LG MULTI V ARNU18GTLA4 Manuale utente

www.lg.com

P/NO : MFL69440006

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring standards

by authorized personnel only.

Please retain this installation manual for future reference after reading it thoroughly.

CEILING CASSETTE - 2WAY

Original instruction

INSTALLATION MANUAL

AIR

CONDITIONER

ENGLISH

2Indoor Unit

Ceiling Cassette - 2Way Type Indoor Unit Installation Manual

TABLE OF CONTENTS

o Installation guide map

oFour type "A" screws & plas-

tic anchors

oConnecting cable

oPipes: Gas side

Liquid side

(Refer to Product

Data)

oInsulation materials

oAdditional drain pipe

oLevel gauge

oScrew driver

oElectric drill

oHole core drill

oHorizontal meter

oFlaring tool set

oSpecified torque wrenches

(different depending on model No.)

oSpanner.......Half union

oHexagonal wrench

oGas-leak detector

oVacuum pump

oGauge manifold

oOwner's manual

oThermometer

Installation Parts ...................3

Safety Precautions.................4

Installation

Selection of the best

location...................................6

Ceiling dimension and hang-

ing bolt location......................7

Wiring Connection.................8

Installation of Decoration

Panel......................................9

Drain Piping .........................10

DIP Switch Setting ..............12

Group Control Setting .........13

Model Designation ..............18

Airborne Noise Emission ....18

Limiting concentration .........18

Installation Requirements Required Parts Required Tools

Installation Manual 3

Installation Parts

Anti-bacteria filter

Air Outlet

Air Intake

Wired Remote Controller(Accessory)

Installation Parts

Name Drain hose Clamp metal

Washer for

hanging bracket

Clamp

(Tie Wrap)

Insulation for

fitting

Quantity

1 EA 2 EA 8 set 4 EA 1 EA

Shape

• Screws for fixing panels are attached to decoration panel.

for gas pipe

for liquid pipe

(Other)

• Paper pattern for

installation

• Owner's manual

• Installation man-

ual

ENGLISH

Installation Tool

Do not modify or extend the

power cable.

• There is risk of fire or electric

shock.

Do not let the air conditioner

run for a long time when the

humidity is very high and a

door or a window is left open.

• Moisture may condense and

wet or damage furniture.

Be cautious when unpacking

and installing the product.

• Sharp edges could cause in-

jury. Be especially careful of the

case edges and the fins on the

condenser and evaporator.

Safety Precautions

4Indoor Unit

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be

followed.

nBe sure to read before installing the air conditioner.

nBe sure to observe the cautions specified here as they include important items related to safety.

nIncorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classi-

fied by the following indications.

nMeanings of symbols used in this manual are as shown below.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

WARNING

nInstallation

Do not use a defective or un-

derrated circuit breaker. Use

this appliance on a dedicated

circuit.

• There is risk of fire or electric

shock.

For electrical work, contact

the dealer, seller, a qualified

electrician, or an Authorized

Service Center.

• Do not disassemble or repair

the product. There is risk of fire

or electric shock.

Always ground the product.

• There is risk of fire or electric

shock.

Install the panel and the

cover of control box securely.

• There is risk of fire or electric

shock.

Always install a dedicated

circuit and breaker.

• Improper wiring or installation

may cause fire or electric

shock.

Use the correctly rated

breaker or fuse.

• There is risk of fire or electric

shock.

Installation Manual 5

Safety Precautions

nOperation

For installation, always con-

tact the dealer or an Author-

ized Service Center.

• There is risk of fire, electric

shock, explosion, or injury.

Do not install the product on

a defective installation stand.

• It may cause injury, accident, or

damage to the product.

Be sure the installation area

does not deteriorate with age.

• If the base collapses, the air

conditioner could fall with it,

causing property damage,

product failure, and personal in-

jury.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Use two or more people to lift and transport the product.

• Avoid personal injury.

Use a vacuum pump or inert (nitrogen) gas

when doing leakage test or air purge. Do not

compress air or oxygen, and do not use flam-

mable gases. Otherwise, it may cause fire or

explosion.

• There is the risk of death, injury, fire or explosion.

Do not turn on the breaker or power under

condition that front panel, cabinet, top cover,

control box cover are removed or opened.

• Otherwise, it may cause fire, electric shock, ex-

plosion or death.

ENGLISH

Always check for gas (refrig-

erant) leakage after installa-

tion or repair of product.

• Low refrigerant levels may

cause failure of product.

Install the drain hose to en-

sure that water is drained

away properly.

• A bad connection may cause

water leakage.

Keep level even when in-

stalling the product.

• To avoid vibration or water

leakage.

CAUTION

nInstallation

• There should not be any heat source or steam near the unit.

• There should not be any obstacles to the air circulation.

• A place where air circulation in the room will be good.

• A place where drainage can be easily obtained.

• A place where noise prevention is taken into consideration.

• Do not install the unit near the door way.

• Ensure the spaces indicated by arrows from the wall, ceiling, or other obstacles.

• The indoor unit must have the maintenance space.

Read completely, then follow step by step.

Unit:mm

Ceiling

Ceiling Board

200 or more

Above 1 800

3 000 or less

1 000

or more

500 or

300 or less

Floor

20±3

Installation

Selection of the best location

CAUTION : In case that the unit is installed near the sea, the installation parts

may be corroded by salt. The installation parts (and the unit) should be taken ap-

propriate anti-corrosion measures.

Installation

6Indoor Unit

Installation Manual 7

Installation

ENGLISH

Ceiling dimension and hanging bolt location

Level gauge

Ceiling

Ceiling board

1 010 (Ceiling opening)

877 (Hanging bolt)

482(Hanging bolt)

830 60

550

600 (Ceiling opening)

unit: mm

• The dimensions of the paper model for installation are the same as those of the ceiling

opening dimensions.

• Avoid the following installation location.

1. Such places as restaurants and kitchen where considerable amount of oil steam and flour is

generated.

These may cause heat exchange efficiency reduction, or water drops, drain pump mal-function.

In these cases, take the following actions;

• Make sure that ventilation fan is enough to cover all noxious gases from this place.

• Ensure enough distance from the cooking room to install the air conditioner in such a place

where it may not suck oily steam.

2. Avoid installng air conditioner in such

places where cooking oil or iron

powder is generated.

3. Avoid places where inflammable gas

is generated.

4. Avoid places where noxious gas is

generated.

5. Avoid places near high frequency

generators.

NOTICE

CAUTION :

• This air-conditioner uses a drain

pump.

• Install the unit horizontally using a

level gauge.

• During the installation, care should

be taken not to damage electric

wires.

• Select and mark the position for fixing bolts

and piping hole.

• Decide the position for fixing bolts slightly

tilted to the drain direction after considering

the direction of drain hose.

• Drill the hole for anchor bolt on the wall.

Use the ventilation fan

for smoke-collecting

hood with sufficient

capacity.

Cooking table

Air conditioner

Take enough

distance

Set screw of

paper pattern (4 pieces)

Paper pattern

for installation

90 mm

Adjust the

same height

Ceiling board

Ceiling

Flat washer for M10

(accessory)

Keep the length of the bolt

from the bracket to 40 mm

Open the ceiling board

along the outer edge of the

paper pattern

Flat washer for M10

(accessory)

Hanging bolt

(W3/8 or M10)

Nut

(W3/8 or M10)

Nut

(W3/8 or M10) Air Conditioner body

Ceiling board

• The following parts are local purchasing.

①Hanging Bolt - W 3/8 or M10

②Nut - W 3/8 or M10

③Spring Washer - M10

④Plate Washer - M10

Terminal Block Indoor

Terminal Block of outdoor unit

1(L) 2(N) 3 4

INDOOR POWER INPUT

SODU IDU INTERNET DRY1 DRY2 GND 12V

A B A - - - -

Outdoor unit

Connect the wires to the terminals on the control board individually according to the outdoor unit

connection.

• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of

indoor unit respectively.

Wiring Connection

WARNING : Make sure that the screws of the terminal are free from looseness.

CAUTION : The Power cord connected to the unit should be selected according

to the following specifications.

CAUTION : Tighten the nut and bolt

to prevent the unit from falling.

Installation

8Indoor Unit

Installation Manual 9

Installation

ENGLISH

Piping side

Air conditioner unit

Decorative panel

Push

Decorative panel

fixing screws

(hexagon M6 screws)

Temporary fitting

at 2 poles

(Tightening about 10 mm)

Control box cover

Cover

Plasma filter

Key holes

Decorative panel

fixing screws

(Hexagon M6 screw)

Louver motor

Ratch

pull

Inlet Grille

Cool air leakage

(no good)

Decoration panel

Air conditioner

unit

Ceiling

board

Fit the insulator (this part) and

be careful for cool air leakage

Decoration panel

Air conditioner

unit

Ceiling

board

Good example Bad example

Installation of Decoration Panel

CAUTION : Install

certainly the dec-

oration panel.

Cool air leakage

causes sweating.

Water drops

fall.

1. Temporarily fix two decoration panel fixing screws (hexagon M5 screw) on the unit body.

(Tighten by amount 10 mm in length.) The fixing screws (hexagon M5 screw) are in-

cluded the indoor unit box.

Remove the air inlet grille from the decoration panel. (Remove the hook for the air inlet grille cord.)

3. Hook the decoration panel key hole ( ) on the screws fixed in step above, and slide

the panel so that the screws reach the key hole edge.

Retighten completely two temporarily fixed screws and other two screws. (Total 4 screws)

5. Connect the louver motor connector and display connector.

6. After tightening these screws, install the air inlet grille (including the air filter).

The decoration panel has its installa-

tion direction.

Before installing the decoration panel, al-

ways remove the paper template.

• Drain piping must have down-slope (1/50 to

1/100): be sure not to provide up-and-down slope

to prevent reversal flow.

• During drain piping connection, be careful not to

exert extra force on the drain port on the indoor

unit.

• The outside diameter of the drain connection on

the indoor unit is 32 mm.

• Be sure to install heat insulation on the drain pip-

ing.

Piping material: Polyvinyl chloride pipe VP-25

and pipe fittings

The air conditioner uses a drain pump to drain water.

Use the following procedure to test the drain pump operation:

• Connect the main drain pipe to the exte-

rior and leave it provisionally until the

test comes to an end.

• Feed water to the flexible drain hose

and check the piping for leakage.

• Be sure to check the drain pump for nor-

mal operating and noise when electrical

wiring is complete.

• When the test is complete, connect the

flexible drain hose to the drain port on

the indoor unit.

Heat insulation material: Polyethylene foam

with thickness more than 8 mm.

Drain test

Flexible drain hose

Maintenance

drain port

Upward

routing

not allowed

Pipe clamp

Indoor unit

1/50~1/100

MAX 700 mm

Feed water

Drain Pump

Drain pan

Flexible drain hose

(accessory)

Main

drain pipe

Glue the joint

Drain

port

Drain hose connection

Use the clip (accessory)

Flexible drain hose

1/50~1/100 slope

Hanger

distance Hanger Bracket

Max 700 mm

Flexible drain hose

Insulation

Metal

clamp

Max 300 mm 1~15 m

Drain Piping

CAUTION : The supplied flexible

drain hose should not be curved,

neither screwed. The curved or

screwed hose may cause a leakage

of water.

Installation

10 Indoor Unit

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Frigidaire

Frigidaire FFRE0533S1E0 Manuale utente

Samsung

Samsung AS09HM3N Manuale utente

Frigidaire

Frigidaire CRA073PU11 Manuale del proprietario

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente