFCFG > IPDSPRT1

(Note: IPDSPRT is a user defined name.)

Library............................... > Your LIB

User resource library list.. USRRSCLIBL *JOBLIBL

Device resource library list DEVRSCLIBL *DFT

+ for more values

IPDS pass through..................... IPDSPASTHR > *NO <note1>

Activate release timer................ ACTRLSTMR *NORDYF

Release timer......................... RLSTMR > *SEC15 <note2>

Restart timer......................... RESTRTMR *IMMED

APPC and TCP/IP retry count........... RETRY 15

Delay time between APPC retries....... RETRYDLY 90

Acknowledgement frequency............. ACKFRQ 100

Printer response timer................ PRTRSPTMR *NOMAX

Generate PDF output................... PDFGEN *NONE

Save AFP data AFPSAVE *NO

Text 'description'.................... TEXT > 'PSFCFG for IPDS

Printer'

(Note: ‘PSFCFG for IPDS Printer’ is user defined text.)

Press PF10 to show the following parameters:

Additional Parameters

Automatic session recovery: AUTOSSNRCY

Enabled........................... *NO

Message option....................

Blank page............................ BLANKPAGE *YES

Page size control..................... PAGSIZCTL *NO

Resident fonts........................ RESFONT *YES

Resource retention.................... RSCRET *YES

Edge orient........................... EDGEORIENT *NO

Use outline fonts..................... USEOUTLFNT *NO <note3>

PSF defined option.................... PSFDFNOPT *NONE

Font substitution messages............ FNTSUBMSG *YES

Capture host fonts at printer......... FNTCAPTURE *NO <note4>

Font resolution for formatting........ FNTRSL *SEARCH

Font mapping table.................... FNTTBL *NONE

Library.............................

Cut sheet emulation mode.............. CSEMODE *NONE

Use DBCS simulation fonts............. MAPIGCFNT *NO

Replace............................... REPLACE *YES

Authority............................. AUT *LIBCRTAUT

Cut sheet emulation mode..............

Use DBCS simulation font..............

Generate PDF output...................

*NONE

*NO

*NONE

PDF device emulation type.............

PDF paper size drawer 1............... > *IP40240

*LETTER

IPDS Printer and Host Setup Guide iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server

Note 1: IPDS pass through may be set to *YES. This may increase job performance. Selecting *YES may

change the fonts downloaded from the host and change paper jam recovery action between the host

and printer.

Note 2: SEC15 is recommended. Refer to

“Printer and Host Timeout Values” [page 29]

for information on

selecting other Release Timer values.

Note 3: Use outline fonts controls the type of fonts downloaded to the printer. When set to *YES,

outline fonts are downloaded to the printer. When set to *NO, raster fonts are downloaded to the

printer. When the outline or raster fonts are marked eligible for capture on the host, the host will send

fonts which can be captured at the printer.

Note 4: Capture host fonts at printermustbesetto*YES and fonts must be marked eligible

to be captured before the host will send fonts which can be captured to the printer. Refer to the IPDS

Emulation User's Guide for additional information on capturing fonts.

Step 3 Create a Printer Device Description

Note: Examples showing parameters displayed on an AS/400 or iSeries may be different than the

parameters displayed on your system. Examples are shown with V6R1 parameters.

Create a printer device description for your printer using CRTDEVPRT.

Below is an example of a device description. The parameters in bold are the parameters which must be

changed for printing IPDS jobs.

PDF paper size drawer 2................ *LETTER

PDF multiple group handling:.........

Acknowledge multiple groups.......... *NO

Process option.....................

PDF fonts inline ..................... *YES

PDF data queue........................ *NONE

Library ............................

PDF mail server ..................... *SNDDST

Sender of PDF mail ................... *SPLFOWN

PDF administrator ................... *NONE

PDF user program ..................... *NONE

Library..............................

PDF mapping object.................... *NONE

Library..............................

PDF output queue......................

Library...................

PDF file location.....................

Save AFP data ....................... *NO

AFP output queue......................

Library..............................

Text description .....................

