LG LVC-S10 Manuale utente
Operating Instructions
LVC-S10/LVC-S101
LVC-S20/LVC-S201
Before installing and using the camera,
please read these instructions throughly
and retain them for later reference.
2
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation! This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning
Regulatory Notices
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet Refer servicing
to qualified personnel only.
Contents
Features ..................................................................................................................................3
Cautions for Safe Operation
......................................................................................................4
Operating Controls and Their Functions ..............................................................................5-6
Connections .........................................................................................................................7-8
Back Focus Adjustment ..........................................................................................................9
Installation of Camera............................................................................................................10
Function Set up ................................................................................................................11-18
Specifications ...................................................................................................................19-22
FEATURES
This color video camera is designed for use
in monitoring system.
•High resolution and high sensitivity with a
1/3 inch Super HAD CCD (Charge Coupled
Device)
•Built-in Digital Zoom x2
•Easy operation for lens application
(C/CS Adjustment type mount)
•Built-in Motion Detection
•
External Sync.(Line Lock, Genlock, VD Lock)
•On Screen display
•Isolated power circuit
Maintence of the unit
•Remove dust or dirt on the surface of the
lens with a blower.
•Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampended with a
small quantity of neutral detergent and
then wipe dry.
•Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and insecticides
.
They may damage the surface of the body.
3
4
Power Supply
S10, S20 : They must be operated with a AC
24V class 2 power supply and DC12V
alternatively.
In the U.S.A, use a Power supply which is UL
Listed.
In the Canada, use a Power supply which is
CSA Certified.
* Notes:Be careful of AC frequency when the
camera is operated with Line lock mode.
AC24V(50Hz): S10HP/S10NP/S20HP
AC24V(60Hz): S10HM/S10NM/S20HM
S101, S201:They must be operated with the
range from AC100V to AC240V
* Notes:Be careful of AC frequency when the
camera is operated with Line lock mode.
AC100V-240V(50Hz):S101HP/S101NP/
S201HP
AC100V-240V(60Hz):S101HM/S101NM/
S201HM
Handling of the unit
Be careful not to spill water or other liquids on
the unit. Be cautions not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get a cause of fire or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as light
fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
•Extremely hot or cold places (operating
temperature -10
o
C~50
o
C, however, we
recommend that the unit be used within a
temperature range of 0
o
C~45
o
C)
•Damp or dust place
•Places exposed to rain
•Places subject to strong vibration
•Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Cautions for Safe Operation
5
Control names and Location
1. Tripod adaptor
This adaptor can also be attached on the bottom of the camera
2. Flange-back Adjusting Lever
This lever is used to adjust the back focal length or picture focus. Rotate this
lever clockwise for a C-mount lens or counterclockwise for a CS-mount lens.
3.
Function key cover
4.
Function key button (see page 13)
5.
Auto Iris Lens Connector
This connector, which is built-in 4 pin male connector, is used to connect with
the auto iris lens.
6.
CCD Cover
7.
Power indicator
This indicator light up when the power of this camera is on.
8.
Connection Terminal
These 4 Terminals are used to connect the auto iris lens which should be
connected by wire.
The first terminal from the left is used to connect Alarm Output.
9.
Power Cord Socket
This socket is used to connect the power cord.
10.Auto Iris Lens Selection Switch
This switch is used to set the mode with user’s preference.(user selection)
11.V-PHASE adjustment screw
12.AC/DC Compatible Input Terminal(DC12V/AC24V)
13.External Sync.Input jack
(GEN-LOCK/VD LOCK)
14.Video Output Jack
OPERATING CONTROLS AND THEIR FUNCTIONS
POWER
Alarm Out
Da-
VCC Video GND
Da+ Dr+ Dr-
AC 100-240V~
Class 1 Only
GEN-LOCK VIDEO OUT
V.PHASE
VIDEO
ELC
DC
POWER
Alarm Out
Da-
VCC Video GND
Da+ Dr+ Dr-
Class 2 Only
1
2
GEN-LOCK VIDEO OUT
V.PHASE
VIDEO
ELC
GND
DC
DC 12V
IN
AC 24V
IN
1 2
3 4 5 6
7 8
9 10 11 12 13 14
S101,S201’ S S10,S20’ S
The Adjustment method of Line Lock Phase
When using a camera switcher to connect 2 cameras or
more to one monitor, there may be a vertical roll of the
images when switched. In such a case, refer to the
below.
-The vertical sync phase can be manually adjusted
within the range approximately from -90oto 90o.
- Switch the display on the monitor from camera1 to
camera2.
Adjust the V.PHASE volume on camera2 until the
vertical roll of the image stops.
If more than two cameras are used, please repeat this
procedure for all the cameras.
- If you can’t adjust vertical sync. phase,
Please exchange the polarity of input terminal.
➀ Camera switcher
② Monitor
➂ Vertical phase
6
OPERATING CONTROLS AND THEIR FUNCTIONS
1 2
3
7
CONNECTIONS
Power Connection
LVC-S101, LVC-S201 (AC100V-AC240V)
1. Connect the AC power cord (supplied as an accessory) to the power cord
socket of the camera.
2. Connect the AC power cord to an electrical outlet of 100V - 240V
LVC-S10, LVC-S20 (DC12V/AC24V Compatible)
1. DC 12V Power Supply
Remove the insulation on the power cable as illustrated and connect the
power cord to the AC/DC compatible terminals on rear panel of the camera.
Note :
Be cautious of the polarity of positive and negative.
Be sure to confirm DC 12V ±2V
2. AC 24V Power Supply
Connect the power cable to the AC/DC compatible input terminal on the rear
panel of the camera
Note :
To get the optimum performance from the unit, be sure to connect to an AC
supply of 24V ±10%
Connecting the monitor
➀To VIDEO OUT
②To video input on the monitor
POWER
AC 100-240V~
Cl 1 O l
G
12 V DC
(10.5V~24V)
DC 12V
IN
24 VAC
(19.5V~28V)
AC 240V
IN
1
2
GND
1 2
Mounting Auto Iris Lens
1. Mount the lens by turning it clockwise on the lens mount of the camera.
2. Set the slide switch of rear panel to your lens type
3. Connect the lens cable to the auto iris lens connector on the side of the
camera.
4. If the lens connection is not connector type but wired cable type, connect
this cable to iris terminal block at rear panel.
In this case, note the terminal assignment of DC or Video lens.
Notes: Rotate the lever clockwise until it stops.
If the lever is not at the end, the inner glass or CCD image sensor may be
damaged.
Auto Iris 4 Pin Plug Connector
Alarm Connection
1. Connect the alarm out from terminal to VCR or other equipment.
2. Set the alarm mode by using Menu function (see page 13)
Notes: Alarm GND is shared with Auto Iris GND
8
Lens No Connection
DC
1
2
3
4
Damp -
Damp +
Drive +
Drive -
Lens No Connection
Video
1
2
3
4
DC 12V
NOT USED
Video
Gnd
Auto
IRIS
Lens
Flange-Back Focus adjusting lever
1
2
Alarm Out
Da-
VCC Video GND
Da+ Dr+ Dr-
1
2
43
Alarm
/ VCR
Alarm Out
Da-
VCC Video GND
Da+ Dr+ Dr-
9
1. Loosen the screws on the flange -back adjusting lever.
2. Turn the flange-back adjusting lever to the proper focus position.
3. Tighten the screws with (-)driver on the flange-back adjusting lever
BACK FOCUS ADJUSTMENT
Lever
1
2
3
Flange-Back
adjusting lever
10
This camera is mounted with tripod which makes it possible to install from both of
the bottom and the top of the unit as illustrated.
INSTALLATION OF CAMERA
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali LG Telecamera di sicurezza