Device resource library list: ........ *DFT

Example CRTDEVPRT with parameters to change shown in bold.

Device description.................... DEVD > IPDSPRT1

(Note: IPDSPRT is a user defined name.)

Device class.......................... DEVCLS > *LAN

Device type........................... TYPE > *IPDS

IPDS Printer and Host Setup Guide iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server

Device model.......................... MODEL > 0

LAN attachment........................ LANATTACH > *IP

Advanced Function Printing............ AFP > *YES

Port number........................... PORT > 5001

(Note: Port number selected in step

above.)

Online at IPL......................... ONLINE *YES

Font: FONT

Identifier.......................... > 11

Point size.......................... *NONE

Form feed............................. FORMFEED > *AUTOCUT

Separator drawer...................... SEPDRAWER *FILE

Separator program.....................

Library............................. SEPPGM *NONE

Printer error message................. PRTERRMSG *INQ

Message queue......................... MSGQ Your Queue

Library............................. Your LIB

(Note: Port number selected in step 1 above.)

Activation timer...................... ACTTMR > *NOMAX <note1>

Image configuration IMGCFG *NONE

Maximum pending requests ............. MAXPNDRQS 6

Print while converting................ PRTCVT *YES

Form definition....................... FORMDF F1C10110

Library............................. *LIBL

Remote location: RMTLOCNAME

Name or address..................... > ’157.184.115.32’

(See your Network Administrator for address.)

User-defined options ................. USRDFNOPT *NONE

+for more values

User-defined object: USRDFNOBJ

Object.............................. > Your OBJ

Library........................... > Your LIB

Object type......................... > *PSFCFG

Data transform program................ USRDTATFM *NONE

Library.............................

User defined driver program........... USRDRVPGM *NONE

Library.............................

Secure connection..................... SECURECNN *NO

Validation list....................... VLDL *NONE

Library............................

Publishing information: .............. PUBLISHINF

Support duplex..................... *UNKNOWN

Support color...................... *UNKNOWN

Pages per minute black............. *UNKNOWN

Pages per minute color............. *UNKNOWN

Location........................... *BLANK

Data streams supported ............ *UNKNOWN

+ for more values

Text 'Description'.................... TEXT > 'IPDS Printer'

(Note: 'IPDS Printer' is user defined text.)

Additional Parameters

Example CRTDEVPRT with parameters to change shown in bold.

IPDS Printer and Host Setup Guide iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server

Note 1: Setting the Activation Timer to *NOMAX allows multiple writers or multiple hosts to use

the same printer. The writer does not time out while waiting on the printer to start a new job.

Step 4 Configure the Printer’s Print Server TCP/IP Settings

To enable IPDS printing with a Standard Network port or a MarkNet internal LAN print server, several settings

must be verified. You can verify these settings from the printer control panel as shown below.

1From a Ready state press the MENU button (printers). Touch or on touch screens.

2Use the navigation buttons or icon to scroll to Network/Ports.

3Select Network/Ports.

TIp: To do this on printers, press the Select button ; on touch screens touch Network/Ports.

4Now you will see a list of menus. Select the Standard Network menu.

5Select Std Network Setup.

6Select TCP/IP.

7Use the navigation buttons or icons to scroll through the options. Check each of the following settings and

change them as needed to configure TCP/IP communication.

Remote network identifier............. RMTNETID *NETATR

Workstation customizing object........ WSCST *NONE

Library............................

Authority............................. AUT *LIBCRTAUT

TCP/IP Settings

Parameter Value

Activate On

(Printers: Must be "On" to enable TCP/IP communi-

cations. MFPs: not displayed.)

IP Address 157.184.67.102

(Address available from your network administrator)

Netmask 255.255.255.0

(Appropriate netmask for your network)

Gateway 157.184.67.1

(IP address of your IP gateway)

Enable DHCP On or Off

(On, if you use a DHCP server.)

(Off, if you set the IP address another way.)

Example CRTDEVPRT with parameters to change shown in bold.

Altri manuali per 6500E

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lexmark Hardware per computer

Lexmark

Lexmark 6500E Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente